Mercia Garden Products 03LBRO1008-V7 Bedienungsanleitung

P 1

03-LBRO1008-V7

10X8 COMBI SUMMERHOUSE V7

2mm Drill bit

x2 Winter = High Moisture = Expansion

Summer = Low Moisture = Contraction

All building’s should be

erected by two adults

For ease of assembly, you

MUST pilot drill all screw

holes and ensure all screw

heads are countersunk.

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

CAUTION

Every eort has been made during the

manufacturing process to eliminate the

prospect of splinters on rough surfaces of the

timber. You are strongly advised to wear gloves

when working with or handling rough sawn

timber.

**Protim Aquatan T5 (621)**

Your building has been treated with Aquatan.

Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct

application of Aquatan solution and then allowed to dry.

Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and

garden buildings.

Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl

sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.

Please retain product label and instructions for future reference

General Instructions

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied)

including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm

bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions.

For the duration of heavy or extended periods of rain, swelling of the wood panels may

occur. Warping of the wood may also occur during excessive dry spells due to an interior

moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is

suggested that the outdoor building is sprayed with water during extended periods of

warm sunshine and sheltered as much as possible during rain or snow.

Our buildings are pre treated with a water based treatment**; this only helps to protect

the product during transit and for upto 3 months against mould. To validate your

guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated

with a wood preserver within the rst three months of assembly and thereafter in

accordance with the manufactures recommendations. Care must be taken to ensure

the product is placed on a suitable base.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:

Ensure that there will be access to all sides for maintenance work and annual

treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to

diagrams for the base dimensions, The base should be slightly smaller than the external

measurement of the building, i.e. The cladding should overlap the base, creating a run

o for water. It is also recommended that the oor be at least 25mm above the

surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in

the case of childrens products independently tested to EN71 level, we cannot accept

responsibility for your safety whilst erecting or using this product.

Refer to the instructions pages for you specic product code

11 12 13 14 15

16 17 18

2345

6789

22 30

P 2

03LBRO1008-V7

Overall Dimensions:

Width = 3114mm

Depth = 2512mm

Height = 2146mm

Base Dimensions:

Width = 3016mm

Depth = 2413mm

Please retain product label and instructions for future reference

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

Door Panel Back Panel Short Panel Short Window

Panel

AI-03LBRO1008-V7DP

Internal Panel

Floor Roof Storage Back

Panel

Storage Door

Panel

Side Panel

Storage Door

Slave Door

Master Door

AI-03LBRO1008-V7MD

Under Roof

Storage Gable Left Veranda Small Floor

Double Boarded Gable Top

Gable Top Right

Gable Top Left

Storage Gable Right

5xFloor Blocks - 28x28x400mm

Cover Trim A - 12x56x1980mm

2x Cover Trim B - 12x56x2000mm

Cover Trim C - 12x56x2011mm

Cover Trim D - 12x56x2040mm

Cover Trim E - 12x56x2070mm

2x Cover Trim F - 12x56x2080mm

4x Front Fascia - 12x134x1250mm

2x Side Fascia - 12x134x1557mm

F2828-400mm

S12134-1557mm

Fixing Kit

Door Stop

32 33

Felt

34 35

36 37

Press Lock

Chrome Handle

4x Barrel Bolt

2x Door Handles

Fixing Kit continues on P3

AI-03LBRO1008-V7BP AI-03LBRO1008-V7SP

AI-03LBRO1008-V7SWP

AI-03LBRO1008-V7INP

AI-03LBRO1008-V7F AI-03LBRO1008-V7R

AI-03LBRO1008-V7SBP AI-03LBRO1008-V7STD

AI-03LBRO1008-V7SP

AI-03LBRO1008-V7SGL AI-03LBRO1008-V7SGR AI-03LBRO1008-V7UR AI-03LBRO1008-V7V AI-03LBRO1008-V7SF

AI-03LBRO1008-V7GTDB

AI-03LBRO1008-V7GTR

AI-03LBRO1008-V7GTL

S12134-1250mm

S1256-1980mm

S1256-2000mm

S1256-2011mm

S1256-2040mm

S1256-2070mm

S1256-2080mm

QTY x2 QTY x2

QTY x2

AI-03LBRO1008-V7SD AI-03LBRO1008-V7STD

PLY TRIANGLE

PI-07-0162

PI-07-0067

PI-07-0162

PI-07-0001

2x Door Trim - 16x60x1698mm

F1660-1698mm (rounded edge)

