Mercia Garden Products 03DTSHHP0806HGD4MW-V1 Bedienungsanleitung

P 1

Please retain product label and instructions for future reference

General Instructions

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

03DTSHHP0806HGD4MW-V1 & 03DTMBHP0806RFP-V1

8x6 Clover Summerhouse

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy or

extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treatment

to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions,

The base should be slightly smaller than the external measurement of the building, i.e. The cladding should overlap

the base, creating a run o for water. It is also recommended that the oor be at least 25mm above the surrounding

ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Refer to the instructions pages for your specic product code

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

P 2

Please retain product label and instructions for future reference

03DTSHHP0806HGD4MW-V1 & 03DTMBHP0806RFP-V1

Finial QTY 2

PI-04-0023

Felt

Floor Panel

AI-R11MBF1175X1753-V1

QTY 2

Back Panel

AI-S11SHPP1180X2016

QTY 2

Side Window Panel

AI-03S11SH1SFWC1094X2016

QTY 2

Plain Panel

AI-S11SHPP613X2016-V1

QTY 2

Left Roof 8Ft

AI-S11MBANGRL1213X1028-V1

QTY 2

Right Roof 8Ft

AI-S11MBANGRR1213X1028-V1

QTY 2

6Ft Roof

AI-S11MBDANGR1830X1028-V1

QTY 2

Upper Door Panel

AI-S11SHPPBF940X242-V1

QTY 1

Master Door

AI-STDHGMD475X1720-V1

QTY 1

Secondary Door

AI-STDHGPD475X1720-V1

QTY 1

12345

679

T-Hinge QTY 6

PI-07-0185

Door Handle QTY 2

PI-07-0081

Turn Button QTY 2

PI-07-0034

Press Lock QTY 1

PI-07-0162

Tower Bolt QTY 2

PI-07-0114

Roof Cap - 12x95x695mm QTY 1

SR1295-695mm

Fascia - 12x95x1920mm QTY 2

SR1295-1920mm

Cover Trim - 12x40x1970mm QTY 8

S1240-1970mm

Roof Bearer A - 44x58x985mm QTY 1

F4458-G-1025mm (2x32° CUTS)

Unequal Hinge QTY 4

PI-07-0184

Window QTY 2

AI-FW540X1132-V1

Eaves Frame - 28x28x1784mm QTY 2

FS2828-1784mm

Casement Stay QTY 2

PI-07-0007

Eaves Frame - 28x28x2406mm QTY 2

FS2828-2406mm

Front Window Panel

AI-03S11SH1FSFWC710X2016-V1

QTY 2

Building Content:

Roof Bearer B - 44x58x528mm QTY 3

F4458-G-568mm (2x32° CUTS)

Fascia - 12x95x1260mm QTY 4

SR1295-1260mm

Roof Bearer Block - 44x58x84mm QTY 3

F4458-84mm

Window Strip - 16x27x1094mm QTY 4

WC1627-1094mm

Window Strip - 16x27x500mm QTY 8

WC1627-500mm

Door Stop Frame - 28x28x940mm QTY 1

FS2828-940mm

Window Strip - 12x56x576mm QTY 2

S1256-576mm

Door Strip - 12x49x940mm QTY 1

S1249-940mm

Flat Roof Strip - 12x120x724mm QTY 1

S12120-724mm

Door Frame Strip - 12x40x1740mm QTY 2

S1240-1740mm

Door Frame Strip - 12x40x996mm QTY 1

S1240-996mm

Overall Dimensions:

Width = 2464mm

Depth = 1880mm

Height = 2584mm

Base Dimensions:

Width = 2350mm

Depth = 1753mm

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

P 3

Please retain product label and instructions for future reference

Nail Bag

There may be extra screws present in the nail bag

50mm Screw x 93

20mm Screw x 64

10mm Screw x 8

40mm Screw x 38

30mm Screw x 114

70mm Screw x 9

60mm Screw x 8

Felt Tacks x 270

Pre Assembly

Remove the transportation blocks from

the bottom of each panel before

beginning assembly.

Step 1

Parts needed - No. 20 QTY 1

No. 24 QTY 1

Secure the Door Strip (No.

24) with the edges being

ush to the Door Stop Frame

(No. 20) using 5x30mm

screws.

5 x 30mm Screws

Pre drill

hole

30mm

screw

SIDE VIEW

Step 2

Parts needed - No. 4 QTY 2

No. 11 QTY 1

No. 20 QTY 1

No. 24 QTY 1

Lay all of the required parts on to a

at level surface and x the Upper

Door Panel (No. 11) in the centre of

the two Front Window Panels (No.

4) with 3x50mm screws per side.

The Upper Door Panel should be

ush with the top of the left and

right Panels.

Fix the (already assembled in the

Step 1.) Door Strip (No. 24) and the

Door Stop Frame (No. 20) to the

bottom of the Front Window Panels

(No. 4) with 2x50mm screws per

side. The Door Stop Frame should

be ush with the bottom framing of

the Front Window Panels (No. 4).

10 x 50mm Screws

Pre drill

hole

50mm

screw

411 4

P 4

Please retain product label and instructions for future reference

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Step 3

Parts needed - No. 4 QTY 2

No. 9 QTY 1

No. 10 QTY 1

No. 36 QTY 6

Fix the Secondary Door (No. 10) to

the Front Window Panel (No. 4).

Secure the T-hinges (No. 36) to the

Front Window Panel (No. 4) with

3x30mm screws per hinge.

Then x the T-hinges (No. 36) to

the door with 3x30mm screws per

hinge.

Repeat the process for the Master

Door (No. 9)

36 x 30mm Screws

36 36

Pre drill

hole

30mm

screw

secondary Door Master Door

Step 4

Parts needed - No. 1 QTY 2

Secure the oors (No. 1) together

using 8x50mm screws through the

oor bearers in an alternating

pattern.

Place the assembled oor panels

(No. 1) onto a rm and level base.

Ensure the base has suitable drain-

age, free from areas where stand-

ing water can collect.

8x50mm Screws

Pre drill

hole

50mm

screw

Please retain product label and instructions for future reference

P 5

Step 5

Parts needed - No. 3 QTY 2

No. 5 QTY 2

Fix the Side Window Panel (No. 3)

and the Plain Panel (No. 5) togeth-

er by screwing through the fram-

ing using 5x50mm screws.

Ensure to stagger screws to avoid

colliding.

Repeat this with the second Side

Window Panel and the Plain Panel

but the opposite way round, as

shown in the diagram.

10x50mm Screws

Pre drill

hole

50mm

screw

**Please note that when you

x the Plain Panel (No. 5) to the

second Side Window Panel (No. 3),

this is to be tted to the opposite

side.

Step 6

Parts needed - No. 2 QTY 1

No. 3 QTY 1

No. 5 QTY 1

Place the Back Panel (No. 2) the

Plain Panel (No. 5) with the

Window Side Panel (No. 3) (that

was assembled with in Step 5.) into

position and x together with

3x50mm screws.

**Do not secure to the Floor until

the Roof is xed in position

3x50mm Screws

Pre drill

hole

50mm

screw

Step 7

Parts needed - No. 2 QTY 1

Place the second Back Panel

(No. 2) in position and x with

6x50mm screws.

**Ensure to stagger screws to

avoid colliding.

**Do not secure to the Floor

until the Roof is xed in

position

6x50mm Screws

Pre drill

hole

50mm

screw

Please retain product label and instructions for future reference

P 6

Step 8

Parts needed - No. 3 QTY 1

No. 5 QTY 1

Place the Plain Panel (No. 5) that is

already assembled with the Side

Window Panel (No. 3) (that was

assembled with in Step 5.) in posi-

tion in a previous step and x

together with the Plain Panel (No.

5) using 3x50mm screws.

**Do not secure to the Floor until

the Roof is xed in position.

3x50mm Screws

Pre drill

hole

50mm

screw

Step 9

Parts needed - No. 4 QTY 2

Place the already assembled Door

Panel (No. 4, 9, 10 and 11). into posi-

tion and x together with the two Side

Window Panels (No. 3) 3x50mm screws

per side.

If the door has not been assembled yet,

please refer to Step 1, 2 & 3.

**Do not secure to the Floor until the

Roof is xed in position.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 10

Parts needed - No. 7 QTY 2

No. 8 QTY 2

Fix the Left and Right Roof Panels

(No. 7 & 8) together by screwing

through the framing using 4x50mm

screws per assembly.

repeat this action for the other roof

side.

Ensure to stagger screws to avoid

colliding.

8x50mm Screws

Pre drill

hole

50mm

screw

Please retain product label and instructions for future reference

P 7

Step 11

Parts needed - No. 6 QTY 2

No. 7 QTY 2

No. 8 QTY 2

No. 34 QTY 1

Roll out the Felt (No. 34) and use the Roof Panels

(No. 6, 7 & 8) as shown in the illustration so you

can accuartely cut the felt before tting.

Leave a 100mm space between each panel and

cut through the centre to create 50mm overhang

for each strip. Make sure that there is a 50mm

overhang under each panel

Measure and cut four strips of felt (No. 34) at

1600x200mm.

Measure and cut one full width strip of felt (No.

34) at 1400mm long.

Once all the pieces of felt have been cut keep

these to one side whilst you construct the roof.

1600x200mm

QTY 4

1400mm

QTY 1

100mm gap between

each panel

100mm gap between

each panel

50mm overhang

below each panel

50mm overhang

below each panel

50mm overhang

below each panel

50mm overhang

below each panel

HANDLE

WITH CARE

Step 12

Parts needed - No. 12 QTY 1

No. 13 QTY 3

Pre drill holes in the underside of

Roof Bearer A (No. 12) and all 3 of

the Roof Bearer B (No. 13) parts

with an oset position of 40mm

from each of the pointed ends in

the centre of the bearers. These

holes are going to later recieve

60mm screws.

Pre drill

hole

SIDE VIEW

UNDERNEATH VIEW

SIDE VIEW

UNDERNEATH VIEW

40mm

Step 13

Parts needed - No. 6 QTY 2

Place both 6Ft Roof Panels (No. 6)

on the oor and measure 195mm

from the top of the Framing and

mark the distance on the vertical

framing with a line.

Repeat this step for both roof 6Ft

Roof Panels (No. 6) .

195mm

Please retain product label and instructions for future reference

P 8

Step 14

Parts needed - No. 7 QTY 2

No. 8 QTY 2

Place the recently assembled roof

panels (No. 7 & 8) on the oor and measure

280mm from the top of the Framing and

mark the distance on all of the vertical

framings with a line.

If these panels have not been assembled

yet, please refer to step 10.

Repeat this step for both sets of

assembled roof panels (No. 7 & 8).

280mm

Step 15

Parts needed - No. 12 QTY 1

No. 14 QTY 3

Fix the Roof Blocks (No. 14) to Roof

Bearer A (No. 12) using 2x70mm

screws per roof block. Screw up

through the bearer into the block

using the dimensions shown.

**Place tape measure under the

bottom pointed corner and

measure and mark from this

point.

6x70mm Screws

Pre drill

hole

70mm

screw

165 471 165

471

Please retain product label and instructions for future reference

P 9

Step 16

Parts needed - No. 6 QTY 1

No. 12 QTY 1

Place one of the 6Ft Roof Panels

(No. 6) on the oor. Place the main

Roof Bearer A (No. 12) at on the

bevelled end with the pointed

corner meeting the line drawn in

Step 13.

Fix Roof Bearer A (No. 12) to the 6Ft

Roof Panels (No. 6) by using a

60mm screw in the pre drilled hole

that was made in Step 12.

1x60mm Screws

Pre drill

hole

60mm

screw

Position Roof Bearer A

up against drawn line

and x to 6Ft Roof

SIDE VIEW

VIEW FROM ABOVE

Step 17

Parts needed - No. 6 QTY 2

No. 7 QTY 1

No. 8 QTY 1

No. 12 QTY 1

No. 14 QTY 3

*The use of a step ladder is

essential to construct the roof.*

To construct the Roof,

place the previously assembled

(in Step 16) 6ft Roof Panel (No. 6)

and Roof Bearer A (No. 12) on top

of the Summer House and let the

pointed edge on the other end of

the bearer meet the line drawn (in

Step 13) on the second 6ft Roof

Panel (No. 6).

When in position, Use

1x60mm screw to x up through

the previous drilled hole (in Step

12) of the bearer into the roof

frames. The beveled end of the

bearer must be at against the

roof.

Once secure, place the third

set of roof panels (No. 7 & 8)

previously assembled (in Step 10)

onto the building as shown.

You will secure it in the next

couple of steps.

1x60mm Screws

Pre drill

hole

60mm

screw

Please retain product label and instructions for future reference

P 10

Step 18

Parts needed - No. 7 QTY 1

No. 8 QTY 1

Place the remaining set of roof

panels (No. 7 & 8) (previously

assembled in Step 10) on to the

Summer House using the same

method mentioned in the previous

step. 7

Step 19

Parts needed - No. 13 QTY 3

Secure the Roof bearer B’s (No. 13)

underneath Roof bearer A (No. 12)

using 2x60mm screws per bearer

through the previously drilled

holes (in Step 12) up into the roof

panels. Make sure that the Roof

bearer B (No. 13) parts t evenly

under the framing of the roof

panels and that the pointed

corners meet the line that was

drawn in a Step 14.

The underside of the roof should

look as shown.

6x60mm Screws

Pre drill

hole

60mm

screw

Step 20

Once all four roof sides are on the

building, pull the corners together and

secure underneath the roof as shown. Fix

using 3x50mm screws per join.

The Roof bearers may need to be

unscrewed and repositioned to ensure all

the roof panels sit level with each other.

*Roof panels will support each other if

bearers are unscrewed.

Once the panels are secure,

re-screw the bearers if necessary, and

secure the threes Roof Bearers B (No. 13)

through their centres together with the

Roof Bearer A using 3x70mm screw.

12x50mm Screws

3x70mm Screws

Pre drill

hole

50mm

screw

70mm

screw

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 8x8 Waltons Vermont Summerhouse Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTGRA0301-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHRA1008FGC42TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03OVLPBRN0705-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1208DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619PNNE0403HGDD3SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0406DDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01TDM0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634LOG174-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTSHDB0606SFD5W-V1-PEFC Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0604SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03LBRO1008-V7 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628LOG114-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRODB0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRO1006DD-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619WKNE2633LBDD1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES1008-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628LOG181-V4 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0806SDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01COMGRN0406-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634LOG209-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPOT0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 10DTDRK0806-V2 Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung