Warning! Read and understand
instructions listed below may result
in electric shock, fi re and/or serious
Keep your work area clean and well
Cluttered benches and dark areas
Do not operate power tools in
explosive atmospheres, such as in
the presence of fl ammable liquids,
sparks which may ignite the dust
Keep bystanders, children, and
visitors away while operating a
Double Insulated tools are equipped
with a polarized plug (one blade is
fi t in a polarized outlet only one way. If
the plug does not fi t fully in the outlet,
reverse the plug. If it still does not fi t,
contact a qualifi ed electrician to install
a polarized outlet. Do not change the
eliminates the need for the three
wire grounded power cord and
grounded power supply system.
Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges, and refrigerators.
an increased risk of electric shock if
Do not expose power tools to rain
a power tool will increase the risk of
Do not abuse the cord. Never use
the cord to carry the tools or pull
the plug from an outlet. Keep cord
away from heat, oil, sharp edges
or moving parts. Replace damaged
increase the risk of electric shock.
When operating a power tool
outside, use an outdoor extension
cord marked “W-A” or “W”.
cords are rated for outdoor use and
reduce the risk of electric shock.
Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use tool while tired or under
the infl uence of drugs, alcohol, or
while operating power tools may result
in serious personal injury.
Dress properly. Do not wear loose
clothing or jewelry. Contain long
hair. Keep your hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long hair
can be caught in moving parts.
Avoid accidental starting. Be sure
switch is off before plugging in.
Carrying tools with your fi nger on the
switch or plugging in tools that have
the switch on invites accidents.
Remove adjusting keys or wrenches
before turning the tool on.
or a key that is left attached to a
rotating part of the tool may result in
Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance enables
better control of the tool in unexpected
Use safety equipment by always
wearing safety goggles or full-face
non-skid safety shoes, hard hat, or
hearing protection must be used for
appropriate conditions. Using personal
safety devices and working in safe
environment reduces risk of injury. Use
the tool only in ventilated area.
Use clamps, vise or other practical
ways to secure and support the
workpiece or hoof to a stable
Holding the object by hand
or against your body is unstable and
unsafe and may lead to loss of control.
Disconnect the plug from the
power source before making any
adjustments, changing accessories,
safety measures reduce the risk of
starting the tool accidentally.
Store idle tools out of reach of
children and other untrained
the hands of untrained users.
Maintain tools with care. Keep
cutting tools sharp and clean.
Properly maintained tools, with sharp
cutting edges, are less likely to bind
and are easier to control.
Check for misalignment or binding
of moving parts, breakage of
parts, and any other condition that
may affect the tools operation. If
damaged, have the tool serviced
caused by poorly maintained tools.
Use only accessories that are
recommended by the manufacturer
be suitable for one tool may become
hazardous when used on another tool.
Tool service must be performed
only by qualifi ed repair personnel.
Service or maintenance performed
by unqualifi ed personnel could result
in a risk of injury and could void the
When servicing a tool, use only
identical replacement parts. Follow
instructions in the Maintenance
unauthorized parts or failure to follow
Maintenance Instructions may create a
risk of electric shock or injury. Certain
cleaning agents such as gasoline,
carbon tetrachloride, ammonia, etc.
may damage plastic parts.
Be aware of the switch location,
when placing the tool down or
when picking the tool up.
accidentally activate the switch.
After changing any accessory or
making any adjustments, make
sure the Allen key or any screws
Hold the grinder by insulated
gripping surfaces when performing
an operation where the cutting tool
may contact hidden wiring or its
Contact with a “live” wire
will make exposed metal parts of the
tool “live” and shock the operator. If
cutting into existing walls or other blind
areas where electrical wiring may exist
is unavoidable, disconnect all fuses or
circuit breakers feeding this worksite.
