Maytronics Dolphin COMM. 12 Bedienungsanleitung

COMM. 12 Robotic Pool Cleaner

8151682

User Manual

COMM. 12 Robotic Pool Cleaner |User Manual

Table of Contents

1. IMPORTANT SAFETY INSTRUCTIONS...............................................................2

2. FCC STATEMENT.......................................................................................................3

3. SPECIFICATIONS AND WATER CONDITIONS...................................................3

4. Package CONTENTS...............................................................................................3

5. ASSEMBLY INSTRUCTIONS...................................................................................4

6. DAILY OPERATION...................................................................................................5

7. REMOTE CONTROL UNIT........................................................................................6

8. CLEANING THE FILTER...........................................................................................7

COMM. 12 Robotic Pool Cleaner

User Manual

COMM. 12 Robotic Pool Cleaner |User Manual

1. IMPORTANT SAFETY INSTRUCTIONS

Take the Robotic Pool Cleaner out of the pool before allowing people to enter the pool.

When examining the Robotic Pool Cleaner, disconnect the main power supply.

Ensure that children do not attempt to access Robotic Pool Cleaner while it is operating.

Keep the Robotic Pool Cleaner out of the reach of children or persons with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction.

Only an original power cable must be used, at all times. Replaced by a Robotic Pool Cleaner

certiﬁed technician, in case of need to avoid hazard.

The unit must be connected only to a supply circuit that is protected by a ground-fault

circuit interrupter (GFCI). This GFCI should be tested on a routine basis.

To test the GFCI, push the test button. The GFCI should interrupt power.

Push the reset button. Power should be restored. If the GFCI fails to operate in this manner,

the GFCI is defective. If the GFCI interrupts power to the power unit without the test button

being pushed, a ground current may be ﬂowing, indicating the possibility of an electric

shock. Do not use the power unit. Disconnect the power unit and contact the manufacturer

for assistance.

To reduce the risk of electric shock replace damaged cord immedietely. Do not use

extension cord to connect unit to electric supply; provide a properly located outlet.

Please ensure that the following PRECAUTIONS are implemented:

Only a trained operator should operate the Robotic Pool Cleaner.

Operator should keep hands away from driving belt mechanism.

Position the Caddy and power supply at least 3.5m/12ft from pool’s edge – during

operation.

For continued protection against possible electric shock, the power supply unit should be

placed at least 11cm / 4’’ above ground.

READ AND FOLLOW ALL INSTRUCTIONS.

Please adhere strictly to the following WARNINGS:

WARNING

CAUTION

COMM. 12 Robotic Pool Cleaner |User Manual

2. FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations to this equipment not expressly approved by the party responsible for

compliance (Maytronics Ltd.) could void the user’s authority to operate the equipment.

3. SPECIFICATIONS AND WATER CONDITIONS

• Motor protection: IP 68

• Minimum depth: 0.40 m / 1.3 ft

• Maximum depth: 7 m / 22.96 ft

4. PACKAGE CONTENTS

Carefully remove all the items from the shipping box and check them against the packing list.

You should have:

• Documentation and accessories

• Un-assembled Caddy for storing and carrying the Robotic Pool Cleaner

• Robotic Pool Cleaner and floating cable

• Power supply unit assembled to the Caddy base

• Remote control unit and remote control clip

Power supply

• Input: 100-250 AC Volts

• 50-60 Hertz

• Output: <30 VDC

• IP 54

Use the Pool Cleaner in the following

water conditions only:

• Chlorine: Max 4 ppm

• pH: 7.0 - 7.8

• Temperature: 6°-35°C / 43°-95°F

• NaCl: Maximum = 5000 ppm

When lifting the Robotic Pool Cleaner, take care to prevent back injury.

Do not bury cord – locate cord to minimize abuse from lawn mowers, hedge trimmers and

other equipment.

This Robot is for use with permanently installed pools. Do not use with storable pools.

A permanently installed pool is constructed in or on the ground or in building such that it

cannot be readily disassembled for storage and reassembled to its original integrity.

SAVE THESE INSTRUCTIONS

CAUTION

COMM. 12 Robotic Pool Cleaner |User Manual

5. ASSEMBLY INSTRUCTIONS

1. Attach the Caddy handle to the Caddy base and fasten with the four screws and four nuts

provided.

