MEGATRONIX TP34 Bedienungsanleitung

Megatronix –TP34 –Anti-Code Grabbing Wireless

Transponder Immobilizer Security System

Introduction

Congratulations on purchasing the Megatronix TP34 immobilizer system. This

high-tech immobilizer uses the latest in transponder technology to protect

automatically your vehicle from theft. Once installed, disarming of the

immobilizer is fully automatic and requires no action on the part of the user. It

has three points of immobilization as well as a negative armed output option.

Operation

One of the transponder tags should be attached to the key ring containing the

vehicle’s ignition key. It is important that only one tag be attached to the key

ring at any given time. The other tag should be kept separately as a spare or

attached to the vehicle’s spare set of keys.

The immobilizer will automatically search for tags for the first 60 seconds after

the driver’s door is opened or the ignition is turned on. When a correct

transponder tag is recognized, the LED will stop flashing, indicating the

immobilizer is disarmed.

The immobilizer will re-arm automatically 30 seconds after the ignition has

been turned off. During the automatic arming period, the LED will flash rapidly.

Once armed, it will commence flashing slowly.

The siren will be triggered if a correct tag is not used to disarm the system

within 15 seconds after the door is opened or if the ignition is turned on while

the system is still armed.

Emergency Override

This immobilizer is equipped with a high security emergency override system.

The override is based on a PIN (Personal Identification Number) that must be

entered through the ignition switch in the event that a tag is lost. The PIN is

entered by following the instructions below. All units when shipped have a

different PIN number with a sticker on the services card. A new PIN number is

programmable; please see Changing PIN Number further in the instructions.

To demonstrate, the override PIN number of 1-2-3-4 will be used. It is

important to read and understand the following instruction before beginning the

override procedure.

The override is based on a combination of turning the ignition on and off, and

counting the flashes from the red LED. If a mistake is made, simply start the

procedure again with the first digit.

This procedure assumes the PIN is still 1-2-3-4. Ensure no tag is in range of

receiver (ignition key).

Action

Reaction

Result

Turn ignition switch ON

LED steady glow

Turn ignition OFF and count

flashes

LED flashes

After ONE flash turn ignition ON

LED steady glow

PIN #1

Entered

Turn ignition OFF and count

flashes

LED flashes

After TWO flashes turn ignition

LED steady glow

PIN #2

Entered

Turn ignition OFF and count

flashes

LED flashes

After THREE flashes turn ignition

LED steady glow

PIN #3

Entered

Turn ignition OFF and count

flashes

LED flashes

After FOUR flashes turn ignition

LED flashes quickly

PIN #4

Entered

Leave ignition ON - Immobilizer

will override after 15 seconds

LED will extinguish

The immobilizer will remain overridden until ignition is switched ON and a valid

tag is within range of receiver (ignition key); where the LED will flash rapidly as

per auto-arming cycle.

Programming a New PIN Number

For this example we will change the PIN from 1-2-3-4 to 4-3-2-1. Ensure no tag

is in range of receiver (ignition key).

Action

Reaction

Result

Turn ignition switch On

LED steady glow

Turn ignition OFF and count

flashes

LED flashes

After ONE flash turn ignition ON

LED steady glow

PIN #1

Entered

Turn ignition OFF and count

flashes

LED flashes

After TWO flashes turn ignition

LED steady glow

PIN #2

Entered

Turn ignition OFF and count

flashes

LED flashes

After THREE flashes turn ignition

LED steady glow

PIN #3

Entered

Turn ignition OFF and count

flashes

LED flashes

After FOUR flashes turn ignition

LED flashes quickly

PIN #4

Entered

Switch ignition OFF before 5

seconds

LED flashes

At this point, the immobilizer new PIN is ready to be reprogrammed.

After FOUR flashes turn ignition

LED steady glow

Turn ignition OFF and count

flashes

LED flashes

After THREE flashes turn ignition

LED steady glow

Turn ignition OFF and count

flashes

LED flashes

After TWO flashes turn ignition

LED steady glow

Turn ignition OFF and count

flashes

LED flashes

After ONE flash turn ignition ON

LED steady glow

Within 5 seconds show valid tag

to receiver (ignition switch)

New PIN report

The immobilizer will now report the newly programmed PIN by flashing

each number in sequence, each one separated by a long flash.

Leave ignition ON until report finishes to enable new PIN

Switch ignition OFF prior to finishing report to discard new PIN and

re-enable old PIN.

It is important to record the new PIN number for future use. If a mistake is

made and the PIN cannot be remembered, enter the PIN 9-9-9-9 and then

bring one of the coded tags close to the ignition switch. This will reset the PIN

to 1-2-3-4.

Programming a New Tag to the System

This procedure assumes the PIN is still 1-2-3-4. Ensue no tag is in range of

receiver (ignition switch).

Action

Reaction

Result

Turn ignition switch On

LED steady glow

Turn ignition OFF and count

flashes

LED flashes

After ONE flash turn ignition ON

LED steady glow

PIN #1

Entered

Turn ignition OFF and count

flashes

LED flashes

After TWO flashes turn ignition

LED steady glow

PIN #2

Entered

Turn ignition OFF and count

flashes

LED flashes

After THREE flashes turn ignition

LED steady glow

PIN #3

Entered

Turn ignition OFF and count

flashes

LED flashes

After FOUR flashes turn ignition

LED flashes quickly

PIN #4

Entered

At this point, the immobilizer new tag is ready to be reprogrammed.

Within 5 seconds place tag into

receiver area (ignition switch)

LED will glow

constantly for 2

seconds –Tag is

now confirmed

Repeat step 10 for any additional

tags

NOTE: The immobilizer contains enough memory to store five tags.

When a sixth tag is programmed, the unit will cycle around and

overwrite tag #1. This feature is useful when re-programming the

system after tags are either lost or stolen.

Once LED is glowing constantly,

switch the ignition OFF. The unit

is now armed and will respond to

the new tag

LED flashes then

glows constantly

In the event that both tags are lost and the system is overridden, the

immobilizer must be brought out of override before a new transponder can be

programmed. Open the driver’s door, turn the ignition ON and then bring the

new un-coded transponder close to the ignition. Allow 30 seconds for

immobilizer to re-arm and begin programming procedure.

MEGATRONIX TP34 WIRING DIAGRAM

THE INSTALLATION OF ANTENNA

1. The antenna can be installed in the vicinity position of the ignition lock, but

do not place it too close to the ignition’s metal parts so as to get better

range as shown below:

Status LED

Black wire with Ground marker

Black wire with Green marker

Black wire with Red marker

Black wire with Yellow marker

Black wire with White marker

Black wires

System Ground

Ground 300ma Armed Output

Constant +12 Volt Input

Ignition Switch Accessory

(-) Door Circuit

Immobilization Circuit 1

Immobilization Circuit 2

Immobilization Circuit 3

LOOP

ANTENNA

Red wire

Black wire with Brown marker

(+) Siren Output

TP34

2. The antenna must be installed as an even circular shape. Do not install it

bended such as below:

3. Please place the antenna as a 90o angle with the direction of the tag how

the user usually approaches the tag’s antenna to get maximum range (5 to

6 inches) as below:

IG Lock

I.G Lock

I.G. Lock

Antenna

Correct

Wrong

(Do not place too

deep on the

metal lock)

(Do not place

too near the

metal lock)

Wrong

Correct

Effective Area

Tag

Poor Range:

Just 2 or 3 cm for 0oangle and 7 or 8 cm

for 300 angles

You can get longer

range if the tag is facing

the center of the

antenna loop while

approaching

Effective Range

接收範圍

Long Range:

12 to 15 cm for 90oangle

-----------

Antenna

Andere MEGATRONIX Autoalarmanlage Handbücher

MEGATRONIX

MEGATRONIX MEGALARM MEGA 474L Bedienungsanleitung

MEGATRONIX

MEGATRONIX TP22 Bedienungsanleitung

MEGATRONIX

MEGATRONIX MEGALARM MEGA 2000 Bedienungsanleitung

MEGATRONIX

MEGATRONIX MEGALARM MEGA 462 Bedienungsanleitung

MEGATRONIX

MEGATRONIX Megalarm MEGA 2400 Bedienungsanleitung

MEGATRONIX

MEGATRONIX KP20 Montageanleitung

MEGATRONIX

MEGATRONIX KP10 Bedienungsanleitung

MEGATRONIX

MEGATRONIX CP-633 Bedienungsanleitung

MEGATRONIX

MEGATRONIX VIKING VS474L Bedienungsanleitung

MEGATRONIX

MEGATRONIX Megalarm MEGA 2500 Bedienungsanleitung

MEGATRONIX

MEGATRONIX MEGALARM MEGA 2700 Bedienungsanleitung

MEGATRONIX

MEGATRONIX TP34 Bedienungsanleitung

MEGATRONIX

MEGATRONIX Megalarm MEGA 2500 Bedienungsanleitung

MEGATRONIX

MEGATRONIX Megalarm MEGA 2500 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung