MELICONI Speedy 210 combo Installationsanleitung
7
Keep this booklet for future reference.
Thank you for choosing a Meliconi remote control.
The Speedy 210 combo remote control can control a TV (analogue or digital) and can also simultaneously control a
decoder if one is connected to it (terrestrial or satellite).
Thanks to its combined keypad, there is no need to manually select the device to be controlled. Using Speedy 210
combo to control both devices (TV + DECODER), the light blue buttons automatically control the TV, and the dark
blue buttons control the DECODER, but it is also possible, with suitable settings, to make all of the buttons control a
single device.
The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in it.
Its ergonomic shape and soft rubber body make it easy to grip and protect the remote control if it is knocked and
dropped.
IMPORTANT: The remote control must not be exposed to excessive heat sources.
USE OF THE BUTTONS AND FUNCTIONS
The functions of the buttons described below are available only if they are on your original device.
COMBO
Selects the next programme.
Menu options confirm button
Turns down the TV volume.
Numeric keypad.
Indicator light.
Button for exiting Teletext and
returning to normal screen.
TV ON button, sometimes needed to switch on the TV.
Turns up the TV volume.
For selecting an external input sourcefor the TV.
Teletext button.
Selects the previous programme.
ON/OFF switches the TV OFF and in some cases ON.
OFF for switching off the decoder (STB).
Before using the remote control, insert the batteries and programme it.
INSERTING THE BATTERIES
The remote control requires 2 new 1.5V alkaline AAA/LR03 batteries.
Insert them as illustrated.
Try pressing a number button and check that the red light remains lit continuously
until you release the button. If the light flashes, the batteries inserted are not charged
and are about to go flat, therefore you must substitute them.
Menu options exit button
Selects digital TV and radio
I
EN
8
Do not leave flat batteries inserted, as liquid may leak and damage the remote control
The Speedy 210 combo remote control is a universal remote, so its memory contains data relating to numerous
devices of various brands available on the market.
Each original device has a specific code which must be used to set up the remote control.
Therefore, to use Speedy 210 combo you must enter the specific code for each device you want to control.
Use one of the following methods to identify the correct code and set it in your remote control:
A) - INTERNET (recommended)
B) - MOBILE PHONE (SMS)
C) - MANUAL SEARCH
SETTING THE CODE
If you have an Internet connection available, follow the on-line guide on the www.meliconi.com/guida website to
identify the specific codes for the devices you want to control. Then set the codes manually in your MELICONI remote
control as described in the ENTERING THE CODE DIRECTLY procedure.
SETTING CODES USING INTERNET
From today, MELICONI gives customers who don’t have internet access the chance to receive the codes for
programming their remote control directly on their mobile phone.
SETTING CODES USING A MOBILE PHONE
(the service is fee, the only cost being that of sending the SMS, which depends on your service operator tariffs)
Send an SMS as follows: 2C, Type, Brand, Model
Indicate the type of device to be controlled using only one of the following
abbreviations: TV
SAT (satellite decoder)
TER (terrestrial decoder)
indicate the brand of the device to be controlled
indicate the model of the device to be controlled, usually shown on a label
on the back of the device (if you don’t know the model, don’t write anything
after the brand)
2C, TV, PHILIPS,
32PFL3614
EXAMPLE:
2C, TV, PHILIPS, 32PFL3614
Fixed text which must always be included
9
MANUAL CODE SEARCH
(only to be performed if the specific code could not be found)
IMPORTANT - separate the information with a comma, and be as precise as possible so that the IT system can
search the data and respond correctly.
Send the SMS to the number 0039 345 7518893 and wait for an SMS reply.
Once you have received the SMS with the list of codes, set the first code in the remote control as described in the
ENTERING THE CODE DIRECTLY section.
Place the MELICONI remote control in front of the device, which should already be ON, and press the TV or ON/OFF
STB button (depending on the device being operated). If the device does NOT switch off, try setting the next code in
the SMS list on the remote control. When the device reacts, check whether the other buttons are operating correctly
too. If they do, the remote control is ready to use. If they don’t, you are probably using an incorrect code intended
for a very similar device. At this point, ignore the SMS list and consult the MANUAL CODE SEARCH section to find a
more suitable code.
Check that the other buttons (light blue) correspond to the functions of the original remote control; if not, it is
likely that the code found is incorrect, but is used for a very similar device, therefore repeat the procedure
from point 2
C1. MANUAL SEARCH (TV)
If you want to use the Speedy 210 combo to simultaneously control two different devices (TV + DECODER) follow
procedure C1 then procedure C2.
To control a single device (DECODER), follow only procedure C2.
To control a single device (DIGITAL/ANALOGUE TV), follow procedure C3.
If the manual search for the code is successful, obtain the code in use by following the DISPLAY CODE IN USE
procedure and make a note of it inside the battery cover.
NOTE: If you don’t receive an SMS on your mobile phone or if the message says ERROR / NO CODE, it means the system
was not able to process the data you sent. Do not try sending another SMS, instead set the code using the MANUAL
CODE SEARCH procedure
.
1. Switch on the TV and select a programme
2. Simultaneously hold down the VOL + and VOL - buttons.
3. When the indicator light starts flashing, release the buttons
and briefly press the ON/OFF TV button.
4. The indicator light flashes faster; the remote control is ready
for the search.
5. Point the remote control at the TV. Slowly press and release
the ON/OFF TV button several times, stopping when the TV
is switched off (you may need to press the button several
dozen times).
6. When the device has switched off press the OK button.
Three long flashes indicate that the operation was completed
correctly.
TV
TV
OK
10
C2. MANUAL SEARCH (DECODER)
Check that the other buttons (dark blue) correspond to the functions of the original remote control; if not,it is
likely that the code found is incorrect, but is used for a very similar device, therefore repeat the procedure
from point 2.
1. Switch on the device and select a programme.
2. Simultaneously hold down the P+ and P- buttons.
3. When the indicator light starts flashing, release the
buttons and briefly press the ON/OFF STB button.
4. The indicator light flashes faster; the remote control is
ready for the search.
5. Point the remote control at the device. Slowly press and
release the ON/OFF STB button several times, stopping
when the decoder is switched off (you may need to press
the button several dozen times).
6. When the device has switched off press the OK button.
Three long flashes indicate that the operation was
completed correctly.
STB
C3. MANUAL SEARCH (DIGITAL/ANALOGUE TV)
1. Switch on the TV and select a programme.
2. Simultaneously hold down the VOL + and P+ buttons.
3. When the indicator light starts flashing, release the
buttons and briefly press the ON/OFF TV button.
4. The indicator light flashes faster; the remote control is
ready for the search.
5. Point the remote control at the TV. Slowly press and
release the ON/OFF TV button several times, stopping
when the TV is switched off (you may need to press the
button several dozen times).
6. When the TV has switched off press the OK button. Three
long flashes indicate that the operation was completed
correctly.
STB
STB
TV
TV
OK
OK
11
Check that the other buttons correspond to the functions of the original remote control; if not, it is likely that the code
found is incorrect, but is used for a very similar device, therefore repeat the procedure from point 2.
NOTE: During the search the indicator stops flashing and the remote control exits the programming mode in
the following cases:
• if for 12 seconds the button indicated is not pressed or if another button is pressed
• if the list of codes to find is terminated. If this happens, go to the www.meliconi.com website
To go to the programming mode, according to requirements, use one of the following pairs of buttons:
VOL
+
and VOL - to set the code for the TV part only - (light blue buttons)
P
+
and P - to set the code for the DECODER part only - (dark blue buttons)
VOL
+
and P
+
to set a single code and control only one device - (whole keypad)
Three long flashes indicate a correct setting. If they do not appear, repeat the procedure.
ENTERING THE CODE DIRECTLY
(only to be performed if you know the specific code to be set)
1. Switch to the programming mode by simultaneously
holding down the appropriate pair of buttons.
2. When the indicator light starts flashing, release the
buttons and immediately enter the specific code
previously found.(e.g.: 1306)
Example of TV code
If you set up the remote control using the MANUAL SEARCH procedure, obtain and make a note of the code in use
as follows:
DISPLAY CODE IN USE
1. Simultaneously hold down the VOL+ and VOL- buttons (if
you want to find the codes of analogue or digital TVs), or
P+ and P- (to find the decoder code).
2. When the indicator light starts flashing, release the
buttons and briefly press the TV/RADIO button.
3. After a pause of several seconds, the indicator light
produces four sets of flashes, spaced out, corresponding
to the code to be obtained. Count the number of flashes.
Each set of flashes corresponds to one figure in the code.
Ten flashes correspond to the figure 0. For example, for
the code 1306 the following flashes will be obtained:
TV Code Decoder Code
Make a note of the code obtained on the label on the inside of the battery cover. You may need it in future.
Code obtained = 1306
12
2 year WARRANTY
The warranty is voided if the product is tampered with or used improperly.
The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the end of its useful life the product must
be collected separately from other waste. Therefore, at the end of the device’s life, you must take it to appropriate centres for the differentiated
collection of electrical and electronic waste, or return it to the retailer when purchasing a new device of equivalent type, on a one-for-one basis. Suitable
differentiated collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible treatment and disposal, help
to prevent any negative effects on the environment and health and to promote the recycling of the materials of which the device is made. Improper
disposal of the product by the user will be subject to the sanctions in Legislative Decree No. 22/1997 (article 50 and subsequent articles of Legislative
Decree No. 22/1997).
Retailer stamp
Purchase date
Remote control model Speedy 210 combo
PROBLEM
The device does not respond and the indicator light
does not come on when a button is pressed
The device does not respond but the indicator light
comes on.
When you press a button the indicator light flashes
and the device does not respond to commands.
The remote control does not execute all commands
correctly.
SOLUTION
Make sure that the batteries are inserted correctly,
or substitute them with 2 new 1.5V alkaline AAA/
LR03 batteries.
Make sure that the batteries are new and that the
remote control is pointing at the device without any
obstacles between them.
If necessary, enter the remote control code again by
repeating the programming procedure.
Substitute the batteries, which are about to go flat.
You may be using the wrong code.
Enter the remote control settings again by repeating
the programming procedure.
TROUBLESHOOTING
If you have any questions about the new Speedy 210 combo remote control:
• carefully read this Instructions Booklet which will allow you to solve most problems
• consult our website www.meliconi.com where you will find the answers you need in the fastest, easiest way.
INFO-LINE
Andere Handbücher für Speedy 210 combo
2
Inhaltsverzeichnis
Andere MELICONI Fernbedienung Handbücher
MELICONI
MELICONI SPEEDY 110 Bedienungsanleitung
MELICONI
MELICONI Personal 6+ Bedienungsanleitung
MELICONI
MELICONI Personal 4+ Bedienungsanleitung
MELICONI
MELICONI FACILE Bedienungsanleitung
MELICONI
MELICONI GUMBODY UNIVERSAL 5 SMART Bedienungsanleitung
MELICONI
MELICONI Control 5 500 PLUS Bedienungsanleitung
MELICONI
MELICONI FACILE LIGHT Bedienungsanleitung
MELICONI
MELICONI SPEEDY 2 Bedienungsanleitung
MELICONI
MELICONI Smart4 Bedienungsanleitung
MELICONI
MELICONI TLC03 Bedienungsanleitung
MELICONI
MELICONI GumBody Universal 5 web Bedienungsanleitung
MELICONI
MELICONI Control TV.1 Bedienungsanleitung
MELICONI
MELICONI PERSONAL 3 Bedienungsanleitung
MELICONI
MELICONI SPEEDY 210 STB Bedienungsanleitung
MELICONI
MELICONI GumBody DIGITAL 2 SMART Bedienungsanleitung
MELICONI
MELICONI SENIOR 2 RC Bedienungsanleitung
MELICONI
MELICONI Fully 8.1 Bedienungsanleitung
MELICONI
MELICONI Facile 5.1 LED Bedienungsanleitung
MELICONI
MELICONI Personal 5+ Bedienungsanleitung
MELICONI
MELICONI TLC02 Bedienungsanleitung
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