2. Connect the ﬂoating cable to the power supply.

3. Connect the remote control clip to the Caddy's handle.

Caddy base

Floating cable

Remote control unit

Power supply

Main power supply cable

Remote control clip

Caddy handle

Screws and nuts (x4)

COMM. 12 Robotic Pool Cleaner |User Manual

6. DAILY OPERATION

To operate the Robotic Pool Cleaner:

1. Place the robot in the pool. Press the ON button on the power supply. The cleaning session will

begin according to the chosen cycle time.

2. At the end of the cycle time press the OFF button on the power supply.

3. Holding the ﬂoating cable, gently pull the robot upwards and towards the Caddy. As it reaches the

side of the pool, pull the cable gently until the handle emerges. Grasp the handle (not the cable),

and pull the robot out of the water.

You can use the remote control unit to drive the Robotic Pool Cleaner to the pool side where the

Caddy is located, then gently pull the cable as described above.

Make sure the ﬂoating cable is not tangled, so it can be rolled up easily and placed on the Caddy's

handle.

4. Clean the ﬁlter as needed. Before the next operating cycle, you should also clean the robot body,

brushes and driving belt area, and remove foreign objects like rubber bands and hair, etc.

5. Once a week clean the impeller area:

CAUTION

Make sure the power supply is switched o and unplugged before service.

• Remove the four screws securing the cover of the impellers using a No. 2 Philips manual

screwdriver.

• Open and remove the cover of the impellers.

• Remove foreign objects from the impellers.

• Close the cover and re-secure the four screws.

COMM. 12 Robotic Pool Cleaner |User Manual

7. REMOTE CONTROL UNIT

The remote control

unit oers two

operation modes:

automatic mode and

manual direction

control mode.

In automatic mode,

the cleaning cycle

length can be

changed.

In manual direction

mode, the robot’s

motion can be

controlled manually.

Radio reception meter

When no black lines are showing, move

closer to the power supply unit

Battery level meter

When ﬂashing, change the batteries

Manual control indicator

When ﬂashing, you are in manual direction

control mode

Cleaning cycle icons

Forward

Turn right

Turn left

Backward

On/O button

Manual/automatic select button

Set/OK button

Direction control arrows

The remote control unit enables you to manually control the Robotic Pool Cleaner, to clean those hard-

to-reach spots or places that were skipped during the standard cleaning cycle.

Manual direction control mode

1. Press the On/O button once. This puts the remote

control in manual direction mode. Use the direction

control arrows (see right) to control the movement

of the robot around the pool.

2. Press the Forward or Backward arrows to

maneuver the Robotic Pool Cleaner forwards or

backwards at a faster speed.

3. Press the Forward or Backward arrows again to

maneuver the Robotic Pool Cleaner forwards or

backwards at the standard cleaning speed.

4. To stop the Robotic Pool Cleaner, press the arrow

showing the opposite direction to the direction in

which the robot is currently moving.

5. When the robot is idle (standing still) and you press

the Turn Left or Turn Right arrows, the robot will

turn left or right by moving one belt forwards and

the other backwards.

6. If you press the Turn Left or Turn Right arrows

while the robot is driving forwards or backwards,

the robot will turn left or right by turning one belt

and stopping the other belt.

COMM. 12 Robotic Pool Cleaner |User Manual

Manual direction control mode

1. Press the On/O button once. This puts the remote

control in manual direction mode. Use the direction

control arrows (see right) to control the movement

of the robot around the pool.

2. Press the Forward or Backward arrows to

maneuver the Robotic Pool Cleaner forwards or

backwards at a faster speed.

3. Press the Forward or Backward arrows again to

maneuver the Robotic Pool Cleaner forwards or

backwards at the standard cleaning speed.

4. To stop the Robotic Pool Cleaner, press the arrow

showing the opposite direction to the direction in

which the robot is currently moving.

5. When the robot is idle (standing still) and you press

the Turn Left or Turn Right arrows, the robot will

turn left or right by moving one belt forwards and

the other backwards.

6. If you press the Turn Left or Turn Right arrows

while the robot is driving forwards or backwards,

the robot will turn left or right by turning one belt

and stopping the other belt.

