Mercia Garden Products 01DTSHAX0406SDFW-V1 Gebrauchsanweisung

**Protim Aquatan T5 (621)**

Your building has been dip treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Measure

under the

head

Measure

overall

length

Screws & Nails Bolts To identify the

xings required

for each step use a

measuring tape.

01DTSHAX0406SDFW-V1

DIP TREATED SHIPLAP APEX 4X6 SINGLE DOOR FIXED WINDOWS

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All buildings should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

For ease of assembly, you

will need a tape measure to

check dimensions of

components.

ANTI-ROT

GUARANTEE TODAY

PLEASE SCAN HERE:

P 1

Please retain product label and instructions for future reference

General Instructions

P 2

01DTSHAX0406SDFW-V1

Please retain product label and instructions for future reference

4x6 Shed

Overall Dimensions:

Width = 1972mm

Depth = 1299mm

Height = 2039mm

Base Dimensions:

Width: 1860mm

Depth: 1190mm

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Ridge Bar - 28x28x1137mm QTY 1

FS2828-1137mm

Door Block - 27x44x160mm QTY 1

F2744-160mm

Cover Strip - 40x12x1570mm QTY 4

S1240-1570mm

Fascia - 12X80x1045mm QTY 4

S1280-1045mm

Greenhouse Roof Frame - 44x27x1574mm QTY 2

F2744-G-1594mm (Angled) - Used only when attaching greenhouse to shed (See Step 17).

Greenhouse Roof Block - 44x27x410mm QTY 1

F2744-G-450mm (Angled) - Used only when attaching greenhouse to shed (See Step 19).

T-Hinge QTY 3

PI-07-0021

“L” Bracket QTY 2

PI-07-0012

Pad Bolt

PI-07-0035

**For greenhouse contents please see

instructions before beginning assembly.**

Shed Diamond Finial

QTY 2

Shed diamond Finial

Felt

PI-01-0013

50mm Screws x 52

30mm Screws x 59

20mm Screws x 8

Felt Tacks x 100

60mm Screws x 8

8x6 Greenhouse with

shed

Overall Dimensions:

Width = 1972mm

Depth = 2447mm

Height = 2039mm

Base Dimensions:

Width: 1860mm

Depth: 2397mm

10x6 Greenhouse with

shed

Overall Dimensions:

Width = 1972mm

Depth = 3030mm

Height = 2039mm

Base Dimensions:

Width: 1860mm

Depth: 2980mm

12x6 Greenhouse with

shed

Overall Dimensions:

Width = 2042mm

Depth = 3665mm

Height = 2039mm

Base Dimensions:

Width: 1860mm

Depth: 3590mm

Floor QTY 1

AI-S21MBF1190X1860-V1

Roof QTY 2

AI-S11MBOHAR1075X1217-V1

1 2 34

Door QTY 1

AI-S21FBMBZBD544X1660-V1

Door Gable QTY 1

AI-01S11SHASD2FW1808X1970-V1

Plain Side QTY 2

AI-S11SHPP1193X1571-V1

Plain Gable QTY 1

AI-01S11SHAGP1808X1970-V1

Nail Bag

There may be extra screws present in the nail bag

Turn Button QTY 2

PI-07-0034

70mm Screws x 7

P 3

Please retain product label and instructions for future reference

For assistance please contact customer care on: 01636 821215

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screw-

driver, Stanley knife, Wood saw, Step ladder, Hammer and a Drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

LOCATION FOR YOUR GARDEN BUILDING

A minimum of 60cm should be left around the perimeter of your garden building to allow access for maintenance,

annual treatment and to allow air ow around the building.

Where possible you should avoid placing your garden building underneath large trees to prevent the tree causing

damage to the building.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy

or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during

excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be

helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine

and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to prevent

the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof treat-

ment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding

should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above

the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or

using this product.

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Take care removing the blocks as to not damage

the panels. Tap with a at headed screwdriver

and hammer.

Dispose of the blocks once removed.

Place the door (No. 4) into the

door gable (No. 1) aperture,

making sure there is an equal

amount of space either side

of the door.

Once in place secure the door

to the door gable using 3x

T-hinges (No. 13) securing

each hinge into position with

7x30mm screws.

21x30mm screws.

Pre drill

hole

30mm

screw

Place the oor (No. 5) onto a

rm and level surface.

Ensure your base has suitable

drainage and is free from

areas where standing water

can collect.

Place the plain gable (No.3) and one

of the plain panels (No.2) on to the

oor and x the corners together

using 3x50mm screws.

Do not secure the building to the

oor until the roof is secured in place.

*Ensure the plain gable is tted on

the inside of the plain panel. Screw

through the plain gable framing

into the framing of the plain panel.

3x50mm screws

Pre drill

hole

50mm

screw

Step 1

Parts Needed- No.1 QTY 1

- No.4 QTY 1

- No.13 QTY 3

Step 2

Parts Needed- No.5 QTY 1

Step 3

Parts Needed- No.2 QTY 1

- No.3 QTY 1

P 4

Please retain product label and instructions for future reference

Step 4

Parts Needed- No.1 QTY 1

- No.2 QTY 1

714

Step 5

Parts Needed- No.7 QTY 1

- No.14 QTY 2

Step 6

Parts Needed- No.6 QTY 2

Pre drill

hole

50mm

screw

Place the Door gable (No.1) and one of

the plain panels (No.2) on to the oor

and x the corners together using

3x50mm screws.

Do not secure the building to the oor

until the roof is secured in place.

*Ensure the Door gable is tted on the

inside of the plain panel. Screw

through the Door gable framing into

the framing of the plain panel.

9x50mm screws

Fix the Corner Braces (No. 14) to

either end of the ridge bar (No. 7)

using 2x20mm screws per bracket.

*Ensure the corner bracesare

ush with each end of the ridge

bar.

Once in place position the ridge bar

between the gables, securing into

position using 2x30mm screws per

side.

8x20mm Screws

Pre drill

hole

20mm

screw

60mm

screw

Pre drill

hole

Place the Roof Panels (No. 6) on top of

the building making sure the framing in

the roof panels sits rmly within the

Gable Panels (No. 1 & 3) and on top of

the Ridge Bar (No. 7).

**Make sure that you have got the

roof panels the correct way round

with the recess at the top of the apex

as shown in the diagram.**

**The edges of the roof panels must

be ush with the outer cladding of the

Gable Panels (No. 1 & 3).**

From the top, x directly through the

roof panels (No. 6) and into the ridge bar

(No. 7) below using 4x60mm screws per

Roof Panel.

It is essential that the ridge bar (No. 7)

and roof panel (No. 6) framing pull

together when xed with 60mm screws.

You may require another person pushing

the ridge bar (No. 7) up

from below to achieve this.

**HINT - Follow the nailing line of the

framing on the roof panel so that you

are more likely to x into the ridge bar

below. **

8x60mm Screws

P 5

Please retain product label and instructions for future reference

Place the plain gable (No.3) and one

of the plain panels (No.2) on to the

oor and x the corners together

using 3x50mm screws.

Do not secure the building to the

oor until the roof is secured in place.

*Ensure the plain gable is tted on

the inside of the plain panel. Screw

through the plain gable framing

into the framing of the plain panel.

3x50mm screws

Once the roof has been xed into

place secure the building to the oor

using 18x50mm screws.

*Ensure to screw through the panel

framing into the oor bearers

below.

18x50mm screws

Pre drill

hole

50mm

screw

Step 8

Place a cover strip (No. 9)

at each corner of the

building & x into position

using 3x30mm screws per

strip.

Fix the Door block (No.8) to the inside

of the door, ensuring its ush to

the door framing, secure using

2x30mm screws through the

door boards and into the door

block (No.8)

14x30mm Screws

Pre drill

hole

30mm

screw

Step 9

Parts Needed- No.9 QTY 4

- No.8 QTY 1

Fix the roof to the panels on each

side using 16x50mm screws. ensure

to go through the roof and into the

panel framing below

16x50mm screws

Step 7

Pre drill

hole

50mm

screw

P 6

Please retain product label and instructions for future reference

HANDLE

WITH CARE

Felt

tacks

Cut the felt (No.17) into three strips

of 1320mm and lay onto the as shown

in the illustration.

*Ensure there is approximatley

50mm of overhanging felt around

the building.

Fix the felt into place using felt tacks

at 100mm intervals.

100x Felt Tacks

Step 10

Parts Needed- No.17 QTY 1

Step 12

Parts Needed- No.10 QTY 4

- No.16 QTY 2

*If you have purchased a Greenhouse,

avoid this step move onto Step 13*

Fix the Fascias (No.10) onto the

front and back of the building

using 3x30mm screws per Fascia

Fix the She diamond nials (No.16)

onto the cover trims using 2x30mm

screws per nial, ensuring to go

through the fascias and into the

roof

16x30mm Screws

Pre drill

hole

30mm

screw

Step 11

Parts Needed- No.15 QTY 1

- No.18 QTY 2

Pre drill

hole

30mm

screw

Screw the Pad Bolt (No.15) on

to the door (No.4) and the

retainer to the door gable (No.1)

using 10x30mm screws. Make

sure that you screw into the

framing behind.

Fix the Turn Button (No. 18) onto

the Door Gable (No. 1) using

1x30mm screw for each one.

*These turn buttons help to

keep your doors straight

during high and low levels of

moisture content in the air.*

12x30mm Screws.

P 7

Please retain product label and instructions for future reference

It is ESSENTIAL that you apply wood treat-

ment immediately after the building has

been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

**Please note: For greenhouse contents

please see instructions before beginning assembly.

Not every panel from the greenhouse will be used**

Please retain product label and instructions for future reference

Lay the base frames onto the base

as shown in the illustration.

*Ensure your framing is square

and is placed against the front

of the shed.

Secure the base frames together

at each corner using 8x70mm

screws - See greenhouse nail

bag.

8x70mm Screws

Pre drill

hole

70mm

screw

**Please note: This product can be installed with the shed

door either inside the building (internal) or outside (external).

Before beginning assembling, decide which conguration best

suits your needs and read through both sets of

instructions carefully.**

Instructions: Internal shed door option.

Window panel sizes:

4x6 Greenhouse = 1193mm

(8x6 Greenhouse with shed)

6x6 Greenhouse = 1776mm

(10x6 Greenhouse with shed)

8x6 Greenhouse = 1193mm

(12x6 Greenhouse with shed)

6x6 Greenhouse

(10x6 Greenhouse with shed)

8x6 Greenhouse

(12x6 Greenhouse with shed)

4x6 Greenhouse *Shown

(8x6 Greenhouse with shed)

Place the two small window panel

onto the base frame against the shed

and x into position using 50mm screws.

Ensure to screw through the window

panels into the framing underneath

-See greenhouse nail bag.

See greenhouse instructions

for installing glazing and for

screw quantities.

Pre drill

hole

50mm

screw

P 8

Step 12

Step 13

P 7

Please retain product label and instructions for future reference

Place the Door side panels onto the

base frame against the shed and x

into position using 50mm screws.

Ensure to screw through the window

panels into the framing underneath

-See greenhouse nail bag.

See greenhouse instructions

for installing glazing and for

screw quantities.

Pre drill

hole

50mm

screw

Attach the door gable top

to the front of the building as

shown in the illustration using

50mm screws - See greenhouse

nail bag.

See greenhouse instructions

for installing glazing and for

screw quantities.

50mm

screw

30mm

16mm

Roof sizes:

4x6 Greenhouse = 1217mm

(8x6 Greenhouse with shed)

6x6 Greenhouse = 1800mm

(10x6 Greenhouse with shed)

8x6 Greenhouse = 2385mm

(12x6 Greenhouse with shed)

6x6 Greenhouse

(10x6 Greenhouse with shed)

8x6 Greenhouse

(12x6 Greenhouse with shed)

4x6 Greenhouse *Shown

(8x6 Greenhouse with shed)

Place the window into the Roof

and secure with the Buttery

Hing into position using 6x16mm

screws and 6x30mm screws as

shown in the illustration

-See greenhouse nail bag.

See greenhouse instructions

for installing glazing and for

screw quantities.

Pre drill

hole

16mm

screw

30mm

screw

Pre drill

hole

Step 14

Step 15

Step 16

P 9

Please retain product label and instructions for future reference

P 8

P 7

Fix the casement stay to the

window using 20mm screws

as shown in the ilustration.

once in position secure the

pins to the roof framing with

20mm screws, ensuring the

stay and pins align and lock

the window - See greenhouse

nail bag.

See greenhouse instructions

for installing glazing and for

screw quantities.

Pre drill

hole

20mm

screw

Place the greenhouse roof frame(s)

against each window panel and

secure in place using 3x50mm screws

per frame, ensuring to screw

into each panel.

6x50mm Screws

Pre drill

hole

50mm

screw

Using the roof’s as a guide, mark the

position for the roof block at the top

of the shed door gable.

Once marked secure the block to the

gable using 1x70mm screw, making

sure to secure through the block into

the central upright on the door gable.

1x70mm Screws

Pre drill

hole

70mm

screw

Step 17

Step 18

Step 19

P 10

Andere Handbücher für 01DTSHAX0406SDFW-V1

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 02HON51156-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02PLAY511511-V2-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01JER0806-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644CSNE0404HGDD2SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTPOT0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRODB0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES1008-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVPN0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 05DTMBAX0103SD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA1208DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02CHY0404-V3 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0806SDSEC-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTGRO1208DD-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628LOG114-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Groundsman Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0304SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619LOG003-V5 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA0806SDFW-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01GRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628AXNE0403HGDD1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0808DDFW-V1 Bedienungsanleitung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung