Megger MWA300 Series Bedienungsanleitung

Safety is the responsibility of the user

Only qualiﬁed and trained personnel should operate the MWA300. Operator must read and understand this entire instruction manual prior

to operating the equipment. Operator must follow instruction manual and attend to the equipment while in use. In the event of equipment

malfunction, the unit should immediately be de-energized and returned to Megger for repair. The safety precautions herein are not intended to

replace your company’s safety procedures.

Refer to IEEE 510 - 1983, “IEEE Recommended Practices for Safety in High-Voltage and High-Power Testing” for additional information.

Read the MWA300 manual before operating equipment.

This guide is not meant to replace manual.

Connect Leads / Power / Ground

After

INT/EXT switch

set to EXT

(PC operation)

Before

Black to Low

Voltage Secondary

or Tertiary Winding

HIGH-VOLTAGE EQUIPMENT!

MWA300 Quick Start Guide

MWA300_QG_EN_V01

Red to High

Voltage

Primary Winding

Turn Instrument On, select MWA from instrument list on

PowerDB which brings up “Select a Form” box.

Select 3Ø Turns Ratio & Winding Resistance form.

This guide uses this form as an example. Allow 30-60

seconds for PC to communicate with Instrument. See

manual for any PC connection issues.

Fill out Nameplate information (minimum info listed below)

Input Desired Test Settings

At this stage, connect Test leads to transformer under test.

Note color coding and marking on leads. Match to transformer

bushing markings.

Page 2

Test dialog appears once test begins:

Winding Resistance Test –depress # to test all 3Ø’s for tap or

depress highlighted box to begin testing individual phase:

For automated winding resistance testing, MTO Test Wizard can

be used if all critical nameplate information is ﬁlled in from step

4) above.

Select and start the Ratio (TTR) Test by depressing # below.

Testing will follow Nameplate input from 4) above:

Page 3

Page 4

11 Once test begins to run for any resistance, following

screen will appear:

Controls are as follows:

i) Test Setup: allows changes to test parameters, which can be seen in step 4 above (and described in

section iv below). This button is ‘greyed out’ once testing begins or MTO instrument connection is not

established.

ii) Test Mode: enables various testing to Start, Continue, Save Results etc. as testing is conducted. This

button guides operator through testing, providing instruction for next steps.

iii) Abort/Exit: allows disruption of test and/or exiting once test is concluded.

iv) Results Graph: plots resistance results for diagnostic review. This is useful in determining that each

past result is following an expected pattern. Different OLTC tap changers develop different shaped

patterns such as V, Saw Tooth, Slope curves. Familiarity with these tap changers helps improve diagnostic

capability.

v & vi) Measured Resistance: result with color background changes using “Reading Stability + Time

for stable reading” setting as shown in section iv above. When condition is reached, background turns

green.

12 Once all tests are complete and this window closes,

results will appear on test form:

Saving Results – once test is completed, form will prompt to save result.

After name is entered, results are automatically saved as each test is

completed.

Andere Handbücher für MWA300 Series

Inhaltsverzeichnis

Andere Megger Messgerät Handbücher

Megger

Megger PQ2000 Bedienungsanleitung

Megger

Megger MIT400/2 Series Bedienungsanleitung

Megger

Megger DPM1000 Bedienungsanleitung

Megger

Megger DET10C Bedienungsanleitung

Megger

Megger Teleflex SX-1 Bedienungsanleitung

Megger

Megger Power Diagnostix ICMflex Bedienungsanleitung

Megger

Megger DCM305E Bedienungsanleitung

Megger

Megger BN-19000 Bedienungsanleitung

Megger

Megger DCM2000P Bedienungsanleitung

Megger

Megger MPQ1000 Bedienungsanleitung

Megger

Megger MJOLNER 200 Bedienungsanleitung

Megger

Megger DCM330 Bedienungsanleitung

Megger

Megger BT51 Bedienungsanleitung

Megger

Megger DLRO100E Bedienungsanleitung

Megger

Megger DCM1500S Bedienungsanleitung

Megger

Megger SmartFuse 250 Bedienungsanleitung

Megger

Megger MPQ1000 Bedienungsanleitung

Megger

Megger KF-875 Bedienungsanleitung

Megger

Megger DLRO100E Bedienungsanleitung

Megger

Megger DCM1500S Bedienungsanleitung

Megger

Megger DCM340 Bedienungsanleitung

Megger

Megger DLRO10HD Bedienungsanleitung

Megger

Megger FRAX Series Bedienungsanleitung

Megger

Megger Ducter DLRO2 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung