Mercia Garden Products 01RAW1010DDOW-V1 Gebrauchsanweisung

01RAW1010DDOW-V1

N/A

Overlap

Cladding

Shiplap

Cladding

Solid Sheet

Roof

T&G Roof

Solid Sheet

Floor

T&G Floor

Fixed

Windows

Opening

Windows

10x10 Reverse apex workshop: Double doors, opening window with T&G roof & floor

For Assistance Please

Contact Customer Care on

01636 880514

2mm Drill bit

Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be erected by two

adults

For ease of assembly, it is advisable to

pilot drill all screw holes and ensure

all screw heads are countersunk.

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand

(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,

step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather

conditions. For the duration of heavy or extended periods of rain, swelling of the

wood panels may occur. Warping of the wood may also occur during excessive

dry spells due to an interior moisture loss. Unfortunately, these processes cannot

be avoided but can be helped. It is suggested that the outdoor building is

sprayed with water during extended periods of warm sunshine and sheltered as

much as possible during rain or snow.

Our buildings are pre treated with a water based treatment**; this only helps to

protect the product during transit and for upto 3 months against mould. To

validate your guarantee and ensure longevity of the product, it is ESSENTIAL the

building is treated with a wood preserver within the rst three months of

assembly and thereafter in accordance with the manufactures recommenda-

tions. Care must be taken to ensure the product is placed on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Whilst all products manufactured are made to the

highest standards of Safety and in the case of childrens

products independently tested to EN71 level, we cannot

accept responsibility for your safety whilst erecting or

using this product.

Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces

of the timber. You are strongly advised

to wear gloves when working with or

handling rough sawn timer.

**Protim Fentex E5**

Biocidal Product Regulation (EU 528/2012) Article 58 Information

Protim Fentex E2 preserved wood is a “treated article”which incorporates biocidal products.

Wood correctly preserved with Protim Fentex E2 is protected against mould in storage.

Contains: IPBC (3-iodo-2-propynyl-N-butyl carbamate) and propiconazole.

Wear gloves when handling freshly treated wood.

Avoid breathing dust when cutting treated or untreated wood.

Dispose of o-cuts responsibly – do not burn.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer

to diagrams for the base dimensions, The base should be slightly smaller than

the external measurement of the building, i.e. The cladding should overlap the

base, creating a run o for water. It is also recommended that the oor be at

least 25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Please retain product label and instructions for future reference

P 1

General Instructions

01RAW1210DDOW-V1

12x10 Reverse apex workshop: Double doors, opening window with T&G roof & floor

01RAW1610DDOW-V1

16x10 Reverse apex workshop: Double doors, opening window with T&G roof & floor

01RAW2010DDOW-V1

20x10 Reverse apex workshop: Double doors, opening window with T&G roof & floor

Refer to the instructions pages for you specic product code

1 2 3 4 5 6 7 8 9

Pre drill

hole

50mm

screw

30mm

screw

Nail Bag

50mm Screw x80

40mm Screw x54

Felt Tacks x170

16mm Screw x14

30mm Screw x93

70mm Screw x4

30mm Black Screw x18

100mm Screw x2

P 2

01RAW1010DDOW-V1

Overall Dimensions:

Length = 3114mm

Width = 3184mm

Height = 2482mm

Base Dimensions:

Length = 2980mm

Width = 3010mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Door Panel Window

Panel

Plain

Panel

Plain Gable

Right QTY 2

Plain Gable

Left QTY 2

Floor

QTY 2

Roof

QTY 2

Master

Door

Slave

Door

Window Truss

Gable Strip - 2387mm QTY 2

Cover Strip - 1757mm QTY 11

Door Strip - 1600mm QTY 2

Gable Block QTY 2

Truss Block QTY 2

Gable Board QTY 2

T-Hinge QTY 6

Rim Lock

Butt Hinge QTY 2

Finial QTY 2

Casement Stay

Felt

Tower Bolt QTY 2

Pre Assembly

Remove the transportation blocks

from the bottom of each panel before

assembling the building.

Step 1

Place the left and right gable sections

onto a rm and level surface next to

each other, ensuring the panels are

level top and bottom, then x

together using 12x50mm screws.

*Stagger the screws so as not to

collide.

Turn the assembled gable section

over and secure the gable board in

place with 3x30mm screws.

*Make sure to screw through into

the framing, pre-drilling to avoid

splitting the board.

24x50mm Screws

6x30mm Screws

10 11 12

Pre drill

hole

40mm

screw

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

P 3

Please retain product label and instructions for future reference

Step 2

Place the oor onto a rm

and level base, ensuring the

base has suitable drainage

and is free from areas where

standing water can collect.

Secure the two oor sections

together using 14x40mm

screws.

*Make sure to stagger the

screws to avoid colliding.

14x40mm Screws

Step 3

Place the rst assembled plain gable

and plain side onto the oor and

x in place.

Fix the corners with 50mm

screws.

Do not secure the building

to the oor until the roof is

xed.

3x50mm Screws

Step 4

Following the same method outlined

in step 3, attach the next plain side &

the door panel to the assembly.

Fix the corners with 50mm

screws.

