Meinberg LANTIME M200/GPS Bedienungsanleitung

Meinberg Radio Clocks

Lange Wand 9

31812 Bad Pyrmont, Germany

Phone: +49 (5281) 9309-0

Fax: +49 (5281) 9309-30

http://www.meinberg.de

[email protected]

LANTIME M200/GPS: Compact NTP Time Server with integrated GPS

Reference Clock

LANTIME M200 time servers can be installed to provide accurate time to small and medium sized computer

networks. This entry level time server synchronizes all systems either NTP- or SNTP-compatible utilizing a

built-in Meinberg GPS radio clock as its primary reference time source. A stable and precise oscillator is

capable of bridging interferences or a temporary loss of reception.

Important note

Produktgruppe

Key Features

- Synchronization of NTP and SNTP compatible clients

- Web based status and configuration interface [1](Demo) and console based graphical configuration

utility

- Supported networking protocols: IPv4, IPv6, HTTPS, HTTP, SSH, TELNET, SCP, SFTP, FTP,

SYSLOG, SNMP

- USB Port for installing firmware updates, locking frontpanel menu access and backup/restore of

configuration and log files

- Antenna connected with up to 300m of standard coaxial cable RG58

rev 2013.0704.1631 lantime-m200-gpsPage 1/4

Description

The GNU/Linux operating system of the LANTIMEs SBC (Single Board Computer) has been optimized to ensure a high

level of security and reliability.

A large LC display shows the state of the internal GPS receiver and the NTP subsystem. Three LEDs (green/red)

indicate the status of the three main components: Reference Time (GPS), Time Synchronization Service (NTP) and

Network (Link status). A fourth red LED is labelled ALARM and can be configured to signal any event that is covered by

the notification handling routines.

The configuration of the system can be done by using a standard web browser for accessing the extensive but

straightforward html interface. Alternatively a text based and menu driven setup utility can be started from the shell

prompt after logging into the unit via Telnet or SSH.

The security-related features of LANTIME time servers satisfy highest demands. The time synchronization data can be

reliably signed and secured by symmetric keys (MD5) and the NTP autokey procedures. This protects the clients

against manipulated time and man-in-the-middle attacks and allows them to verify that the NTP packets they received

were send by the LANTIME. Additionally the whole LANTIME configuration can be done by using encrypted channels

(e.g. SSH, HTTPS or SNMPv3). Every unused/unneeded protocol can be disabled in order to reduce possible points of

attack.

In order to support network management systems the LANTIME time servers offer an extensive SNMP interface, which

can be accessed by SNMP V1, V2.c and V3. It allows the monitoring of all relevant system parameters (including

operating system parameters, network interface statistics, detailed GPS and NTP status information as well as the

complete system configuration) and can be used to alter the LANTIME configuration via SNMP set commands, too.

LANTIME time servers are designed to be deployed in IPv6 networks, the NTP time synchronization as well as the

configuration interfaces (Web-based, SSH and SNMP) comes with IPv6 support. You can assign several IPv6

addresses and the system supports automatic configuration by IPv6 autoconf.

The LANTIME M200 GPS is equipped with a high precision "TCXO" oscillator (please check our oscillator options page

for technical specifications). The oscillator determines the holdover characteristics (e.g. when the GPS signal is

disturbed or jammed).

rev 2013.0704.1631 lantime-m200-gpsPage 2/4

Characteristics

Type of receiver 6 channel GPS C/A-code receiver

Type of antenna Remote powered [2]GPS antenna/converter unit, up to 300m distance to antenna with

RG58 and up to 700m distance with RG213 cable

Display LC-display, 2 x 40 characters, with backlight

Control elements Eight push buttons to set up basic network parameters and to change receiver settings

Status info Four bicolor LEDs showing status of:

- reference time

- time service

- network

- alarm

Network Interface RJ-45 Network Connection 10/100 MBit

Power supply Standard: 100-240 VAC

available DC variants: 100-240 VDC, 12VDC, 24VDC and 48VDC

Power consumption 20W

Universal Serial Bus (USB)

Ports 1x USB Port in rear panel:

- install firmware upgrades

- backup and restore configuration files

- copy security keys

- lock/unlock front keys

Single-Board-Computer i386 compatible 500Mhz CPU, 128 MB RAM

Operating System of the

SBC Linux with nano kernel (incl. PPSkit)

Network protocols OSI

Layer 4 (transport layer) TCP, UDP

Network protocols OSI

Layer 7 (application layer) TELNET, FTP, SSH (incl. SFTP, SCP), HTTP, HTTPS, SYSLOG, SNMP

Internet Protocol (IP) IP v4, IP v6

Network Autoconfiguration

Support IPv4: Dynamic Host Configuration Protocol - DHCP (RFC 2131)

IPv6: Autoconfiguration Networking - AUTOCONF

Network Time Protocol

(NTP) NTP v2 (RFC 1119), NTP v3 (RFC 1305), NTP v4 (RFC 5905)

SNTP v3 (RFC 1769), SNTP v4 (RFC 2030)

MD5 Authentication and Autokey Key Management

Time Protocol (TIME) Time Protocol (RFC 868)

rev 2013.0704.1631 lantime-m200-gpsPage 3/4

Daytime Protocol

(DAYTIME) Daytime Protocol (RFC 867)

IEC 61850 Synchronization of IEC 61850 compliant devices by using SNTP

Hypertext Transfer Protocol

(HTTP) HTTP/HTTPS (RC 2616)

Secure Shell (SSH) SSH v1.3, SSH v1.5, SSH v2 (OpenSSH)

Telnet Telnet (RFC 854-RFC 861)

Form Factor Desktop housing (335 x 45 x 240 mm)

Ambient temperature 0 ... 50°C / 32 ... 122°F

Humidity Max. 85%

Scope of supply Included in delivery is our [3]GPS antenna incl. converter unit, 20m GPS antenna cable

(RG58) and product documentation.

Technical Support Meinberg offers free lifetime technical support via telephone or e-mail.

Warranty Three-Year Warranty

Firmware Updates Firmware is field-upgradeable, updates can be installed directly at the unit or via a

remote network connection.

Software updates are provided free of charge, for the lifetime of your Meinberg product.

RoHS-Status of the product This product is fully RoHS compliant

WEEE status of the product This product is handled as a B2B category product. In order to secure a WEEE

compliant waste disposal it has to be returned to the manufacturer. Any transportation

expenses for returning this product (at its end of life) have to be incurred by the end

user, whereas Meinberg will bear the costs for the waste disposal itself.

Additional Information Additional information about the Meinberg LANTIME family of NTP time servers and

other LANTIME models can be found on the [4]LANTIME NTP Time Server Family Page

Manual

The english manual is available as a PDF file: [5]Download (PDF)

Links:

[1] http://www.meinberg.de/cgi-bin/main.cgi

[2] http://www.meinbergglobal.com/english/products/gps-antenna-converter.htm

[3] http://www.meinberg.de/english/products/gps-antenna-converter.htm

[4] http://www.meinberg.de/english/products/ntp-time-server.htm

[5] http://www.meinberg.de/download/docs/manuals/english/m200_gps.pdf

rev 2013.0704.1631 lantime-m200-gpsPage 4/4

Andere Handbücher für LANTIME M200/GPS

Inhaltsverzeichnis

Andere Meinberg Server Handbücher

Meinberg

Meinberg LANTIME M900/GPS/LNE/RPS/BGT Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg IMS-M4000 Bedienungsanleitung

Meinberg

Meinberg IMS-LANTIME M500 Bedienungsanleitung

Meinberg

Meinberg LANTIME M600 MRS Bedienungsanleitung

Meinberg

Meinberg LANTIME M400/GPS Bedienungsanleitung

Meinberg

Meinberg SyncFire 1500 Bedienungsanleitung

Meinberg

Meinberg IMS-LANTIME M3000 Bedienungsanleitung

Meinberg

Meinberg LANTIME/GPS Bedienungsanleitung

Meinberg

Meinberg LANTIME M150/GPS Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg IMS LANTIME M3000 Bedienungsanleitung

Meinberg

Meinberg LANTIME CPU Expansion Shelf Bedienungsanleitung

Meinberg

Meinberg IMS-M3000 Bedienungsanleitung

Meinberg

Meinberg IMS LANTIME M4000 Bedienungsanleitung

Meinberg

Meinberg IMS-LANTIME-M1000 Bedienungsanleitung

Meinberg

Meinberg M900 Bedienungsanleitung

Meinberg

Meinberg LANTIME M100 Bedienungsanleitung

Meinberg

Meinberg LANTIME M300 Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg LANTIME IMS-M500 Bedienungsanleitung

Meinberg

Meinberg SyncFire 1200 Bedienungsanleitung

Meinberg

Meinberg microSync HR100/DC Gebrauchs- und Pflegehandbuch

Meinberg

Meinberg IMS - LANTIME M3000S Bedienungsanleitung

Meinberg

Meinberg LANTIME M100 Bedienungsanleitung

Meinberg

Meinberg LANTIME M100 Bedienungsanleitung

Meinberg

Meinberg LANTIME M300/MGR Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung