Mercia Garden Products 01DDPENT1008-V3 Gebrauchsanweisung

10x8 & 12x8 Pressure treated pent shed

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eﬀort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, wood saw, step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aﬀected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterprooﬁng treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on ﬁrm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run oﬀ for water. It is also recommended that the ﬂoor be at least 25mm above

the surrounding ground level to avoid ﬂooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Refer to the instructions pages for your speciﬁc product code

Pressure Treated Timber

Pressure treating is a chemical process which helps to protect wood against adverse weather which could

lead to rot or insect damage.

The most common chemicals used to pressure treat wood are Alkaline Copper Quaternary (ACQ),

Copper Azole (CA), and Micronized Copper Quaternary (MCQ).

Safety: Always wear gloves, eye protection and a dust mask when handling wood. Due to chemicals in

pressure treated wood, never burn its sawdust or scraps; instead dispose in a landﬁll.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

ﬁxings required

for each step use a

measuring tape.

P 2

01DDPENT1008-V3, 01DDPENT1208-V3

10x8 Overall Dimensions:

Length = 3116mm

Width = 2419mm

Height = 2115mm

Base Dimensions:

Length = 3064mm

Width = 2305mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

12x8 Overall Dimensions:

Length = 3662mm

Width = 2419mm

Height = 2115mm

Base Dimensions:

Length = 3610mm

Width = 2305mm

*OSB option only

Fascia - 12x95x2500mm QTY 4 -

SR1295-2500-PT3

Strip - QTY 7

10x8: 12x56x2500mm S1256-2500-PT3

12x8: 12x56x2144mm S1256-2144-PT3

Strip - 12x30x1684mm QTY 6

S1230-1684-PT3

Roof Block - 27x44x160mm QTY 7

F2744-160-PT3

Roof Support - 27x44x2238mm QTY 3 - F2744-2238-PT3

Eaves Frame QTY 4

10x8: 28x28x1546mm - FS2828-1546-PT3

12x8: 28x28x1819mm - FS2828-1819-PT3

T-Hinge QTY 6 - PI-07-0021

Turn Button QTY 1 - PI-07-0034

Pad Bolt QTY 1- PI-07-0035

Plastic Window Cill QTY 1- PI-08-0013

Styrene - 550x550mm QTY 2 - PI-05-0114

Door Panel

10x8 - AI-01DDPDP1490X2072-V3

12x8 - AI-01DDPDP1763X2072-V3

Window Panel

10x8 - AI-01DDPWP1490X2072-V3

12x8 - AI-01DDPWP1763X2072-V3

Plain Panel QTY 2

10x8 - AI-01DDPPP1490X1774-V3

12x8 - AI-01DDPPP1763X1774-V3

Gable Right

AI-01DDPRG2310X2080-V3

Floor QTY 2

10x8 - AI-01DDPF2305X1532-V2

12x8 - AI-01DDPF2305X1805-V2

Door QTY 2

AI-01MBMD551X1742-V2

Roof QTY 2

10x8 - PI-03-0295

12x8 - PI-03-0297

Gable Left

AI-01DDPLG2310X2080-V3

Nail Bag

50mm Screw x 59

Felt Tacks x 220

20mm Screw x 21

30mm Black Screw x 1

70mm Screw x24

40mm Screw x 12

30mm Screw x 102

There may be extra screws present in the nail bag

P 3

Please retain product label and instructions for future reference

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Step 1

Place the ﬂoor (No. 6) onto a ﬁrm and level

base upside down, ensuring the base

has suitable drainage & is free from

areas where standing water can collect.

Secure the ﬂoors together using 6x50mm

screws, ﬁxing in an alternating pattern

as shown in the illustration.

Once ﬁtted, turn the ﬂoor assembly the

right way up.

6x50mm Screws

Pre drill

hole

50mm

screw

Cut down to ﬁt

Step 2: Door panel assembly

Locate the doors (No. 7) into the door panel

and ﬁx in place using 3x T-Hinges (No. 14),

securing with 7x30mm screws.

Attach the pad bolt (No. 16) to the centre door

support and the catch to the opposite door with

10x30mm screws.

Measure between the top and bottom of the

door to the pad bolt and cut 2x (No. 9) strips

to ﬁt, secure in place with 2x20mm screws per

strip.

52x30mm Screws

4x20mm Screws

Pre drill

hole

30mm

screw 20mm

screw

Pre drill

hole

30mm

screw

Step 3: Window panel assembly

Cut 7x (No. 10) strips to 515mm and secure 4x

strips to the inside of the window gap

using 2x20mm screws per strip.

*Ensure the strips are ﬂush with the framing.

Place the plastic cill (No. 17) on top of the board

and rest the styrene (No. 18) in the window gap.

Measure the window gap and cut 1x (No. 10)

strip to ﬁt, securing in place with 3x20mm

screws. Attach the remaining 3 (No. 10) strips from

part a using 2x20mm screws per strip.

17x20mm Screws

Cut down to ﬁt

Pre drill

hole

30mm

screw

*For added weather protection ﬁt your

windows using silicone sealant around

the outside edges.

18 18

10 10 10

SILICONE

SEALANT

P 4

Please retain product label and instructions for future reference

Step 4

Place the right gable (No. 4) and

the ﬁrst plain side (No. 3) onto the

ﬂoor and ﬁx together using 3x50mm

screws

Do not secure the building to the

ﬂoor until the roof is ﬁtted.

*Ensure the plain panel sits within the gable*

3x50mm Screws

Pre drill

hole

50mm

screw

31a

Step 5

Following the same method outlined

in step 4, place the next 2 panels onto

the ﬂoor and secure in place using

6x50mm screws.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 6

Continue to follow the method

outlined in step 4. Place the

remaining gable and window

panel onto the ﬂoor and ﬁx using

9x50mm screws.

9x50mm Screws

Pre drill

hole

50mm

screw

Step 7

*If you have purchased the T&G ﬂoor and

roof option please continue to Step 8

Place a roof support bar (No. 12)

inbetween the framing on the

door side and plain side, aligning

with the top of gable. Mark the

position with a pencil.

Fix the roof blocks (No. 11) to the

door and plain panels in line with

the pencil mark and secure using

2x50mm screws per block.

Place the roof support on top of

the blocks and ﬁx in place with

2x70mm screws per side.

*Repeat this process with the

remaining roof supports and

blocks.

12x50mm Screws

6x70mm Screws

Pre drill

hole

50mm

screw 11

70mm

screw

P 5

Please retain product label and instructions for future reference

Step 8

Attach the 2x eaves frames (No. 13)

to each roof (No. 8) using 3x30mm

screws per eaves frame.

*Ensure the eaves are ﬂush to the

edges of the roof sheet.

*For T&G roof options use the same

method as stated above ensuring the

eaves framing is ﬂush with the edge

of the roof framing and screwed directly

through the eaves framing into the

roof framing and not into the T&G

boards.

12x40mm Screws

Pre drill

hole

30mm

screw

13 8

* OSB OPTION

* T&G OPTION

Step 9

Place the assembled roof panels

on to the building and secure as

shown in the illustration with

18x30mm screws

* Ensure the roofs are ﬂush with

the sides of the building.

18x30mm Screws

Pre drill

hole

30mm

screw

*If you have purchased the T&G roof and ﬂoor option ensure to ﬁx

the roof to the building using 38x70mm screws following the same

method outlined above.

Internally: Secure the roof panels together where they join using

5x50mm screws.

18x70mm Screws

5x50mm Screws

Pre drill

hole

70mm

screw 50mm

screw

Step 10

Secure the building to the

ﬂoor using 18x50mm screws.

*Ensure to screw through the framing

into the ﬂoor bearers.

18x50mm Screws

Pre drill

hole

50mm

screw

Step 11

Cut the felt into 3 sheets and lay

onto the roof.

* Ensure there is approximately

50mm of overhang around the

building.

Fix into place using 219x felt tacks

at 100mm intervals.

219xFelt Tacks

Felt

tacks

Felt size: 10x8 - 3220mm

12x8 - 3760mm

HANDLE

WITH CARE

P 6

Please retain product label and instructions for future reference

Step 12

Measure the side of the roof,

cut 2x (No. 19) fascias to size

and ﬁx in place using 3x30mm

screws.

Measure the distance between

the 2 facias at the front of the

building & cut 2x (No. 19) fascias

to match the gap. Secure to the

building using 6x30mm screws.

12x30mm Screws

Cut down to ﬁt

Pre drill

hole

30mm

screw

Step 13

Measure the gaps at the

corners of the building &

cut 6x (No. 9) strips to match.

Once cut secure to the

building using 3x30mm

screws per strip.

18x30mm Screws

Cut down to ﬁt

Pre drill

hole

30mm

screw

Step 14

Fix the last roof block (No. 11) to

the inside of the left door at the top.

Screw through the front of the door

into the block using 2x30mm screws.

*Ensure the block sits below the

door head.

Secure the turn button (No. 15) to the

block with 1x30mm black screw. Making

sure the turn button catches on the

door head.

2x30mm Screws

1x30mm Black Screws

Pre drill

hole

30mm

screw

P 7

Please retain product label and instructions for future reference

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTPRMSHDB0808DDOP-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02GARA0806-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTJER0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01COR0707-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHHP0806HGD4MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02PLAY511511-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVPN0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRO1006DD-V3 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628WKNE0304LBDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0806SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0634RANE4535FGDD2TW1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPP0705SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTGRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREEN0606SD-V5 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTGRO1208DD-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0806SDSEC-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1008DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPOT0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0510PB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03HEL1008DDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02HIDE0705-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHAX1010DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0707FGD2TW-V2 Bedienungsanleitung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung