Mercia Garden Products 03HEL1008DDFW-V2 Bedienungsanleitung

123456

10 11

We strongly recommend pre drilling

holes before xing screws.

50mm Screw x36

40mm Screw x100

Felt Tacks x185

30mm Screw x125

60mm Screw x50

30mm Black Screw x2

789

80mm Screw x6

03HEL1008DDFW-V2

For domestic and family use only

Retain Instructions for future reference

Dimensions

Length = 2416mm

Width = 2436mm

Height = 2124mm

For Assistance Please

Contact Customer Care on

01636 880514

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

This building should be erected by

two people.

For ease of assembly, it is advisable to

pilot drill all screw holes and ensure

all screw heads are countersunk.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand

(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,

step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather

conditions. For the duration of heavy or extended periods of rain, swelling of the

wood panels may occur. Warping of the wood may also occur during excessive

dry spells due to an interior moisture loss. Unfortunately, these processes cannot

be avoided but can be helped. It is suggested that the outdoor building is

sprayed with water during extended periods of warm sunshine and sheltered as

much as possible during rain or snow.

Our buildings are delivered pre-treated with a water based timber treatment

however this only helps to protect during transit of your garden item. To

validate your guarantee and for better protection against weathering it is

ESSENTIAL that you treat the garden building with a wood preserver within 3

months of assembly. This will need to be re-applied annually to ensure longevity

of your building. Care must be taken when constructing the garden building

that it is not touching the ground and is on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance work and

annual treatment.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be slightly

smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also recommended

that the oor be at least 25mm above the surrounding ground level to avoid ooding.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently tested to EN71 level, we

cannot accept responsibility for your safety whilst erecting or using this product.

Before

assembly make sure you

have a suitable base

ready to erect your

building

2x Front Fascia 1650mm

Door panel Window

Gable R

Window

Gable L

Plain Side

QTY 2 Back Roof

Left

Back Roof

Right

Back

Floor

QTY 2

Slave

Door

Master

Door

4x Bottom Roof Trim 1455mm

12 4x Top Roof Trim 1510mm 13 2x Cover Trim 1783mm

14 2x Cover Trim 2059mm

15 Roof Support 2830mm QTY 3 16 2x Roof End 2960mm

17 Door Bar 1705mm 18 2x Door Beading 1711mm

Finial

23 Turn Button

QTY 2

22 Flush Hinge

QTY 6

Key Plate

Door Handle

QTY 2

Mortice Lock

Barrel Bolt

QTY 2

26 Felt

Nail Bag

x4 Rain Guard 580mm

Roof Block

QTY 6

Lrg Rain Guard - 1472mm

50mm

screw

Pre drill

hole

16x50mm screws

Remove transportation blocks

from the bottom of each panel

before beginning assembly.

Each Panel should have two

blocks.

Place floor on a firm and level

base, ensure base has suitable

drainage free from areas

where standing water can

collect. (See front page on

base requirements).

30mm

screw

Pre drill

hole

36x30mm screws

30mm

screw

Pre drill

hole

8x30mm screws

Position floor section a & b as in

diagram so that floors are flush to

each other, note that the floors do

not connect by a T&G joint.

Fix with 16x50mm screws alternate

the fixing positions along the

length of the floors.

Step 1 Floor Assembly

Pre Assembly

Join the flush hinges to the door

frames using 30mm screws. Ensure

hinges are attached using the

outer plate of the hinge.

Fit the doors to the door panel with

30mm screws making sure to use

the inner plate of the hinge.

Step 2 Door Fixings

The Mortice Lock is Reversible

Fit the mortice lock

into the recess and

fix in place with the

screws provided. Fit

the key plate to the

opposite door using

the screws provided.

Fix the door handles and the metal bar (spindle) using 8x30mm

screws. Ensure the mortice lock closes correctly. If not, remove

lock and turn the catch around using the small grub screw.

x4 Rain Guard 580mm

30mm

screw

Pre drill

hole

6x30mm screws

30mm

screw

Pre drill

hole

8x30mm screws

30mm

screw

Pre drill

hole

12x30mm screws

60mm

screw

Pre drill

hole

3x60mm screws

60mm

screw

Pre drill

hole

3x60mm screws

Fix the door bar to the inside of the

slave door using 6x30mm screws as

shown in the diagram.

Step 2 Continued...

Fit the door beading strips to the

inside of the door frame using

8x30mm screws, ensuring that they

sit flush with the frame and the

door.

Attach the tower bolts to the door

bar using 12x30mm screws.

Fix the plain side and window

gable at the corners 3x50mm

screws.

DO NOT secure to the floor until

the roof is fitted.

Step 3

Step 4

Fix the plain side and

window gable at the

corners 3x50mm screws.

60mm

screw

Pre drill

hole

6x60mm screws

40mm

screw

Pre drill

hole

20x40mm screws

40mm

screw

Pre drill

hole

8x40mm screws

40mm

screw

Pre drill

hole

28x40mm screws

40mm

screw

Pre drill

hole

80mm

screw

BUILDING A BASE

When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance work and

annual treatment.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be slightly

smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also recommended

that the oor be at least 25mm above the surrounding ground level to avoid ooding.

Step 5

Fit the door panel inbetween the

left and right window panels using

6x50mm screws.

Ensure that the door is secure

before moving into place.

Place the first back roof panel onto

the supports (making sure the roof

framing sits behind the support

bar) and secure with 20x40mm

screws as shown in the diagram.

Ensure the screws line up with the

roof support bars.

Step 7

Fix the roof bar to the supports where

they meet (inside the building) using

8x40mm screws.

*Repeat this process with the second

roof panel.

Step 6

Place the first ridge bar

inside the building and

line up with the upright

framing on each gable.

Align the back edge of the

ridge bar with the top of the

gable. Once in place mark

the position on both sides

with a pencil.

Place the roof support block

to the pencil mark and

secure in place using

2x40mm screws per block.

*Repeat this process on both sides

with the remaining roof support

bars.

Place the ridge bar(s) on top

of the attached blocks and

secure through the outside

of both gables using

2x80mm screws per side.

12x40mm Screws

12x80mm Screws

*Hint: When tting the roof bar pencil mark the centre

of the roof support bar and follow down onto the gable

at a right angle, this will give you a guide to x the

support bars in place.

40mm

screw

Pre drill

hole

12x40mm screws

30mm

screw

Pre drill

hole

24x30mm screws

Step 8

Position the roof ends onto the

roof. Ensure the tongue and groove

meet and boards sit flush together.

Attach the boards using 12x40mm

screws, ensuring the boards are

screwed into the gable framing

To secure the roof felt, sandwhich

strips on top and underneath the

roof (each side) using 24x30mm

screws.

Step 10

60mm

screw

Pre drill

hole

36x60mm screws

Secure the building to the floor using

36x60mm screws in alignment with

the floor joists.

Step 11

Fix the door handles and the metal bar (spindle) using 8x30mm

screws. Ensure the mortice lock closes correctly. If not, remove

lock and turn the catch around using the small grub screw.

Cut the felt into 3 strips (3140mm).

Roll felt across from side to side in

order as shown in the diagram,

leaving a 50mm overhang at the

front and back.

Each sheet needs a 50mm overlap.

Secure the felt in place with felt

tacks at 100mm intervals

Step 9

185 Felt Tacks

11 11

aaaaaa

40mm

screw

Pre drill

hole

10x40mm screws

30mm

screw

Pre drill

hole

12x30mm screws

2x30mm Black Screws

Pre drill

hole

Fix fascia’s into place using

4x40mm screws per board.

Fit the finial over the join between

the fascias using 2x40mm screws.

Fix cover trims using 3x30mm

screws per trim.

Step 15

Attach the turn buttons to the top

and bottom of the slave door using

2x30mm black screws.

These turn buttons help to keep

your doors straight during high

and low levels of moisture content

in the air.

Step 14

Step 12

*Hint: Silicone seal the back of

each rain guard to help reduce

water running behind.

Slave Door

Locking Door

30mm

screw

Step 15

Attach the Rain Guards

centrally above the window

using 3 x 50mm screws per

guard.

12x50mm Screws

50mm

screw

Pre drill

hole

SILICONE

SEALANT

50mm

screw

Pre drill

hole

Step 16

Secure the larger rain guard

above the doors, xing into

place using 4x50mm screws.

*ensure to screw into the

framing above door.

14x50mm Screws

*Hint: Silicone seal the back of the

rain guard to help reduce water

running behind.

SILICONE

SEALANT

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01DTOVAX1006DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products HONEYSUCKLE PLAYHOUSE Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 010VLPA0305SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 04GREEN0606SD-V5 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01BEACH-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644RANE0504FGDD2TW1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHOSBRAX0705SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644LOG213-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTTWRS0605-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0806SDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619LOG015-V4 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 8x8 Waltons Vermont Summerhouse Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0644RANE4535FGDD2TW1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0406SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04GREENLEAN0804-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628RANE0403HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA1010DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHAX0608FGD4MW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN0409SHPB-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628LOG131-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628LOG114-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products OSB APEX Gebrauchsanweisung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung