MaxLite AR Series Bedienungsanleitung
Operating Instructions AR Series
MaxLite LED Medium Area Light
• To reduce the risk of death, personal injury or property damage from fire,
electric shock, falling parts, cuts/abrasions, and other hazards read all
warnings and instructions included with and on the fixture box and all
fixture labels.
• Before installing, servicing, or performing routine maintenance upon
this equipment, follow these general precautions.
• Commercial installation, service and maintenance of luminaires
should be performed by a qualified licensed electrician.
• DO NOT INSTALL DAMAGED PRODUCT!
• This fixture is intended to be connected to a properly installed and
grounded UL listed junction box.
WARNING:
RISK O ELECTRICALSHOCK
• Turn off electrical power at fuse or circuit breaker box before wiring fixture
to the power supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label
information.
• Make all electrical and grounded connections in accordance with the National Electrical
Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION:
RISK O INJURY
• Unit will fall if not installed properly. ollow installation instructions.
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,
servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CAUTION:
RISK O IRE
• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• MIN 75°C SUPPLY CONDUCTORS.
Models:
Example: AR60, AR100, AR140, AR210 and AR280 Series
Operating characteristics:
Operating temperature: -40°C to 55°C
Input voltage range: 100-277, 347-480V, 50/60 HZ
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
0.77”
(
2
2
®
Picture is for illustration purposes only.
Your model may vary.
General Safety Information
Page: 1
REV: 5/21/18
Installation & Operation
Straight Arm ole Mounting:
This fixture can be configured to pole and an adapter plate has been included to mount to the pole. Hole pattern on the
pole shall be in accordance with FIG.1. If there is no hole on the pole, drill holes according to the pattern in FIG.1.
Different adapters are optional, including square pole adapter, 3”round pole adapter (RPA), 4”RPA, and 5”RPA.
• Tighten the nut plate and adapter on the pole (see FIG.2).
• Insert the fixture into the adapter (see FIG.3).
• Tighten the four M8 screws on the straight arm and secure it to the adapter (see FIG.4).
• Connect the power lead properly, make wirings inside the straight arm, and tighten the arm door with
screws (see FIG.5).
• Inspect installation to ensure fixture is secure.
Operating Instructions AR Series
MaxLite LED Medium Area Light
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
Page: 2
REV: 5/21/18
Straight Arm ole Drill attern
Operating Instructions AR Series
MaxLite LED Medium Area Light
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
Page: 3
REV: 5/21/18
Installation & Operation
Straight Arm ole Mounting
(Continued):
4.26”
(108.22mm)
2.95”
(75mm)
2.54”
(64.40mm)
0.40”
(10.22mm)
2.06”
(52.40mm)
0.35”
(9.00mm)
0.77”
(19.60mm)
0
(3.50mm)
0
1
0
(15mm)
(11mm)
(7.00mm)
+ 0.30
- 0.00
+ 0.30
- 0.00
(75mm)
4.72”(120mm)
4.84” (123mm)
0.14”
(3.50mm)
0.59” (15mm)
1.93” (49mm)
(15mm)
(53mm)
(5.70mm)
0.004”
(.10mm)depth
(75mm)
(7.00mm)
+
(75mm)
(64.40mm)
(3.50mm)
1.93”
(49mm)
0.59”
(15mm)
2.08”
(53mm)
2.00”
(50.80mm)
0.22”
(5.70mm)
0.43”
(11mm)
0.24”
(6mm)
2.95”
(75mm)
0.28”
(7.00mm)
+
+ 0.20
- 0.00
4” Round ole Adaptor
Operating Instructions AR Series
MaxLite LED Medium Area Light
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
Page: 4
REV: 5/21/18
Installation & Operation
Straight Arm ole Mounting
(Continued):
0.14”
(3.50mm)
0
(12mm)
1
(46mm)
4.17”
(105.90mm)
2.5”
2.06”
(52.40mm)
0.57”
(14.44mm)
0.31”
(7.87mm)
0.47”
(12.00mm)
+ 0.30
- 0.00
4.84” (123mm)
4.72”(120mm)
0.14”
(3.50mm)
0.47”
(12mm)
1.8”
(46mm)
0.004”
(.10mm)Depth
2
2.5”
0.13”
2.06”
0
0.47”
0.14”
(3.50mm)
0
(12mm)
(46mm)
2.95”
(75mm)
2.54”
(64.40mm)
0.22”
(5.70mm)
0.24”
(6.00mm)
2.5”
(63.50mm)
0.44”
(11.30mm)
0.13”
(3.29mm)
1.81”
(46mm)
2.06”
0.28”
(7.00mm)
+ 0.30
- 0.00
+ 0.20
- 0.00
0.47”
(12.00mm)
+
5” Round ole Adaptor
Operating Instructions AR Series
MaxLite LED Medium Area Light
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
Page: 5
REV: 5/21/18
Installation & Operation (Continued)
Slipfitter Mounting:
This fixture can be configured to provide 0 to 60° both upward and downward aiming in 15° increments (see FIG.7).
• Connect the power lead properly, Make wiring connection (see WIRING) and lay the wires in the pole, insert the slipfitter
to the pole(see FIG.8).
• Tighten the four M8 bolts on the slipfitter and secure it to the pole (see FIG.9).
• To aim the fixture, loosen and adjust the M12 knuckle bolt to right angle, adjust the aim 0 to 60°both upward and
downward(see FIG.10).
• Inspect installation to ensure fixture is secure.
Trunnion Mounting:
This fixture can be configured to mount to the tenon pole or tenon adapter.
• Tighten the fixture to the tenon pole or tenon adapter by two M12 bolts (see FIG.11).
• Loosen and adjust the adjusting bolts to the right angle, and the maximum is 60°(see FIG.12).
• Make wiring connection (see WIRING),
• Inspect installation to ensure fixture is secure.
Operating Instructions AR Series
MaxLite LED Medium Area Light
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
Page: 6
REV: 5/21/18
Maintenance
The unit is designed for years with minimum care. or optimum performance, periodically clean lens
with a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or cleaners containing
abrasive agents. When cleaning the fixture, make sure you have the power turned off and do not
spray liquid cleaner directly onto the LED, or wiring.
Wiring:
CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power suppl . All units
must be individuall connected to AC suppl .
Note:
1. Verify that supply voltage is correct by comparing it to claimed voltage on the product label.
2. All Wiring inside the fixture use WAGO connector of 5 PIN, 3 PIN and 2 PIN (See FIG.13). If need to remove or replace
any component in the driver compartment, please keep the WAGO connector for future use.
3. The FIG. 14 to FIG.16 demonstrates the interior wiring of three different configurations in the driver compartment (When
need to remove or replace any component in the driver compartment, please refer to the below wiring FIG. 14 to FIG. 17
and base on the actual condition, resume using the fixture by wire connecting).
4. Disconnect the AC power supply to prevent electric shock when making wiring or installation, removing or replacing
any component in the fixture. Make sure to use WAGO connector properly to ensure proper and secure wiring, make sure
of correct wiring before restoring power supply to light up the fixture.
Operating Instructions AR Series
MaxLite LED Medium Area Light
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
Page: 7
REV: 5/21/18
Fixture wiring diagram:
3. FIG.14 is for standard wiring which includes a 10kV Surge Suppressor.
4. FIG.15 is for wiring when a photocell sensor is used.
Operating Instructions AR Series
MaxLite LED Medium Area Light
®
FIG.14
FIG.15
5. FIG.16 is for wirings when dimmable driver, surge protector, SP-211 sensor are used.
FIG.16
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
Page: 8
REV: 5/21/18
The SP-211 is a motion sensor that dims lighting from high to low
based on movement. This slim, low-profile sensor is designed for
installation inside the bottom of a light fixture body. The PIR lens
module connects to the SP-211 through a 1.30" diameter hole in
the bottom of the fixture.
