Max NF550/15-65 Betriebsanleitung

NF550/15-65

15 GA. ANGLED FINISH NAILER

BEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WARNING

AND INSTRUCTIONS.

KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.

WARNING:

OPERATING and MAINTENANCE MANUAL

DEFINITIONS OF SIGNAL WORDS

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

NOTE: Emphasizes essential information.

INDEX

ENGLISH Page 3 to 16 Page

ENGLISH

NF550/15-65

15 GA. ANGLED FINISH NAILER

INDEX

1. SAFETY INSTRUCTIONS

……………

2. SPECIFICATIONS &

TECHNICAL DATA

……………………

3. AIR SUPPLY AND CONNECTIONS

…

4. INSTRUCTIONS FOR OPERATION

…

5. MAINTAIN FOR PERFORMANCE

…

6. STORING

……………………………

7. TROUBLESHOOTING/REPAIRS

……

OPERATING and MAINTENANCE MANUAL

BEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WARNING

AND INSTRUCTIONS.

KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE.

WARNING:

1. SAFETY INSTRUCTIONS

PRECAUTIONS ON USING THE TOOL

1. WEAR SAFETY GLASSES OR GOGGLES

Danger to the eyes always exists due to the possibility of dust being blown up by the exhausted air

or of a fastener flying up due to the improper handling of the tool. For these reasons, safety glasses

or goggles shall always be worn when operating the tool.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment

must conform to the requirements of the American National Standards Institute, ANSI Z87.1 (Council

Directive 89/686/EEC of 21 DEC. 1989) and provide both frontal and side protection.

The employer is responsible to enforce the use of eye protection equipment by the tool operator

and all other personnel in the work area.

NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

2. EAR PROTECTION MAY BE REQUIRED IN SOME ENVIRONMENTS

As the working condition may include exposure to high noise levels which can lead to hearing

damage, the employer and user should ensure that any necessary hearing protection is provided and

used by the operator and others in the work area.

3. DO NOT USE ANY POWER SOURCE EXCEPT AN AIR COMPRESSOR

The tool is designed to operate on compressed air. Do not operate the tool on any other highpressure

gas, combustible gases (e.g., oxygen, acetylene, etc.) since there is the danger of an explosion. For

this reason, absolutely do not use anything other than an air compressor to operate the tool.

4. OPERATE WITHIN THE PROPER AIR PRESSURE RANGE

The tool is designed to operate within an air pressure range of 78 to 100 p.s.i. (5.5 to 7 bar).

The pressure should be adjusted to the type of the work being fastened. The tool shall never be

operated when the operating pressure exceeds 120 p.s.i. (8 bar).

Never connect the tool to air pressure which potentially exceeds 200 p.s.i. (14 bar) as the tool can

burst.

5. DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE

Never operate the tool near a flammable substance (e.g., thinner, gasoline, etc.). Volatile fumes from

these substances could be drawn into the compressor and compressed together with the air and this

could result in an explosion.

6. DO NOT USE A WRONG FITTINGS

The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting

is used, the tool can remain charged with air after disconnecting and thus will be able to drive a

fastener even after the air line is disconnected, possibly causing injury.

7. DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE WHEN THE TOOL IS NOT

IN USE

Always disconnect the air supply from the tool and empty the magazine when operation has been

completed or suspended, when unattended, moving to a different work area, adjusting,

disassembling, or repairing the tool, and when clearing a jammed fastener.

WARNING:

TO AVOID SEVERE PERSONAL INJURY OR PROPERTY DAMAGE

BEFORE USING THE TOOL, READ CAREFULLY AND UNDERSTAND THE FOLLOWING

“SAFETY INSTRUCTIONS”. FAILURE TO FOLLOW WARNINGS COULD RESULT IN DEATH OR

SERIOUS INJURY.

100

8. INSPECT SCREW TIGHTNESS

Loose or improperly installed screws or bolts cause accidents and tool damage when the tool is put

into operation. Inspect to confirm that all screws and bolts are tight and properly installed prior to

operating the tool.

9. DO NOT TOUCH THE TRIGGER UNLESS YOU INTEND TO DRIVE A FASTENER

Whenever the air supply is connected to the tool, never touch the trigger unless you intend to drive

a fastener into the work. It is dangerous to walk around carrying the tool with the trigger pulled, and

this and similar actions should be avoided.