2x Press Lock Base-

28x28x95mm

F2828-95mm

16 18

PI-02-0352

P 3

Please retain product label and instructions for future reference

16 17 17

12x Butt Hinge

Key Plate

4x Turn Button

Nail BagFixing kit cont..

Step 1

Place the 2 oor panels (No. 6) onto a rm

and level base , ensuring the

base has suitable drainage & is free from

areas where standing water can collect.

Secure the oors together using the

Floor Blocks (No.22) and 10x30mm

screws per oor.

Once tted, turn the oor assembly the

right way up.

20x30mm Screws

Pre Assembly

Before assembling remove the transportation

blocks from the bottom of each panel.

Pre drill

hole

30mm

screw

Step 2

Flip the assembled Floor (No. 6) over and Place

the small oor (No. 15) ush against

the assembled oor.

Using 4x50mm screws x the small oor in

place as shown in the diagram.

6x50mm Screws

Pre drill

hole

50mm

screw

Step 3a

Assembly of the main door and the

storage door.

Lay each door (No. 16, 2x No. 17 and

No. 18) at on a level surface, place a

hinge at the top, middle and bottom of

the door and x each hinge (No. 40) into

place using three 30mm screws, ensure

to pre-drill the holes rst. Position the

hinges as shown in the diagram (only

two doors have been shown in the

illustration) to ensure that they are in the

correct place before attaching the doors

to the door panel.

Place the door panels (No. 1 and No. 9)

at on the ground and the doors within

the aperture. Position the doors equally

within the space and then using 30mm

screws secure the doors in place.

72x30mm Screws

17 17 18

PI-07-0066

PI-07-0017

PI-07-0034

Pre drill

hole

30mm

screw

Mortice Lock

PI-07-0017

50mm Screw x 119

Felt Tacks x 165

30mm Screw x 162

10mm Screw x 8

30mm Black Screw x 4

70mm Screw x 10

P 4

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,

Sutton On Trent,

Newark,

Nottinghamshire,

NG23 6QN

www.merciagardenproducts.co.uk

Please retain product label and instructions for future reference

Step 3b

Fit the mortice lock (No. 42) into

the recess and x in place with the screws

provided. Fit the key plate(No. 39) to the

opposite door using the 4X30mm screws

provided.

Fix door handles (No. 38) using 8x30mm

screws.

Fix the Door Cover Strips (No. 31) in

positionas shown then t barrel bolts

(No. 37) to top and bottom of the door

strips as shown in diagram. Use 4x10mm

screws per barrel bolt.

Ensure doors open and close freely.

10x30mm Screws

8x10mm Screws 39

41 The Mortice Lock is Reversible

Step 4

Fix the side of the short panel (No. 3)

against the back of the back panel (No. 2)

with 3x50mm screws as shown in diagram.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

Step 5

Fix the side of the short panel (No. 3)

against the side of the short window panel

(No. 4) with 3x50mm screws as shown in

diagram.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

Step 6

Fix the side of the Internal Panel (No. 5)

against the back of the Back Panel (No. 2)

with 3x50mm screws as shown in

diagram.

Do not secure the building to the Floor

until the roof is tted.

3x50mm Screws

Pre drill

hole

30mm

screw

10mm

screw

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

P 5

Please retain product label and instructions for future reference

Pre drill

hole

70mm

screw

Step 7

Place the door panel (No. 1) onto the

assemblybetween the Window Panel

(No. 4) and Internal Panel (No. 5). Fix with

6x70mm screws as shown in diagram

internally.

Do not secure the building to the Floor

until the roof is tted.

6x70mm Screws

Step 8

Place the Gable Top Left/Right (No. 21/No. 20)

upon the top of the side panel, slotting

the groove of the boarding on the gable

into the tongue of the side panel as shown.

Fix with 4x50mm screws per gable top as

shown in diagram.

8x50mm Screws

Step 9

Fix the side of the Storage Back Panel (No. 8)

against the side of the Back Panel (No. 2)

with 3x50mm screws as shown in

diagram.

Fix with 3x50mm screws per gable top as

shown in diagram.

**Be careful to ensure positions of

screws do not interfere with previously

placed screws**

3x50mm Screws

Step 10

Fix the side of the Side Panel (No. 10)

against the back of the Storage Back

Panel (No. 8) with 3x 50mm screws as

shown in diagram.

Fix with 3x50mm screws per gable

top as shown in diagram.

Do not secure the building to the

Floor until the roof is tted.

3x50mm Screws

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

P 6

Please retain product label and instructions for future reference

Step 11

Place the Double Boarded Gable Top (No. 19)

on top of the Side Panel (No. 10) slotting

the groove of the boarding on the gable

into the tongue of the side panel as shown.

Fix with 4x50mm screws per gable top as

shown in diagram.

4x50mm Screws

11 12

Step 13

Place the Assembled Storage Door panel

(No. 9) against the end of the Sorage

Gable Sides (No. 11/12) and x into postion

internally.

Fix with 3x50mm screws per side as

shown in diagram.

Do not secure the building to the Floor

until the roof is tted.

6x50mm Screws

Step 12

Place the Storage Gable Sides Left/Right

(No. 11/12) against the sides of the Internal

(No. 5) and Side Panel (No. 10) with the

boarding facing outwards as shown.

Fix with 3x50mm screws per gable as

shown in diagram.

Do not secure the building to the Floor

until the roof is tted.

6x50mm Screws

Step 14

Place the Veranda (No. 14) ush to the

building as shown to make sure the building

is square.

Fix with 4x70mm screws per gable top as

shown in diagram. Make sure to not screw

into the doors.

4x70mm Screws

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

Pre drill

hole

70mm

screw

Please retain product label and instructions for future reference

Step 15b

Fix the two Roof panels together using

50mm oset from eachother as shown

in the diagram.

Do not secure the building to the Floor

until the roof is tted.

8x50mm Screws

Step 15c

Screw through panel into the alligned

Roof bearers as shown in the diagram.

Do not secure the building to the

Floor until the roof is tted.

*External panels not shown

8x50mm Screws

Step 15a

Place the Roof Panels (No. 7) onto the top

of the building. Allign the 2 Roof Panels

so they sit square before xing into postion.

Do not secure the building to the Floor

until the roof is tted.

Step 16a

Once the Roof is alligned and secure the

Floor can be xed into postion.

Fix the building into place by screwing

through the panel into the oor making

sure to screw into the oor bearers.

*External panels not shown

64x50mm Screws

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

Pre drill

hole

50mm

screw

P 7

HANDLE

WITH CARE

Please retain product label and instructions for future reference

Step 16b

Continue to x the building into place by

screwing through the panel into the oor

making sure to screw into the oor bearers.

*External panels not shown

Step 18

Cut the Felt (No. 34 ) into 3 sheets and lay

onto the roof.

*Ensure there is approximately 50mm of

overhang around the building.

Fix into place using 165x felt tacks at

100mm intervals.

165x Felt tacks Felt Length 3224mm

Step 17

Place the Under Roof(No. 13) into position,

making sure it is ush to the Door panel

and Storage section.

Fix in place making sure to screw through

the Roof framing. Pre-drill holes rst.

15x30mm Screws

Step 19

Fix the Facias (4x No. 29 and 2x No. 30)

into position as shown.

No. 30 are for the front and No. 29 are

for the side.

Fix in place using 18x30mm screws.

18x30mm Screws

Pre drill

hole

50mm

screw

Pre drill

hole

30mm

screw

Felt

tacks

Pre drill

hole

30mm

screw

P 8

Please retain product label and instructions for future reference

Step 20

Fix the Cover Trims (No. 23, 2x No. 24,

No. 25, No.26, No.27 and 2x No. 28) into

position as shown.

Fix each strip into position using 3x30mm

screws per trim.

24x30mm Screws

28 26

24 25

Step 22

Pre drill holes and then x Chrome Handle

(No. 36) using 45mm bolt as shown in diagram.

Fix Door Stop (No. 32) to bottom right of door

panel at the back. Use 3x30mm screws.

2x45mm Bolt

3x30mm Screws

Pre drill

hole

30mm

screw

Pre drill

hole

30mm

screw

P 9

Step 21

To x the lock to the Shed Door, rst x the Door

Blocks (No. 33) either side of the centre framing

of the Door with 4x40mm screws.

Once the Door Blocks are in place the Lock (No. 35)

can be xed in place as shown with 4x30mm

screws, making sure to align the key hole of the

lock to the key hole of the door.

4x30mm Screws

4x40mm Screws

Pre drill

hole

30mm

screw

40mm

screw

It is ESSENTIAL that you apply wood

treatment immediately after the building

has been assembled.

AFTER TREATMENT:

score around protective

cover on glazing and

carefuly peel

covering back

Please retain product label and instructions for future reference

Step 24

Enjoy your Combi-Summerhouse.

P 10

30mm

screw

Button

Step 23

Attach two Turn Buttons (No. 42) to the Storage

Doorat the top and bottom of the door. Using

black screws ensure the screws go through

into the Storage Door Panel framing.

Attach two further Turn Buttons to the Slave

Door at the top and bottom of the door using

black screws.

These Turn Buttons help to keep your doors

straight during high and low levels of

moisture content in the air.

4x30mm Black Screws

Pre drill

hole

Andere Handbücher für 03LBRO1008-V7

Inhaltsverzeichnis

Andere Mercia Garden Products Gartenhaus Handbücher

Mercia Garden Products

Mercia Garden Products 01TDM0604SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 03WES0808-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02DTTWRS0605-V1-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0510PB-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01DTSHRAX0604SDNW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHPN1208DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0628RANE0403HGDD2SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products ESDXL21PT001 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTSHPWOR1010DDOW-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04DTSTRDAX0406HGS-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01GRO1008DD-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0406SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 0619WKNE2633LBDD1SW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTPRMSHAX1010DDOP-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 05DTMBPN0503DD-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTGRODB1008-V4 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01OVLPA0705SDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01PTOSBA1006DDFW-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 04DTSTRDPN0804HGS-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01PTJER0806-V1 Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 02PLAY511511-V2-PEFC Gebrauchsanweisung

Mercia Garden Products

Mercia Garden Products 01DTSHAX0806SDSEC-V1 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 01MODP0804-V2 Bedienungsanleitung

Mercia Garden Products

Mercia Garden Products 02PLAY511511-V1 Bedienungsanleitung

Beliebte Gartenhaus Handbücher anderer Marken

Lemeks

Lemeks Palmako PA120-5930-6 Installationshandbuch

Rion

Rion Hobby Gardener Bedienungsanleitung

Gartenhaus-King

Gartenhaus-King Valery Bedienungsanleitung

Select

Select ISAAC E9682 Bedienungsanleitung

Palmako

Palmako Saale Bedienungsanleitung

Lemeks

Lemeks Palmako Kira EL16-3623 Installationshandbuch

Palmako

Palmako Roger FR44-5953-2 Bedienungsanleitung

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Bedienungsanleitung

G21

G21 Boston 882 Bedienungsanleitung

Lemeks

Lemeks Palmako Grace PM56-4529 Installationshandbuch

Shire

Shire Salcey Bedienungsanleitung

Rutland County

Rutland County Burley 6ft Bedienungsanleitung

Palmako

Palmako Roger 27,7 Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5930-9 Installationshandbuch

Lemeks

Lemeks Palmako PM70-6436 Installationshandbuch

Lemeks

Lemeks Palmako PM56-4435 Installationshandbuch

Lemeks

Lemeks 106214 Installationshandbuch

POD

POD Camping 480 Bedienungsanleitung