The sensors use passive infrared (PIR) sensing technology that
reacts to changes in infrared energy (moving body heat) within the
coverage area. Once the sensor stops detecting movement and the
time delay elapses lights will go from high to low mode and eventually
to an O position if it is desired. Sensors must directly “see” motion
of a person or moving object to detect them, so careful consideration
must be given to sensor luminaire placement and lens selection. Avoid
placing the sensor where obstructions may block the sensor’s line
of sight.
IR Occupancy Sensor: FS -211
IR Occupancy Sensor Installation Instruction
1. Determine an appropriate mounting location inside the light fixture minimizing the electric light contribution to
the sensor’s photocell. Allow a minimum distance of 0.2" (5.1mm) from the wiring end of the sensor to the wall
of the fixture.
2. Drill a hole 1.30" (33.0mm) in diameter through the sheet metal in the bottom of the fixture.
3. Add the rubber gasket to the threaded collar, and install the sensor face down, parallel to the mounting
surface. Ensure the rubber gasket touches the inside surface of the fixture. Install the plastic nut securely
against the fixture to a torque of 25-30 in-lbs to ensure IP rating is maintained.
4. Align the locking features between the sensor and lens module and push the lens module forward until the
o-ring seals firmly. Turn the lens module clockwise to ensure it locks in place.
5. Connect wires as shown in wiring diagram.
6. Restore power from the circuit breaker.
NOTE: The Outside ixture Wall
thickness should be no greater
than 0.125"(3.18mm) for optimal
sensor mounting and security.
Operating Instructions AR Series
MaxLite LED Medium Area Light
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
Page: 9
REV: 5/21/18
Sequence of Operation
Dimming: When motion is detected within the sensor’s coverage area, the sensor sends a signal to ramp the load up
to the selectable High Mode level unless the ambient light level is higher than the selected setpoint. When no motion is
detected for the duration of the time delay setting (factory preset at 5 minutes), the lights will go to the selectable Low
Mode level based on the signal from the sensor. If desired, a cut off time delay (factory preset at 1 hour) will trigger to
eventually turn the lights O .
Non-dimming: When motion is detected within the sensor’s coverage area, the sensor sends a signal to turn the load
ON unless the ambient light level is higher than the selected setpoint. When no motion is detected for the duration of
the time delay setting (factory preset at 5 minutes), the lights will go O based on the signal from the sensor.
Dusk to dawn control: When photocell on/off is enabled, and the ambient light falls below the photocell setpoint, the
sensor ramps the load up to the selectable High Mode level. If no motion is detected for the duration of the time delay
setting (factory preset at 5 minutes), the lights will go to the selectable Low Mode level. If the cut off time delay is
disabled, the load will remain on, at High or Low level, based on motion detection, until the ambient light increases
above the photocell setpoint.
IR Occupancy Sensor: Wiring
NOTE: The SP-211 must be grounded to
ensure signal integrity, not for safety ground.
Operating Instructions AR Series
MaxLite LED Medium Area Light
®
© Copyright 2018. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 ax: 973-244-7333 Email: info@maxlite.com
Page: 10
REV: 5/21/18
Andere Handbücher für AR Series
1
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere MaxLite Außenleuchte Handbücher
MaxLite
MaxLite GL Series Bedienungsanleitung
MaxLite
MaxLite BL-CLR Series Bedienungsanleitung
MaxLite
MaxLite GL Series Bedienungsanleitung
MaxLite
MaxLite E9A19SMTR Bedienungsanleitung
MaxLite
MaxLite ARE Series Bedienungsanleitung
MaxLite
MaxLite ML4LE109S BK2 Series Bedienungsanleitung
MaxLite
MaxLite GuardMax SECS Series Bedienungsanleitung
MaxLite
MaxLite ML1E 2DAR Series Bedienungsanleitung
MaxLite
MaxLite SEC Series Bedienungsanleitung
MaxLite
MaxLite maxLED MLLWP40LED50DS 150 Series Bedienungsanleitung
Beliebte Außenleuchte Handbücher anderer Marken
LIGMAN
LIGMAN BAMBOO 3 Bedienungsanleitung
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung
urban ambiance
urban ambiance UQL1273 Bedienungsanleitung
TotalPond
TotalPond 52238 Bedienungsanleitung
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Bedienungsanleitung