Metra Electronics DAT Combo Bedienungsanleitung

Door Access Terminal Combo User Manual

Page 2

Door Access Terminal Combo User Manual

Table of contents

Door Access Terminal Combo User Manual............................................................................................ 3

Product description............................................................................................................................. 3

Basic Parts ........................................................................................................................................... 4

User Interface...................................................................................................................................... 4

Operating indicator............................................................................................................................. 5

User card presentation ....................................................................................................................... 6

Passage Allowed ............................................................................................................................. 6

Passage denied ............................................................................................................................... 7

PIN code requested ..........................................................................Error! Bookmark not defined.

Signal not activated ........................................................................................................................ 7

Master card presentation ................................................................................................................. 10

Latch/Unlatch function ..................................................................................................................... 10

User card with permanent option presented...................................Error! Bookmark not defined.

Master card presented ................................................................................................................. 10

Alarm signalization............................................................................................................................ 11

Page 3

Door Access Terminal Combo User Manual

Manufacturer:

Metra inženiring d.o.o.

IOC Trzin

Špruha 19

SI-1236 Trzin, Slovenia

phone:

fax:

web:

+386 1 56 10 740

+386 1 56 10 744

www.metra.si

System:

Metra Access Control System

Product Group:

Door Access Terminal Combo

Types:

DLCIS (ISO14443A/B, ISO 15693)

DLCLF (LF Multitag)

DLCMF (Mifare, ISO14443A/B)

Year of Construction:

2011 - 2012

Declaration of Conformity:

Metra Access Control products have been developed, designed and

manufactured in accordance with the EU directive for Electromagnetic

Compatibility (2004/108/EC).

Door Access Terminal Combo User Manual [rev.0-050912]

2012 Metra inženiring d.o.o.

No part of this manual may be reproduced in any form or by any means without prior written permission of Metra inženiring d.o.o.

The contents of this manual are subject to change without notice.

All efforts have been made to ensure the accuracy of the contents of this manual, however, should any errors be detected, Metra inženiring would greatly appreciate being informed of

them. Metra inženiring d.o.o. can assume no responsibility for any errors in this manual.

Product description

Door Access Terminal Combo (DAT Combo) is designed to

form a one-way check point in Metra Access Control

Systems and Electronic Locking Systems.

In Access Control Systems a RFID media is used as a door

key. For higher security (e.g. outside door, etc.) a user

specific PIN code as an addition to RFID media can be used.

In Electronic locking systems a RFID media or a locker

number followed by a locker’s PIN code can be used as a

door key.

When access is granted device gives a single relay signal for

access mechanisms such as electric door strike, automatic

door, etc. Normally it is mounted near door where passage

control is needed.

Door Access Terminal operates on line with Metra software.

It must be connected to Metra NET Network.

Passage on Door Access Terminal Combo for particular RFID

ticket can also be externally controlled by 3rd party SW via

TCP/IP software interface.

Operating parameters are defined in the Metra software.

Event data from device is used for further analyses with this

software.

Page 4

Door Access Terminal Combo User Manual

Basic Parts

description

PIN CODE signal

12 key illuminated keypad

NO signal

OPERATE (Power) signal

OK signal

Antenna field

Standard models are supplied with front mask in glossy black colour. For additional colours contact

Metra sales.

User Interface

Door Access Terminal user interface uses optical signals ( , , , and ) and an acoustic

beeper signal to inform the user about operation progress. Signals are explained in the following

tables.

NOTE: Keypad’s illumination may be ON or OFF, depending on the type of the system. In some

systems it is OFF by default and lights up when a PIN code is requested and in other systems it is

always ON.

Page 5

Door Access Terminal Combo User Manual

OK signal (green)

state

Description

passage is enabled (lock is unlocked); accompanied with short beep acoustic signal

NO signal (red)

state

Description

flashing

RFID media is recognized but passage is denied; accompanied with interrupted acoustic

signal

PIN CODE signal (blue)

state

Description

flashing

PIN code is requested; accompanied with interrupted acoustic signal

OPERATE signal (blue)

state

Description

flashing

device operates normally

Operating indicator

When the unit is running a blue OPERATE signal light is flashing. Keypad illumination is ON or OFF,

depending on the type of the system.