Do not secure the building

to the oor until the roof is

xed.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 5

Following the same method outlined

in step 3, attach the remaining plain

gable and window panel to the

assembly.

Fix the corners with 50mm

screws.

Do not secure the building

to the oor until the roof is

xed.

9x50mm Screws

bbb

70mm

screw

100mm

screw

Pre drill

hole

30mm

screw

Pre drill

hole

30mm

screw

Pre drill

hole

50mm

screw

Pre drill

hole

P 4

Please retain product label and instructions for future reference

Step 7

Locate the truss centrally in

the building. Align the top of

the truss with the top of the

gables.

*Use a piece from the xing

kit as a guide.

Pencil mark the position and

remove the truss.

Place the truss blocks up to

the pencil mark and x

using 2x70mm screws per

block.

Rest the truss on top of the

blocks and secure into place

using 1x100mm screw per

side as shown in the

illustration.

4x70mm Screws

2x100mm Screws

Step 6

Place the master and slave door into

the door panel and x into place with

3x T-hinges per door and 7x30mm

screws per hinge.

*Ensure to screw through the boards

into the framing on the back of each

door.

42x30mm Screws

Step 8

Place the roof panels on top of

the building ensuring they sit

into the cut outs on the gables

and truss.

*Make sure there is an equal

amount of overhang on either

side of the building.

Secure into position using

13x30mm screws per roof section,

screwing through the boards into

the gable and truss framing.

26x30mm Screws

Step 9

Once the roof is xed secure

the building to the oor with

36x50mm screws.

36x50mm Screws

Felt

tacks

HANDLE

WITH CARE

40mm

screw

Pre drill

hole

Pre drill

hole

Pre drill

hole

*Cut down trims to t

P 5

Please retain product label and instructions for future reference

Step 10

Cut the felt into four strips lay onto

the roof as shown in the illustration.

*Ensure there is approximately 50mm

of overhanging felt each side.

Once the felt is laid out x to the

roof using felt tacks at 100mm

intervals.

*Felt size: 3210mm

170x Felt Tacks

Step 11

Fit the cover trims to the building

and secure in place with 26x40mm

screws as shown in the illustration.

26x40mm Screws

Step 12

Place the cover strip 13mm above

the gap in the window panel and

x into place using 3x30mm screws.

*Measure and trim the strip before

tting.

3x30mm Screws

If you would like the widows

to open attach the window to

the strip using 2x butt hinges.

Fix the hinges to the window

using 3x16mm screws per

hinge and to the strip with

3x30mm screws.

6x16mm Screws

6x30mm Screws

If you would like the window

to be xed, secure the window

into the gap using 4x30mm

screws. Ensure to screw through

the window into the panel

framing.

4x30mm Screws

13 13

Opening Window

Fixed Window

30mm

screw

30mm

screw

16mm

screw

30mm

screw

Pre drill

hole

30mm

screw

Pre drill

hole

Step 14

Fix the casement say to the

window then align the xings

to the window panel.

*Ensure the casement stay ts

onto the xings before securing

in place.

6x16mm Screws

mm screw

Pre drill

hole

Step 15

Attach the door strips to the door

panel framing either side of the

door using 3x30mm screws per

strip.

Align the tower bolts with the top

and bottom of the slave door and

x into place using 8x30mm black

screws per tower bolt.

*With the bottom tower bolt mark the

bolt position and drill into the door

panel framing to allow the bolt to latch.

6x30mm Screws

16x30mm Black Screws

30mm

screw

P 6

Please retain product label and instructions for future reference

Pre drill

hole

30mm

screw

Flat head

Grub Screw

2x30mm screw

Screws provided with lock

Do not over tighten the screws

Step 13

Rim lock xing

Fig 1. (internal view)

Place the lock onto internal horizontal

framing ensure alignment with the

pre drilled holes before xing. Align

Lock keep with lock and x with

screws provided.

Do not over tighten the screws,

otherwise the locking mechanism will

not work.

Fig 2.

Place door handle bar through the

lock as in diagram, x door handle

onto bar with the at headed grub

screw.

g 3. (External view)

Fir the door handle cover over the bar

and x with 2x30mm screws

provided. Fix the door handle onto

bar with the at headed grub screw

as in diagram.

2x30mm Screws

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Please retain product label and instructions for future reference

Step 16

Fit the cover trims and nials to

the gable sides securing with

12x40mm screws as shown in

the illustration.

*Before xing into place measure

and cut down the cover trims to

size.

12x40mm Screws

*Cut down trims to t

40mm

screw

Pre drill

hole

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01OSBA0406DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTGRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0705SDNW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01SHPWOR1210DDOW-V2 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPOT0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03PTODB0406-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES1008-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTSHOA08066WBF-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVAX0604SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0628AXNE0503HGDD2MW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0619RANE3503FGSD3TW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01GRO1008DD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTOVRA0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products Wessex 03WES0808-V3 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0634RANE0504FGDD2TW1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04DTSTRDAX0406HGS-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 04DTSTRDPN0804HGS-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 0644AXNE0503HGDD2MW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02HIDE0705-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 05DTOVPN0305DD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OSBP1006SDFW-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0806SDSEC-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 03DTSHCR0808FGD2TW-V2 Bedienungsanleitung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung