MELICONI TLC02 Bedienungsanleitung
TLC02
Thank you for choosing a Meliconi remote control.
The TLC02 remote control is designed to command a LG digital television sets.
The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio
frequency (e.g. voice commands and pointers) are not supported.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
The remote control requires 2 new 1.5V AAA/LR03 alkaline batteries, not included in the
package. Insert with the correct polarity as shown in figure.
DO NOT use rechargeable batteries.
BATTERIES TEST: Press and hold the 5button and check that the LED remains on
continuously until the button is released. If the light is off or blinks, the inserted batteries are low,
therefore they need replacement.
If necessary it is possible to completely reset the remote control and bring it back to the initial conditions.
WARNING : All user settings will be lost. Operate as follows:
•On the MELICONI remote control press and hold the button until the LED lights up; release.
•Enter the code 0100.
•Three final flashes indicate that the operation has been completed successfully.
RESET THE REMOTE CONTROL
Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control
INSERTING THE BATTERIES
SAFETY WARNINGS
The remote control and batteries should not be exposed to excessive heat such as sunlight, fire
or the like.
The product is not a toy. Keep out of reach of children or domestic animals.
This remote control, after inserting the batteries, is normally ready for use as it is already set at the
factory with a specific code.
Keep this booklet for future reference
Remote control for TV sets LG ready to use
The functions of the buttons on the MELICONI remote control are only available if the original device is equipped with it.
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
To enable them, connect to the www.cme.it page, use the on-line tool BUTTONS AND FUNCTIONS and continue until you
see the list matching buttons between the original remote control and the MELICONI remote control.
To obtain some functions, press and hold the button and press the corresponding key indicated in the table.
If the function you want to play is matched with an number in orange color, operate as follows:
•On the MELICONI remote control press and hold the button.
•When the LED turn on, without releasing the button, point the remote control towards the device
and enter the previously identified number corresponding to the function you want to get. (at the last digit
pressure, the remote control already transmits this function)
• Release the buttons; to match the function obtained to a MELICONI remote control button, within 30
seconds, press and hold the desired button.
• Wait three flashes indicate that storage; release the button. (the used button loses the original function
that will be called by the REMOTE CONTROL RESET procedure)
●IF THE REMOTE CONTROL IS NEW AND YOU CAN NOT MAKE IT WORK
Check that you have carried out all the settings procedures correctly. If necessary repeat them, following all the steps
indicated carefully, or contact the ASSISTANCE.
●IF THE REMOTE CONTROL IS NO LONGER ABLE TO CONTROL THE DEVICE
Disconnect the device from the electric socket and leave it without power for a few minutes; switch the device on again.
Remove the batteries from the remote control, press the ON/OFF button twice and insert NEW batteries.
Make sure that the remote control is pointing at the device without any obstacles between them.
If necessary try to the RESET THE REMOTE CONTROL.
●IF SOME FUNCTIONS ARE NOT AVAILABLE ON THE REMOTE CONTROL
Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.
To enable them, operate as described in the BUTTONS AND FUNCTIONS chapter.
●HOW TO CHECK IF THE REMOTE CONTROL SENDS INFRARED SIGNALS
The human eye is not able to detect infrared signals; use a camera (even that of the mobile phone).
Aim the infrared LED located in front of the remote control (not the red LED above) and press and hold on the remote control
the 5button.
If you see through the camera, the LED light with short white / light blue flashes means that the remote control works and
emits infrared.
ATTENTION!
Most problems are caused by using insufficiently charged batteries.
We recommend checking and replace them as shown in the INSERTING THE BATTERIES chapter.
TROUBLESHOOTING (F.A.Q.)
BUTTONS AND FUNCTIONS
If you want to delete the function in combination with a single button, operate as follows:
•On the MELICONI remote control press and hold the button.
•When the LED turn on, without releasing the button, enter the code 1600; release the buttons.
• Within 30 seconds, press and hold the button of which you want to delete the function; wait three flashes indicating the end
of the operation, release the button. (to recall the original function RESET THE REMOTE CONTROL)
IMPORTANT! To obtain technical assistance, it is essential to indicate the BRAND and MODEL of the appliance you intend
to control and the name of the MELICONI remote control you are using.
WARRANTY: 2 year Always keep your sales receipt as proof of the validity of the product’s warranty. The warranty is
voided if the product is tampered with or used improperly.
Meliconi SpA, Via Minghetti 10 - 40057 Cadriano di Granarolo Emilia, (BO) Italy
web: www.meliconi.com email: telecomandi@meliconi.com
The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the
end of its useful life the product must be collected separately from other waste. Therefore, at the end of the
device’s life, you must take it to appropriate centres for the differentiated collection of electrical and electronic
waste, or return it to the retailer when purchasing a new device of equivalent type. Suitable differentiated
collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible
treatment and disposal, help to prevent any negative effects on the environment and health and to promote
the recycling of the materials of which the device is made.
CAUTION: Batteries must not be disassembled, thrown into fire or released into the environment. Improper
use can cause damage to the environment and health. The symbol of the bins, indicating that the batteries
should be disposed of according to current regulations; inquire on collection of spent batteries and
accumulators in force in your country.
ASSISTANCE
DELETE FUNCTION BY SINGLE BUTTON
Andere Handbücher für TLC02
1
Inhaltsverzeichnis
Andere MELICONI Fernbedienung Handbücher
MELICONI
MELICONI Control 5 500 PLUS Bedienungsanleitung
MELICONI
MELICONI TLC04 Bedienungsanleitung
MELICONI
MELICONI easytel TV+ Bedienungsanleitung
MELICONI
MELICONI TLC03 Bedienungsanleitung
MELICONI
MELICONI Personal 6+ Bedienungsanleitung
MELICONI
MELICONI Personal 4+ Bedienungsanleitung
MELICONI
MELICONI Speedy 100 plus Bedienungsanleitung
MELICONI
MELICONI Colibri 2 Bedienungsanleitung
MELICONI
MELICONI EASY 300 Bedienungsanleitung
MELICONI
MELICONI EASY 200 Bedienungsanleitung
MELICONI
MELICONI GUMBODY UNIVERSAL 5-500 - WINDOWS Bedienungsanleitung
MELICONI
MELICONI CONTROL 3-300 PLUS - WINDOWS Bedienungsanleitung
MELICONI
MELICONI Speedy 210 combo Installationsanleitung
MELICONI
MELICONI CONTROL TV 100 Bedienungsanleitung
MELICONI
MELICONI GumBody Personal 1 Bedienungsanleitung
MELICONI
MELICONI Speedy 210 combo Bedienungsanleitung
MELICONI
MELICONI Pratico 2 Bedienungsanleitung
MELICONI
MELICONI Personal 2 plus Bedienungsanleitung
MELICONI
MELICONI Personal 3 plus Installations- und Betriebshandbuch
MELICONI
MELICONI Smart4 Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