8. CLEANING THE FILTER

Clean the Robotic Pool Cleaner ﬁlter after every cleaning cycle as follows:

1. Press the latch on the top of the Robotic Pool Cleaner to open the top cover.

2. Remove the ﬁlter chamber from the robot and separate its parts.

3. Wash the ﬁne ﬁlter cartridge with water pressure from the inside out.

4. Return the ﬁne ﬁlter to the ﬁlter chamber and put the chamber back in the Robotic Pool Cleaner.

5. The robot is ready for a new cleaning cycle.

Fine filter

Filter chamber

Cleaning cycle indicator

This determines the length of the cleaning cycle

Fast

4-hour cycle

Ecient (Default setting)

5-hour cycle

Extra

6-hour cycle

Note:

• After 2 minutes if no button is pressed, the remote control unit will shut down and the Robotic Pool

Cleaner will continue to work in the previous settings.

Exiting manual direction control mode and setting the automatic mode

1. To exit the manual direction control mode, press

the Manual/Automatic select button once only.

2. The digital screen will light up, and the cleaning

cycle indicator can be changed.

1. To select the chosen cleaning cycle use the Turn

Right or Turn Left arrows. When you reach the

required function press the

Set/OK button.

Press the Manual/Automatic select button and then choose the desired parameters according to the

following table:

Cover latch

8151682

www.maytronics.com

COMM. 12 Robotic Pool Cleaner

Inhaltsverzeichnis

Andere Maytronics Schwimmbadroboter Handbücher

Maytronics

Maytronics Dolphin Triton Ps Bedienungsanleitung

Maytronics

Maytronics Swash CLX Bedienungsanleitung

Maytronics

Maytronics Dolphin X40 Plus Bedienungsanleitung

Maytronics

Maytronics Dolphin Bio Suction Bedienungsanleitung

Maytronics

Maytronics Dolphin WAVE 300 XL Bedienungsanleitung

Maytronics

Maytronics Classic 4-UNI Bedienungsanleitung

Maytronics

Maytronics Dolphin WAVE 300 XL Bedienungsanleitung

Maytronics

Maytronics DOLPHIN DX4 Bedienungsanleitung

Maytronics

Maytronics Dolphin Wave Bedienungsanleitung

Maytronics

Maytronics Dolphin WAVE 50 Bedienungsanleitung

Maytronics

Maytronics Dolphin WAVE 100 Bedienungsanleitung

Maytronics

Maytronics Dolphin Skagerrak20 Bedienungsanleitung

Maytronics

Maytronics Dolphin Liberty Bedienungsanleitung

Maytronics

Maytronics BASIC 1 Bedienungsanleitung

Maytronics

Maytronics Dolphin Nautilus CC Plus Bedienungsanleitung

Maytronics

Maytronics Dolphin Explorer E30 Bedienungsanleitung

Maytronics

Maytronics Dolphin WAVE 200 XL Bedienungsanleitung

Maytronics

Maytronics PROX2 GYRO Bedienungsanleitung

Maytronics

Maytronics Dolphin S100 Bedienungsanleitung

Maytronics

Maytronics Dolphin W 20 Bedienungsanleitung

Maytronics

Maytronics 8180090 Bedienungsanleitung

Maytronics

Maytronics Dolphin Liberty Bedienungsanleitung

Maytronics

Maytronics Dolphin Supreme M5 Bedienungsanleitung

Maytronics

Maytronics Dolphin Classic 12+ Bedienungsanleitung

Beliebte Schwimmbadroboter Handbücher anderer Marken

POOLGOODS

POOLGOODS PoolGobbler Pro Bedienungsanleitung

iRobot

iRobot Verro 600 Bedienungsanleitung

Kokido

Kokido SKOOBA K535CBX/18/EU Bedienungsanleitung

SmartPool

SmartPool Robo-Kleen PLUS Bedienungsanleitung

Brilix

Brilix BARACUDA Bedienungsanleitung

Aiper

Aiper Orca 1200 Pro Bedienungsanleitung

Hayward

Hayward Navigator Pro Bedienungsanleitung

Polaris

Polaris Vac-Sweep 380 Bedienungsanleitung

Pentair

Pentair Prowler 710 Bedienungsanleitung

BWT

BWT D500 Bedienungsanleitung

Kokido

Kokido xtrovac 70 Bedienungsanleitung

Pentair

Pentair RACER Bedienungsanleitung

Pentair

Pentair REBEL 2 Bedienungsanleitung

Zodiac

Zodiac VX55 4WD Bedienungsanleitung

SmartPool

SmartPool Robo Kleen Plus Bedienungsanleitung

Steinbach

Steinbach Twin Bedienungsanleitung

STA-RITE

STA-RITE PoolShark Vacuum Bedienungsanleitung

Zodiac

Zodiac Baracuda G3 Bedienungsanleitung