Mercia Garden Products 01OVLPA1208DDFW-V1 Gebrauchsanweisung

12X8 OVERLAP APEX SHED

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips

screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of

heavy or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also

occur during excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be

avoided but can be helped. It is suggested that the outdoor building is sprayed with water during extended

periods of warm sunshine and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to

prevent the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guaran-

tee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof

treatment to prevent water ingress

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base

dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The

cladding should overlap the base, creating a run o for water. It is also recommended that the oor be at

least 25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot accept responsibility for your safety whilst

erecting or using this product.

Refer to the instructions pages for you specic product code

**Protim Aquatan T5 (621)**

Your building has been treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

01OVLPA1208DDFW-V1 & 01OVLPA1208DDFW-V1-NW

P 2

01OVLPA1208DDFW-V1 & 01OVLPA1208DDFW-V1-NW

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

01OVLPA1208DDFW-V1-NW

01OVLPA1208DDFW-V1

Overall Dimensions:

Length = 3574mm

Width = 2484mm

Height = 2121mm

Base Dimensions:

Length = 3506mm

Width = 2414mm

Building Content:

T Hinge QTY 4

PI-02-1043

Felt

23 24

L-Bracket QTY 2

PI-07-0012

Window Strip - 12x30x546mm QTY 10 (FW ONLY)

S1230-546mm

Finial QTY 2

DIAMOND SHED FINIAL

Plastic Window Cill

QTY 2

(FW ONLY)

PI-08-0013

Turn Button QTY 3

PI-07-0034

Styrene QTY 4 (FW ONLY)

PI-05-0114

27 28

U Channel QTY 1

PI-07-0013

Door Gable QTY1

AI-01OVLPDG2310X2089-V1

Plain Gable QTY 1

AI-01OVLPPG2310X2089-V1

21 34567

Plain Side QTY 2

(QTY 4 NW ONLY)

AI-01OVLPPS1567X1770-V1

Window Side QTY 2

(FW ONLY)

AI-01OVLPWS1763X1567-V1

Floor QTY 4

AI-01OVLPF1753X1175-V1

Roof QTY 4

PI-03-0229

Door QTY 2

AI-01MBDR1660X439-V1

Ridge Bar - 27x70x1735mm QTY 2

F2770-1735mm

Truss Frame - 27x44x1262mm QTY 6

F2744-1302mm (1262mm nished length)

Eaves Frame - 28x28x1775mm QTY 4

F2828-1775mm

Truss Block - 27x44x140mm QTY 6

F2744-160mm (140mm nished length)

Door Block - 28x28x140mm QTY 2

F2828-140mm

Fascia -12x60x1333mm QTY 4

S1260-1333mm

Door Strip - 12x60x1016mm QTY 1

S1260-1016mm

Door Strip - 12x60x530mm QTY 1

S1260-530mm

Cover Trim - 12x45x1575mm QTY 6

S1245-1575mm

Door Beading Strip - 12x28x1590mm QTY 2

S1228-1590mm

Floor Blocks - 28x28x400mm QTY 6

F2828-400mm

Truss Support - 27x44x450mm QTY 3

F2744-490mm (450mm nished length)

Nail Bag

30mm Screw x 92

30mm Black Screw x 3

50mm Screw x 72

40mm Screw x 130

Felt Tacks x 142

Remove transportation

blocks from the bottom

of each panel before

beginning assembly. Each

Panel should have two

blocks.

Pre Assembly

Fix the T Hinges onto the

doors and door frame as

shown. Ensure that the

screws go through the

cladding and into the

framing behind.

28x30mm screws

30mm

screw Pre drill

hole

P 3

Step 1

28x30mm screws

Place oor on rm and level base, ensure

base has suitable drainage free from areas

where water can collect. (See front page on

base requirements).

Attach the oors using 40mm screws and the

oor blocks.

Screw the oor blocks to oor using 2x40mm

screws per block screwing through the oor

into the oor blocks.

30mm

screw Pre drill

hole

Fix the corners with 50mm

screws as shown in diagram.

Position the panels so there is equal spacing

between the oor and cladding on all 4 sides

Step 2

3x50mm Screws

50mm

screw Pre drill

hole

Step 3

Fix the remaining plain side and

a window side at the corners

with 50mm screws as shown in

diagram.

6x50mm Screws

50mm

screw Pre drill

hole

Use for no

window buildings

Step 4

Fix the remaining window side

and the door gable at the

corners with 50mm screws as

shown in diagram.

9x50mm Screws

50mm

screw Pre drill

hole

P 4

Step 5

Ridge Bar Assembly

Position the two parts of the ridge

bar within the ‘U’channel and

secure from either side with 3 x

30mm screws and 4 x 30mm screws

from underneath. Secure an‘L’

bracket to either end of the ridge

bar using 2 x 30mm screws per

bracket.

18x30mm Screws

27 8

24 243

Place the roof support bar in

between the front and back panels.

Ensure the top corners of the

support bar are ush with each top

point. Secure in place using the L

Bracket on each end with 4x30mm

screws.

30mm

screw Pre drill

hole

Step 6

i)Position a truss frame to the ridge

bar sloping down towards the

building side, ensure it is central to

the middle upright of the panel. Fix

with a 50mm screw through the

ridge bar into the truss frame.

ii) Align the second truss frame with

the rst on the opposite side of the

ridge bar and x with a 50mm

screw at an angle as illustrated.

ENSURE SUPPORT BARS

ARE MANUALLY SUP-

PORTED UNTIL FIXED AT

BOTH ENDS

iii

4x50mm Screws

50mm

screw Pre drill

hole

Step 7

i) Fix the truss block to the side

panel framing with 2 x 50mm

screws. Position the block at the

top of the framing with the

angle pointing upwards into the

building, aligning the block

centrally along the join between

the side panels with one screw

in each panel.

ii) Fix the support bar to the

block using 1 x 50mm screw.

6x50mm Screws

50mm

screw Pre drill

hole

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Step 8

Fix a Truss support between the

two truss frames and x in place

using 40mm screws, ensure you

pre-drill holes before xing

together.

4x40mm Screws

40mm

screw Pre drill

hole

P 5

Step 9

Place two roof sheets ontop of the

plain gable and truss making sure

the roof sheet sits ush to the

outside edge of the plain gable

and x using 40mm screws. Before

xing the roof sheet to the truss

frame make sure the edge of the

roof sheet sits in the middle of the

truss frame then x using 40mm

screws.

28x40mm Screws

6x30mm Screws

Fix the eaves frame to the

roof sheet using 3x30mm

screws for each sheet.

30mm

screw Pre drill

hole

40mm

screw Pre drill

hole

Step 10

Place two roof sheets ontop of the

plain gable and truss making sure

the roof sheet sits ush to the

outside edge of the plain gable

and x using 40mm screws. Before

xing the roof sheet to the truss

frame make sure the edge of the

roof sheet sits in the middle of the

truss frame then x using 40mm

screws.

28x40mm Screws

6x30mm Screws

Fix the eaves frame to the

roof sheet using 3x30mm

screws for each sheet.

40mm

screw Pre drill

hole

30mm

screw Pre drill

hole

40mm

screw Pre drill

hole

Step 11

24 x 50mm Screws

Do not secure the

building to the oor

until the roof is tted.

Fix the panels onto

the oor using 50mm

screws in alignment

with the oor joists

P 6

Step 12

142 x Tacks

Cut out three strips of

3740mm felt and place

onto the roof.

Place the felt at onto the

roof in the order that is

stated on the diagram

below.

Once the sheets are laid out

x them onto the roof with

tacks 100mm apart.

HANDLE

WITH CARE

Step 13

Fit the cover trims to the

building and secure in place

with 40mm screws as

shown.

Pre drill to avoid splitting.

18x40mm Screws 16

40mm

screw Pre drill

hole

16x40mm Screws

Attatch faisca’s to the roof

leaving a slight overhang at

the top..

Fit the fascias to the roof

over the felt and secure in

place with 40mm screws as

shown.

Pre drill to avoid splitting.

21 13

40mm

screw Pre drill

hole

Step 14

P 7

Step 15

Fit the styrene sheets on top of

the window cill.

When positioning the styrene

sheets ensure there is an equal

distance between them and at

either side of the windows.

Fix the window strips to the two

pieces of framing that sit

alongside the outside edges of

the window with 3x30mm

screws for each strip.

Attach the three window strips

at either side of the windows

using 3x30mm screws each.

Make sure the screws enter the

framing in the window panel

and not the styrene.

9x30mm Screws

30mm

screw Pre drill

hole

6x30mm Screws

30mm

screw Pre drill

hole

Place the

plastic window

cill onto the

Window Panel

and silicone in

place as shown

on both

diagrams to the

left.

Side View

Styrene

Window Cill

SILICONE

SEALANT

Step 16

Use 4x30mm Screws to x

each beading strip onto the

door gable. Ensure that the

screw is parallel with the

door frame when xing the

strip to the door gable as

shown in the close up view.

Attatch the turn button to

the top and bottom door

blocks with 1x30mm screw

for each one.

First line up the door blocks

on top of the framing of the

doors. Then x with

2x30mm screws by screwing

through the matchboard

door into the block.

8x30mm Screws

2x30mm Black Screws

6x30mm Screws

30mm

screw

Pre drill

hole

30mm

screw

P 8

Step 17

Fix the door strips to the

master door using 5x30mm

screws.

If the strips are attatched to

the slave door the doors will

not open properly.

5x30mm Screws

Use 1x30mm screw to

secure the turn button to

the master door.

1x30mm Black Screws

30mm

screw

Pre drill

hole

30mm

screw

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 0628CSNE0303HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Groundsman Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHPN1008FGC31TWSA-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1008DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0406DDNW-V Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1610DDOW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHAX0608FGD4MW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03HEL0808DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628RANE0504FGDD2TW1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01OVLPA0806SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01TDM0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628AXNE0403HGDD1SW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0604SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products Wessex 03WES0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1008DDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03DTSHHP1206HGD4MW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1208DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634LOG249-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 8x8 Waltons Vermont Summerhouse Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 05DTMBAX0103SD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03TGCORSE0408-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0806SDFW-V2 Bedienungsanleitung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung