Meinberg IMS-LANTIME M3000 Bedienungsanleitung

MANUAL

IMS - LANTIME M3000

Modular Sync. System and

NTP Server

2nd July 2020

Meinberg Funkuhren GmbH & Co. KG

All manuals and user guides at all-guides.com

Front view (Frontansicht) IMS - LANTIME M3000

DEUTSCH

4. USB Anschluss

6. Erdungsbolzen

3. Terminal / VT100, 38400 Baud, 8N1, 9pol. D-SUB Stecker

5. Statusanzeige Lüfter 1 und Lüfter 2

2. Rändelmutter (öffnen der Front)

1. LANTIME Bedienfeldanzeige mit LC-Display, Status LEDs und

Funktionstasten

6. Grounding stud

2. Knurled nut (open front)

ENGLISCH

3. Terminal / VT100, 38400 Baud, 8N1, 9pin D-SUB connector

1. LANTIME control panel with LC-Display, Status LEDs

4. USB connector

5. Status indicators Fan 1 and Fan 2

and function keys

Intelligent Modular Synchronization

1 3 4 52 6

All manuals and user guides at all-guides.com

Rear view (Rückansicht) IMS - LANTIME M3000

3. LAN-CPU

DEUTSCH (M3000 - Basiskonfiguration)

2. GNSS Satellitenempfängermodul CLK1

1. Netzteil PWR1 (100-240 V AC / 100-200 V DC)

ENGLISH (M3000 Base Configuration)

1. Power Supply PWR1 (100-240 V AC / 100-200 V DC)

3. LAN-CPU

2. GNSS Satellite Receiver Module CLK1

1 2 3

CLK1 CLK2SCU CPUPWR1 MRI1PWR2 PWR3 PWR4 MRI2 ESI1 ESI2 IO1 IO2 IO3 IO4 IO5 IO6

SPT

PPS

10MHz

Clock

Signal

All manuals and user guides at all-guides.com

Table of Contents

1 Imprint 1

2 Important Safety Information 2

2.1 Important Safety Instructions and Protective Measures ......................... 2

2.2 Used Symbols ................................................. 3

2.3 Security during Installation ......................................... 5

2.4 Protective Conductor- / Ground-Terminal ................................. 8

2.5 Safety during Operation ........................................... 9

2.6 Safety during Maintenance ......................................... 10

2.7 Handling Batteries .............................................. 10

2.8 Cleaning and Care .............................................. 11

2.9 Prevention of ESD Damage ......................................... 11

2.10 Return of Electrical and Electronic Equipment .............................. 12

3 The Modular System LANTIME 13

4 Network Timeserver with synchronized time base 14

5 Mounting the Antenna 15

5.1 GNSS Signal Reception ........................................... 15

5.1.1 Meinberg GPS Antenna/Converter ................................ 16

5.1.2 General GNSS Antennae ...................................... 19

5.1.3 Powering up a GNSS Receiver .................................. 22

5.2 Long Wave Signal Reception ........................................ 23

5.2.1 Introduction .............................................. 23

5.2.2 Mounting and Installation of a Longwave Antenna ....................... 24

5.2.3 DCF77 / PZF Receiver ....................................... 26

5.3 Cable Types .................................................. 26

6 Quick Start 27

7 Booting the IMS-CLK receiver 28

8 Booting the Single Board Computer 29

9 Conﬁguration User Interface 30

10 The Menues in Detail 31

10.1 Root Menu ................................................... 31

11 LANTIME Web Interface 33

12 Attachment: Technical Information 35

12.1 Technical Speciﬁcations LANTIME M3000 Chassis ........................... 35

12.2 ACM - Active Cooling Module ....................................... 37

12.3 Available Modules and Connectors .................................... 38

12.4 TERMINAL (Console) ............................................ 39

12.5 USB Connector ................................................ 39

12.6 Replacement or Installation of a Hot-pluggable IMS Module ..................... 40

12.6.1 Important Hints for hot-pluggable IMS Modules ........................ 41

12.7 IMS Module Options ............................................. 42

12.7.1 Power Supply 100-240 V AC / 100-200 V DC .......................... 42

12.7.2 Power Supply 20-60 V DC ..................................... 43

12.7.3 Power Supply 10-36 V DC ..................................... 43

12.7.4 GPS Clock .............................................. 44

All manuals and user guides at all-guides.com

12.7.5 GNSS Clock ............................................. 46

12.7.6 GNS-UC Clock ........................................... 48

12.7.7 GNM Clock .............................................. 50

12.7.8 PZF Clock .............................................. 52

12.7.9 TCR Clock - Time Code Reader and Generator ......................... 53

12.7.10 RSC Switch Card .......................................... 57

12.7.11 SPT - Single Pass Through .................................... 61

12.7.12 LAN-CPU ............................................... 62

12.7.13 MRI - Standard Reference Input Signals ............................ 64

12.7.14 ESI - Telecom Synchronisation References ........................... 67

12.7.15 VSI - Video Synchronization Input Card ............................. 71

12.7.16 LNE-GbE: Network Expansion with Gigabit Support and SFP Option ........... 75

12.7.17 HPS-100: PTP / SyncE / Hardware NTP Interface ...................... 80

12.7.18 TSU V3: IEEE-1588 Time Stamp Unit .............................. 83

12.7.19 IMS PIO: PPS or 10 MHz I/O Module ............................. 85

12.7.20 CPE and BPE Output Modules (Frontend - Backend, Eurocard) .............. 87

12.7.21 LIU - Line Interface Unit ...................................... 107

12.7.22 LNO - 10 MHz Sinus Output Module .............................. 115

12.7.23 REL1000: Error Relay Module .................................. 117

12.7.24 FDM - Frequency Deviation Monitoring ............................. 120

12.7.25 SCG-U: Studio Clock Generator ................................. 122

12.7.26 SCG-B: Studio Clock Generator Balanced ........................... 124

12.7.27 VSG - Video Sync Generator ................................... 126

13 RoHS and WEEE 131

14 Declaration of Conformity 132

Date: 2nd July 2020 IMS - LANTIME M3000

All manuals and user guides at all-guides.com

1 Imprint

Meinberg Funkuhren GmbH & Co. KG

Lange Wand 9, 31812 Bad Pyrmont / Germany

Phone: + 49 (0) 52 81 / 93 09 - 0

Fax: + 49 (0) 52 81 / 93 09 - 230

Internet: https://www.meinbergglobal.com

Mail: info@meinberg.de

Date: 2020-07-02

Manual

Version: 1.24

IMS - LANTIME M3000 Date: 2nd July 2020 1

All manuals and user guides at all-guides.com

2 Important Safety Information

2.1 Important Safety Instructions and Protective Measures

The following safety instructions must be respected in all operating and installation phases of the device. Non-

observance of safety instructions, or rather special warnings and operating instructions in product manuals,

violates safety standards, manufacturer instructions and proper usage of the device. Meinberg Funkuhren shall

not be responsible for any damage arising due to non-observance of these regulations.

Depending on your device or the installed options

some information is not valid for your device.

The device satisﬁes the requirements of the following EU regulations: EMC-Directive,

Low Voltage Directive, RoHS Directive and - if applicable - the Radio Equipment Directive.

If a procedure is marked with the following signal words, you may only continue, if you have understood and

fulﬁlled all requirements. In this documentation dangers and indications are classiﬁed and illustrated as follows:

DANGER!

The signal word indicates an imminently hazardous situation with a high risk level . This notice

draws attention to an operating procedure or similar proceedings, of which a non-observance may

result in serious personal injury or death .

WARNING!

The signal word indicates a hazard with a medium risk gradient . This notice draws attention to an

operating procedure, a procedure or the like which, if not followed, can lead to serious injuries ,

possibly resulting in death .

CAUTION!

The signal word indicates a hazard with a low risk gradient . This notice draws attention to an

operating procedure, a procedure or the like which, if not followed, can lead to minor injuries .

ATTENTION!

This notice draws attention to an operating procedure, a procedure or the like which, if not followed,

can cause damage to the product or loss of important data .

2 Date: 2nd July 2020 IMS - LANTIME M3000

All manuals and user guides at all-guides.com

2 Important Safety Information

2.2 Used Symbols

The following symbols and pictograms are used in this manual. To illustrate the source of danger, pictograms

are used, which can occur in all hazard classes.

Symbol

Beschreibung / Description

IEC 60417-5031

Gleichstrom / Direct current

IEC 60417-5032

Wechselstrom / Alternating current

IEC 60417-5017

Erdungsanschluss / Earth (ground) terminal

IEC 60417-5019

Schutzleiteranschluss / Protective earth (ground) terminal

ISO 7000-0434A

Vorsicht / Caution

IEC 60417-6042

Vorsicht, Risiko eines elektrischen Schlages / Caution, risk of electric shock

IEC 60417-5041

Vorsicht, heiße Oberfläche / Caution, hot surface

IEC 60417-6056

Vorsicht, Gefährlich sich bewegende Teile / Caution, moving fan blades

IEC 60417-6172

Trennen Sie alle Netzstecker / Disconnection, all power plugs

IEC 60417-5134

Elektrostatisch gefährdete Bauteile / Electrostatic Sensitive Devices

IEC 60417-6222

Information generell / Information general

2012/19/EU

Dieses Produkt fällt unter die B2B Kategorie. Zur Entsorgung muss es an den

Hersteller übergeben werden.

This product is handled as a B2B category product. In order to secure a WEEE

compliant waste disposal it has to be returned to the manufacturer.

IMS - LANTIME M3000 Date: 2nd July 2020 3

All manuals and user guides at all-guides.com

The manuals for a product are included in the scope of delivery of the device on a USB stick. The manuals can

also be obtained via the Internet. Enter www.meinbergglobal.com into your browser, then enter the correspond-

ing device name in the search ﬁeld at the top.

This manual contains important safety instructions for the installation and operation of the

device. Please read this manual completely before using the unit.

This device may only be used for the purpose described in this manual. In particular, the given

limits of the device must be observed. The safety of the installation in which the unit is

integrated is the responsibility of the installer!

Non-observance of these instructions can lead to a reduction in the safety of this device!

Please keep this manual in a safe place.

This manual is intended exclusively for electricians or persons trained by an electrician who are familiar with

the applicable national standards and safety rules. Installation, commissioning and operation of this device may

only be carried out by qualiﬁed personnel.

4 Date: 2nd July 2020 IMS - LANTIME M3000

All manuals and user guides at all-guides.com

Inhaltsverzeichnis

Andere Meinberg Server Handbücher

Meinberg

Meinberg LANTIME M400/GPS Bedienungsanleitung

Meinberg

Meinberg IMS-M3000 Bedienungsanleitung

Meinberg

Meinberg M900 Bedienungsanleitung

Meinberg

Meinberg LANTIME/GPS Bedienungsanleitung

Meinberg

Meinberg LANTIME M100 Bedienungsanleitung

Meinberg

Meinberg LANTIME M900/GPS/LNE/RPS/BGT Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg LANTIME M600 MRS Bedienungsanleitung

Meinberg

Meinberg IMS LANTIME M3000 Bedienungsanleitung

Meinberg

Meinberg LANTIME M100 Bedienungsanleitung

Meinberg

Meinberg IMS-LANTIME-M1000 Bedienungsanleitung

Meinberg

Meinberg IMS-LANTIME M500 Bedienungsanleitung

Meinberg

Meinberg LANTIME M100 Bedienungsanleitung

Meinberg

Meinberg LANTIME M300 Bedienungsanleitung

Meinberg

Meinberg LANTIME M300/GPS Bedienungsanleitung

Meinberg

Meinberg SyncFire 1200 Bedienungsanleitung

Meinberg

Meinberg LANTIME M200/GPS Bedienungsanleitung

Meinberg

Meinberg IMS - LANTIME M3000S Bedienungsanleitung

Meinberg

Meinberg LANTIME IMS-M500 Bedienungsanleitung

Meinberg

Meinberg LANTIME/SHS/BGT Bedienungsanleitung

Meinberg

Meinberg LANTIME M100/GPS Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg LANTIME M300/TCR Bedienungsanleitung

Meinberg

Meinberg LANTIME M300 Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg IMS-M1000-S Bedienungsanleitung

Meinberg

Meinberg microSync HR100/DC Gebrauchs- und Pflegehandbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung