Merrylock MK1100 Bedienungsanleitung
Instruction Book
Instruction Book
Instruction Book
1-Needle 3-Thread
Overlock Sewing Machine
“IMPORTANT SAFETY INSTRUCTIONS“
“DANGER“___
“WARNING“ “ATTENTION“___
When using an electrical appliance, basic safety precautions should always be followed, including the following:
Read the instruction carefully before you use the machine.
1. The appliance should never be left unattended when plugged in.
2. Always unplug this appliance from the electric outlet immediately after using and before cleaning.
3. Always unplug before re-lamping. Change the light bulb only with the same of bulb and type rated max. 220~
240V/15W or 115V/15W.
* Do not allow this appliance to be used as a toy. Close attention is necessary when this appliance is used by
near children and infirm persons.
* Use this appliance only for its intended use as described in this manual. Use only attachments recommended
by the manufacturer as contained in this manual.
* Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been
or damaged, or dropped into water. Return the appliance to the nearest authorized dealer or service center for
examination, repair, electrical or mechanical adjustment.
* Never operate the appliance with any air openings blocked. Keep ventilation openings of the sewing machine
and foot control free from the accumulation of lint, dust, and loose cloth.
* Keep fingers away from all moving parts. Special care is required around the sewing machine needle and
cutter.
* Always use the proper stitch plate. The wrong plate can cause the needle to break.
* Do not use bent needles.
* Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
* Switch the sewing machine off “ O “ when marking any adjustments in the needle area, such as threading
needle area, such as threading needle, changing needle, threading looper, or changing presser foot and the
like.
* Always unplug the machine from the electrical outlet when removing covers, when covers are opened to raise
the upper cutter or thread the loopers, when lubricating or when making any other user servicing
mentioned in the instruction manual.
* Never drop or insert any abject into any opening.
* Do not use outdoors.
* Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
* To disconnect, turn all controls to the off “ O “ position, then remove plug from outlet.
* Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
* Basically, the machine should be disconnected from the electricity supply when not in use.
* If the power cord of this appliance is damaged, it must be replaced with a special cord by your nearest
authorized dealer or service center.
* This appliance is provided with double insulation. (except USA/ CAN) Use only identical replacement parts. See
instructions for servicing double insulated appliances.
* If oil gets in eyes, immediately, rinse the oil out with water. If you swallow oil by mistake, immediately consult a
medical doctor.
* Close cover before operating machine.
or
dropped
adjustments
To reduce the risk of electric shock:
Pour reduire le risque de décharges électriques :
To reduce the risk of burns, fire, electric shock, or injury to persons:
Pour réduire le risque de brûlures, de feu, de décharges électriques ou de blessures Aux personnes :
TABLE OF CONTENTS
1
TABLE OF CONTENTS
Parts Name............................................................................................................................................................ 2
Standard Accessories..........................................................................................................................................
Specifications........................................................................................................................................................
Opening and Closing the Looper Cover.............................................................................................................
Opening and Closing the Sewing Table..............................................................................................................
Opening and Closing the Accessory Box...........................................................................................................
Connecting the Machine to the Power Supply...................................................................................................
How to Use Foot Controller and Control the Sewing Speed.............................................................................
How to Turn the Balance Wheel...........................................................................................................................
How to Attach the Chip Box.................................................................................................................................
Stretch Up the Thread Guide Bar.........................................................................................................................
Attaching the Thread Stripping Disc and net......................................................................................................
Raising or Lowering the Presser Foot.................................................................................................................
How to Change (Remove) the Presser Foot........................................................................................................
How to Thread the Machine............................................................................................................................
-Threading the upper looper.................................................................................................................................
-Threading the lower looper..................................................................................................................................
-Threading the needle.........................................................................................................................................
Securing Ends......................................................................................................................................................
Adjustment of Differential Feed (DF type only)................................................................................................
Thread tension adjusment..................................................................................................................................
Adjustment of Stitch length................................................................................................................................
Adjustment of Cutting Width..............................................................................................................................
Replacing the Light Bulb....................................................................................................................................
Changing the Needle...........................................................................................................................................
Changing the Upper Knife...................................................................................................................................
Using the Needle Plate........................................................................................................................................
Rolled Hemming, Picot Edging and Narrow Hemming....................................................................................
Cleaning and Oiling.............................................................................................................................................
Trouble Shooting.................................................................................................................................................
Optional Feet.......................................................................................................................................................
3
3
4
4
4
5
5
5
5
6
6
7
7
8-10
8
9
10
11
12
13
14
14
14
15
15
16
17
18
19
20
2
Parts Name
Pre-tension thread guide
Thread guide bar
Thread guide
Spool pin
Spool holder
Spool stand
Stitch length dial
Side Cover
Balance wheel
Power socket
Light and Power switch
Needle thread tension dial
Foot pressure cover
Thread take-up lever cover
Needle thread guide
Needle thread guide
Sewing table
Looper cover
Base plate
Upper looper thread tension dial
Lower looper thread tension dial
Needle clamp
Presser foot
Sewing table
Feet holder
Accessory box
Differential feed dial
Extension table
Presser foot lifter
Motor cover
Lamp cover
3
Standard Accessories
Screw driver Set of Needles Tweezers Nets
Lint brush Oil Upper knife Thread stripping discs
Specifications
Hexagon wrench Chip box
Max. speed
Stitch length
Stitch width
Presser foot height
Differential feed (DF type only)
Needle
Dimentions
Net weight
Up to 1300 r.p.m.
1-4mm
3-5mm
Max. 6mm
0.8-2.0
ELx705 # 12 or # 14
292Wx295Dx290H mm
7.4 KGS
4
To open:
Hold the hollow to the right as far as it will go, then pull
looper cover toward you.
To close:
Lift looper cover and push against the machine. The
looper cover snaps into the position automatically.
Opening and Closing the Looper Cover
Looper cover
Hollow
Metal lever
Accessory box
To open:
Lift the metal lever, then hold the sewing table going
down.
To close:
Lift sewing table and push it back to the position.
Opening and Closing the Sewing Table
To open:
Draw out the box, it can store all standard accessories.
To close:
Push it back to the position.
*For optional accessories, it can only be stored in the
attached accessories bag.
Opening and Closing the Accessory Box
5
Base plate
Chip box
Insert the projection under the base plate.
How to Attach the Chip Box
Always turn the balance wheel toward you.
Balance wheel
How to Turn the Balance Wheel
ON
I
O
OFF
Light and power switch
Foot controller
1. Tread your foot on the controller.
2. Press and release the controller to practice the
sewing speed.
3. The harder you press on the controller,the faster
the machine runs.
How to Use the Foot Controller and
Control the Sewing Speed
1. Turn off the light and power switch.
2. Connect two plugs to power socket and electrical outlet.
3. Turn on the light and power switch.
-Caution-
Always disconnect the plug from electrical outlet:
- when machine is not in use.
- when attaching or removing parts.
- when threading or cleaning the machine.
Connecting the Machine to the Power Supply
Electrical outlet
Foot controller
Power socket
Light and Power
switch
6
1. Pull the thread guide bar up to the top.
2. Turn the thread guide bar to make it comes right above
the spool pins and locked into the stopper.
1. When you use a small thread spool, pull out the spool holder from the spool pin. Then place the spool
with its slit side up, and put the thread stripping disc on top.
2. If the thread would slip down from the spool during threading and/or sewing, put a net on the spool as
illustrated for preventing jamming. The nets are supplied with the machine.
12
Stretch up the Thread Guide Bar
Attaching the Thread Stripping Disc and Net
Spool pin
Spool holder Thread stripping disc
7
1. Raise the presser foot lifter.
2. Turn the balance wheel to raise the needle.
3. Press the lever to drop off the presser foot.
4. Raise the Presser foot lifter again to remove the
presser foot.
5. Raise the presser foot lifter, and apply the desired
presser foot under the foot holder and make the pin
on the foot lies under the groove of the foot holder.
6. Lower the foot holder and push the lever to lock the
foot in place.
7. Raise the presser foot lifter and see the presser foot
is in place.
Presser
foot lifter
How to Change (Remove) the Presser
Foot
1. Apply the presser foot lifter to raise or lower the
presser foot.
2. Always keep the presser foot down when sewing.
Raising or Lowering the Presser Foot
Presser foot
Foot holder
Lever
Needle
Lever Groove
Pin
8
-NOTED-
1. Always thread the upper looper first, then lower
looper, needle on the right and needle on the left.
A threading chart is placed on the machine body
inside the looper cover.
2. Incorrect threading will cause of skipped stitch,
broken thread or uneven thread tension. Before
to sew, make sure that your machine is threaded
properly.
- Open the looper cover.
- Place the spool on the spool holder second from the right.
- Draw the thread through the pre-tension thread guide (1)
from right to left.
- Thread from left to right around the Thread guide (2)
- Thread guides (3, 4, 5)
- Turn the balance wheel toward you until the upper looper
comes outside of the needle plate, and apply the tweezers
to pass thread through looper eye (6)
Threading the upper looper (green)
How to Thread the Machine
()5
(3)
()4
(6)
()2
(1)
Upper looper
3
4
2
312
(a) (b) ( )
c
1
3
4
2
3
4
2
3
4
2
3
4
2
3
4
2
3
4
2
Inhaltsverzeichnis
Andere Merrylock Nähmaschine Handbücher