10. NEVER POINT THE DISCHARGE OUTLET TOWARD YOURSELF AND OTHER PERSONNEL

If the discharge outlet is pointed toward people, serious accidents may be caused when misfiring.

Be sure the discharge outlet is not pointed toward people when connecting and disconnecting the

hose, loading and unloading the fasteners or similar operations.

11. USE SPECIFIED FASTENERS (SEE PAGE 7)

The use of fasteners other than specified fasteners will cause the tool malfunction. Be sure to use

only specified fasteners when operating the tool.

12. PLACE THE DISCHARGE OUTLET ON THE WORK SURFACE PROPERLY

Failure to place the discharge outlet of the nose in a proper manner can result in a fastener flying

up and is extremely dangerous.

13. KEEP HANDS AND BODY AWAY FROM THE DISCHARGE OUTLET

When loading and using the tool, never place a hand or any part of body in fastener discharge area

of the tool. It is very dangerous to hit the hands or body by mistake.

14. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE AND CORNER OF THE WORK AND THIN

MATE RIAL

The workpiece is likely to split and the fastener could fly free and hit someone.

15. DO NOT DRIVE FASTENERS ON TOP OF OTHER FASTENERS

Driving fasteners of the top of other fasteners may cause deflection fasteners which could cause

injury.

16. REMOVING THE FASTENERS AFTER COMPLETING OPERATION

If fasteners are left in the magazine after the completion of operation, there is the danger of a serious

accident occurring prior to the resumption of operation, should the tool be handled carelessly, or

when connecting the air fitting. For this reason, always remove all fasteners remaining in the

magazine after completion of the operation.

17. CHECK OPERATION OF THE CONTACT TRIP MECHANISM FREQUENTLY IN CASE OF

USING A CONTACT TRIP TYPE TOOL

Do not use the tool if the trip is not working correctly as accidental driving of a fastener may result.

Do not interfere with the proper operation of the contact trip mechanism.

18. WHEN USING THE TOOL OUTSIDE OR ELEVATED PLACE

When fastening roofs or similar slanted surface, start fastening at the lower part and gradually work

your way up. Fastening backward is dangerous as you may loose your foot place.

Secure the hose at a point close to the area you are going to drive fasteners. Accidents may be

caused due to the hose being pulled inadvertently or getting caught.

19. NEVER USE THE TOOL IF ANY PORTION OF THE TOOL CONTROLS (e.g., TRIGGER, CONTACT

ARM) IS INOPERABLE, DISCONNECTED, ALTERED OR NOT WOKING PROPERLY

20. NEVER ACTUATE THE TOOL INTO FREE SPACE

This will avoid any hazard caused by free flying fasteners and excessive strain of the tool.

21. ALWAYS ASSUME THAT THE TOOL CONTAINS FASTENERS

22. RESPECT THE TOOL AS A WORKING IMPLEMENT

23. NO HORSEPLAY

24. NEVER LOAD THE TOOL WITH FASTENERS WHEN ANY ONE OF THE OPERATING CONTROLS

(e.g., TRIGGER, CONTACT ARM) IS ACTIVATED

OBSERVE THE FOLLOWING GENERAL CAUTION IN ADDITION TO

THE OTHER WARNINGS CONTAINED IN THIS MANUAL

•

Do not use the tool as a hammer.

•

Always carry the tool by the handle, never carry the tool by the air hose.

•

The tool must be used only for the purpose it was designed.

•

Never remove, tamper with the operating controls (e.g., TRIGGER, CONTACT ARM)

•

Keep the tool in a dry place out of reach of children when not in use.

•

Do not use the tool without Safety Warning label.

•

Do not modify the tool from original design or function without approval by MAX CO., LTD.

2. SPECIFICATIONS AND TECHNICAL DATA

1. NAME OF PARTS

2. TOOL SPECIFICATIONS

PRODUCT NO. NF550/15-65

HEIGHT 12-1/2˝ (317 mm)

WIDTH 3-1/4˝ (84 mm)

LENGTH 13-5/8˝ (347 mm)

WEIGHT 4.6 lbs. (2.1 kg)

RECOMMENDED OPERATING

78 to 100 p.s.i. (5.5 to 7 bar)

PRESSURE

LOADING CAPACITY 100 staples

AIR CONSUMPTION 1.45Rat 90 p.s.i. (6 bar)

operating pressure

ACCESSORIES Hex. bar wrench, Contact tip

Frame

Cylinder Cap

Driver Guide

Magazine

Trigger

3. FASTENER SPECIFICATIONS

2-1/4"

(57mm)

(50mm)

1-3/4"

(45mm)

1-1/2"

(38mm)

1-1/4"

(32mm)

2-1/2"

(65mm)

1.75mm

Brad nails

Wire gauge: 15

TOOL AIR FITTINGS:

This tool uses a 1/4˝ N.P.T. male plug. The inside diameter should be .28˝ (7mm) or larger. The fitting must be capable of

discharging tool air pressure when disconnected from the air supply.

RECOMMENDED OPERATING PRESSURE:

78 to 100 p.s.i. (5.5 to 7 bar). Select the operating air pressure within this range for best fastener performance.

DO NOT EXCEED 120 p.s.i. (8 bar).

4. TECHNICAL DATA

NOISE

A-weighted single-event sound power level ------ LWA, 1s, d 92.02 dB

A-weighted single-event emission sound pressure level at work station ------ L p A , 1s, d 81.50 dB

These values are determined and documented in accordance to EN12549 : 1999.

VIBRATION

Vibration characteristic value ＝3.40 m/s

These values are determined and documented in accordance to ISO 8662-11.

This value is a tool-related characteristic value and does not represent the influence to the hand-arm-system when using the tool.

An influence to the hand-arm-system when using the tool will for example depend on the gripping force, the contact pressure

force, the working direction, the adjustment of mains supply, the workpiece, the workpiece support.

5. APPLICATIONS

＊Door and window casings

＊Penel assembly and moldings

＊Furniture assembly including drawer assembly, case back nailing

＊Cabinet assembly

＊Interior and exterior triming

WARNING:

3. AIR SUPPLY AND CONNECTIONS

Read section titled “SAFETY INSTRUCTIONS”.

DO NOT USE ANY POWER SOURCE EXCEPT AN AIR COMPRESSOR

The tool is designed to operate on compressed air. Do not operate the tool on any other highpressure

gas, combustible gases (e.g., oxygen, acetylene, etc.) since there is the danger of an explosion. For this

reason, absolutely do not use anything other than an air compressor to operate the tool.

OPERATE WITHIN THE PROPER AIR PRESSURE RANGE

The tool designed to operate within an air pressure range of 78 to 100 p.s.i. (5.5 to 7 bar).

The pressure should be adjusted to the type of the work being fastened. The tool shall never be

operated when the operating pressure exceeds 120 p.s.i. (8 bar).

DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE

Never operate the tool near a flammable substance (e.g., thinner, gasoline, etc.). Volatile fumes from

these substances could be drawn into the compressor and compressed together with the air and this

could result in an explosion.

DO NOT USE A WRONG FITTINGS

The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is

used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener

even after the air line is disconnected, possibly causing injury.

DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE WHEN THE TOOL IS NOT IN USE

Always disconnect the air supply from the tool and empty the magazine when operation has been

completed or suspended, when unattended, moving to a different work area, adjusting, disassembling,

or repairing the tool, and when clearing a jammed fastener.

FITTINGS: Install a male plug on the tool which is free flowing and which will release

air pressure from the tool when disconnected from the supply source.

HOSES: Hose has a min. ID of 1/4˝ (6 mm) and max. length of no more than 17˝ (5

meters).

The supply hose should contain a fitting that will provide “quick disconnecting” from

the male plug on the tool.

SUPPLY SOURCE: Use only clean regulated compressed air as a power source for

the tool.

3-PIECE AIRSET (Air filter, Regulator, Oiler):

Refer to TOOL SPECIFICATIONS for setting the correct operating pressure for the

tool.

NOTE:

A filter will help to get the best performance and minimum wear from the tool because dirt and water in

the air supply are major causes of wear in the tool.

Frequent, but not excessive, lubrication is required for the best performance. Oil added thru the air line

connection will lubricate the internal parts.

100

Air compressor

[AIR SUPPLY & CONNECTIONS]

Air filter

Air hose

Oiler

Used at 78 to 100 p.s.i. (5.5 to 7 bar)

Regulator

[AIR SUPPLY & CONNECTIONS]

3-piece airset

100

WARNING:

4. INSTRUCTIONS FOR OPERATION

Read section titled “SAFETY INSTRUCTIONS”.

1. BEFORE OPERATION

Wear Safety Glasses or Goggles.

Do not connect the air supply.

Inspect screw tightness.

Check operation of the contact arm & trigger if moving smoothly.

Connect the air supply.

Check the air-leakage. (The Tool must not have the air-leakage.)

Hold the Tool with finger-off the trigger, then push the contact arm against the work-piece. (The tool

must not operate.)

Hold the Tool with contact arm free from work-piece and pull the trigger. (The Tool must not operate.)

Disconnect the air supply.

2. OPERATION

Wear safety glasses or goggles danger to the eyes always exists due to the possibility of dust being

blown up by the exhausted air or of a fastener flying up due to the improper handling of the tool. For

these reasons, safety glasses or goggles shall always be worn when operating the tool.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment

must conform to the requirements of the American National Standards Institute, ANSI Z87.1 (Council

Directive 89/686/EEC of 21 DEC. 1989) and provide both frontal and side protection.

The employer is responsible to enforce the use of eye protection equipment by the tool operator and all

other personnel in the work area.

NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

Keep hands and body away from the discharge outlet when driving the fasteners because of dangerous

of hitting the hands or body by mistake.

NAIL LOADING

Pull back the pusher.

Insert the brads into the magazine from the rear of the magazine.

Release and return the pusher.

TEST OPERATION

Adjust the air pressure at 78 p.s.i. (5.5 bar) and connect the air supply.

Without touching the trigger, depress the contact arm against the work-piece.

Pull the trigger. (The tool must fire the fastener.)

With the tool off the work-piece, pull the trigger.

Then depress the contact arm against the work-piece.

(The tool must fire the fastener.)

Adjust the air pressure as much as the lowest possible according to the diameters and length of

fastener and the hardness of work-piece.

AIR HOSE CONNECTION

Connect the air chuck to the air plug.

When connecting the air chuck, do not point the nail discharge outlet at any part

of your body or at another preson, and do not touch the trigger.

WARNING:

Air plug

Air chuck

Inhaltsverzeichnis

Andere Max Nagelpistole Handbücher

Max

Max GS732C LT Betriebsanleitung

Max

Max HA55SF-ST Betriebsanleitung

Max

Max SN883CH/34 (CE) Betriebsanleitung

Max

Max SN890CH/34 Betriebsanleitung

Max

Max SuperFramer SN883RH2 Betriebsanleitung

Max

Max CN890S Betriebsanleitung

Max

Max SuperSider CN565S2(CE) Betriebsanleitung

Max

Max PowerLite HA55SF2/18 Bedienungsanleitung

Max

Max HN50 Betriebsanleitung

Max

Max CN450R Betriebsanleitung

Max

Max GS683RH-EX Betriebsanleitung

Max

Max NF665/15 Betriebsanleitung

Max

Max SuperSider CN565S2 Betriebsanleitung

Max

Max SN883-90CH/34(CE) Betriebsanleitung

Max

Max CN80 Betriebsanleitung

Max

Max SN890CH2(CE) Installations- und Betriebshandbuch

Max

Max SN890CH/34 Betriebsanleitung

Max

Max PowerLite HN65 Bedienungsanleitung

Max

Max NF235F/18 Betriebsanleitung

Max

Max NF565/16 Betriebsanleitung

Max

Max CN55 Bedienungsanleitung

Max

Max NF665A/15 Betriebsanleitung

Max

Max PowerLite HA65Q/15-11 Bedienungsanleitung

Max

Max SuperRoofer CN445R2 Betriebsanleitung

Beliebte Nagelpistole Handbücher anderer Marken

Performance Tool

Performance Tool M643 Bedienungsanleitung

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco Fusion Technology F-35XP Bedienungsanleitung

Grizzly

Grizzly G1847 Bedienungsanleitung

Ryobi

Ryobi R18N18G Bedienungsanleitung

Black & Decker

Black & Decker 492848-00 Bedienungsanleitung

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Bedienungsanleitung

Metabo HPT

Metabo HPT NR 3690DC Bedienungsanleitung

Surtek

Surtek CN650 Abmessungen und Installationsanleitung

Makita

Makita GF600 Bedienungsanleitung

Parkside

Parkside PET 25 B1 Bedienungsanleitung

Senco

Senco AirFree 25 Bedienungsanleitung

Freeman

Freeman P50LSLW Bedienungsanleitung

Aicon PRO

Aicon PRO DAC4507 Bedienungsanleitung

Makita

Makita AN923 Bedienungsanleitung

Grizzly

Grizzly T20644 Bedienungsanleitung

Black & Decker

Black & Decker 90514937 Bedienungsanleitung