11
SAFETY GUIDELINES
10
SAFETY GUIDELINES
ELECTRICAL SAFETY
GROUNDING INSTRUCTIONS:
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This tool is equipped
with an electric cord having an equipment-grounding conductor and a grounding plug.
The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the
outlet, have the proper outlet installed by a
qualified electrician. Improper connection of the
equipment-grounding conductor can result in a risk
of electric shock. The conductor with a green outer
surface, with or without yellow stripes, is the
equipment-grounding conductor. If repair or
replacement of the electric cord or plug is
necessary, do not connect the equipment-grounding
conductor to a live terminal.
Check with a qualified electrician or service
technician if the grounding instructions are not
completely understood, or if in doubt as to whether
the tool is properly grounded. Use only three-wire
extension cords that have three-prong grounding plugs and three-pole receptacles that
accept the tool's plug, as shown in Fig. 1. Repair or replace a damaged or worn cord
immediately.
GUIDELINES FOR USING EXTENSION CORDS:
• Make sure the extension cord is in good condition. When using an extension cord, be
sure to use one that is heavy enough to carry the current that your product will draw.
An undersized cord will cause a drop in line voltage, which will result in loss of power
and overheating. The table on the next page shows the correct size to be used
according to cord length and nameplate ampere rating. When in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier the cord.
• Make sure your extension cord is properly wired and in good condition. Always
replace a damaged extension cord, or have it repaired by a qualified person before
using it. Protect your extension cords from sharp objects, excessive heat, and damp or
wet areas.
• Use a separate electrical circuit for your tools. This circuit must consist of not less than
#12 wire with a 20 A time-delayed fuse or a #14 wire with a 15 A time-delayed fuse.
Before connecting the motor to the power line, make sure the switch is in the OFF
position and the electric current is rated the same as the current stamped on the
motor nameplate. Running at a lower voltage will damage the motor.
• Use only extension cords that are intended for outdoor use. These extension cords are
identified by a marking "Acceptable for use with outdoor appliances; store indoors
while not in use." Use only extension cords having an electrical rating not less than the
rating of the product. Do not use damaged extension cords. Examine extension cord
before using and replace if damaged. Do not abuse extension cords and do not yank
on any cord to disconnect. Keep cord away from heat and sharp edges. Always
disconnect the extension cord from the receptacle before disconnecting the product
from the extension cord.
• WARNING – To reduce the risk of electrocution, keep all connections dry and off the
ground. Do not touch plug with wet hands.
CAUTION!
In all cases, verify that the outlet in question is properly
grounded. if you are not sure, have a licensed electrician
check the outlet.
WARNING!
• Use the proper extension cord. Make sure to use an
extension cord that is heavy enough to carry the current
required by the tool. An undersized cord will cause a
drop in line voltage, resulting in loss of power and
overheating of the tool.
• Use the extension cord only for intended purpose. Do
not pull the extension cord to remove it from the power
socket.
• This tool must be grounded while in use in order to
protect the operator from electric shock.
Fig. 1
Three-prong plug
Grounding prong
Properly grounded
outlet
NOTE: Recycle unwanted materials rather than disposing of
them as waste. Sort the tool and its components in specific
categories and take to the local recycling centre or dispose of
them in an environmentally safe way.
Danger! Keep hands away from blade.
model no. 055-6971-2 | contact us 1-888-670-6682
The tool is loud and the sound can cause hearing damage. Always wear
ear protection to help prevent hearing damage and loss. Failure to comply
may result in moderate injury.
USE DUST MASK:
Some dust created by sawing contains chemicals that are known to cause
cancer, birth defects or other reproductive harm. Some examples of these
chemicals come from lead-based paints; crystalline silica from bricks,
cement and other masonry products; and arsenic and chromium from
chemically treated lumber. To reduce exposure to these chemicals, work
in a well-ventilated area with approved safety equipment, such as dust
masks that are specially designed to filter out microscopic particles.