Metra Electronic locking systems

Metra Access Control systems with

PIN only functionality

Metra Access Control systems

Page 6

Door Access Terminal Combo User Manual

RFID media as a user door key

Approach the card to the antenna field. Reading distance is

3 –5 centimetres from the device surface. Hold the card in

field for a few moments for Door Access Terminal to read

and process the card.

Short Acoustic signal is activated when the cards is

recognized.

RFID media accepted and passage allowed

When card is accepted, “OK” optical signal lights up and

short acoustic signal is activated.

The door is unlocked.

Remove the card form the antenna filed.

RFID media accepted and PIN code requested

When card is accepted, “PIN CODE” optical signal starts

flashing accompanied with short acoustic signals.

Enter your 4 digit PIN code. By entering the last digit you

automatically confirm the PIN code.

NOTE 

Only 4 digit PIN codes are supported by Metra software

user interface.

Page 7

Door Access Terminal Combo User Manual

If the PIN code is correct, “OK” optical signal lights up and

short acoustic signal is activated.

The door is unlocked.

If the PIN code is rejected, “NO” optical signal starts flashing

and interrupted acoustic signal is activated for 2 seconds.

Door remains locked.

Passage denied

If the card is rejected (passage not allowed) “NO” optical

signal is flashing and interrupted acoustic signal is

activated for 2 seconds.

Door remains locked.

Remove the card form the antenna filed.

Signal not activated

If there is no optical signal (door remains locked) the

device is not functioning properly. Call maintenance

personnel.

Page 8

Door Access Terminal Combo User Manual

PIN code as a LCC user door key

NOTE 

This functionality is present only in old Metra LCC systems.

STEP 1: Enter your PIN code and confirm it by pressing the

key.

STEP 2 A: If the PIN code is correct, “OK” optical signal lights

up and short acoustic signal is activated.

The door is unlocked.

STEP 2 B: If the PIN code is rejected, “NO” optical signal

starts flashing and interrupted acoustic signal is activated

for 2 seconds.

Door remains locked.

PIN code as a user door key

This functionality is used in combination with different Metra Electronic Locking Systems for lockers.

PIN code is not used as a standalone key, but always in combination with user’s locker number.

User’s PIN code is also valid as long as he/she has an assigned locker. Once locker expires also user’s

PIN code expires.

Page 9

Door Access Terminal Combo User Manual

STEP 1: Enter your locker’s number and confirm it by

pressing the key.

STEP 2 A: If there is no locker with the number you entered

or there is no reservation for this locker in the database

procedure is rejected, “NO” optical signal starts flashing

and interrupted acoustic signal is activated for 2 seconds.

Door remains locked.

STEP 2 B: If there is a valid reservation in the database for

the locker you entered a “PIN CODE” optical signal starts

flashing accompanied with short acoustic signals.

Enter your 4 digit PIN code. By entering the last digit you

automatically confirm the PIN code.

NOTE 

Only 4 digit PIN codes are supported by Metra software

user interface.

STEP 3 A: If the PIN code is correct, “OK” optical signal

lights up and short acoustic signal is activated.

The door is unlocked.

STEP 3 B: If the PIN code is rejected, “NO” optical signal

starts flashing and interrupted acoustic signal is activated

for 2 seconds.

Door remains locked.

Page 10

Door Access Terminal Combo User Manual

Master card presentation

STEP 1: Approach the MASTER card to the antenna field.

Reading distance is 3 –5 centimetres from the device

surface. Hold the card in field for a few moments for Door

Access Terminal to read and process the card.

STEP 2: When the MASTER card is recognized, “OK” optical

signal lights up and short acoustic signal is activated.

The door is unlocked.

Remove the card form the antenna filed.

Latch/Unlatch function

Latch/Unlatch function is possible from Metra software or by presenting the Master card.

Functionality allows user to permanently open the door lock for prolonged period of time. This

function is especially useful for conference rooms, maintenance purposes and in emergency cases.

Master card presentation

NOTE 

Latch/Unlatch function with Master card is always possible and it cannot be disabled!

STEP 1: Approach the MASTER card to the antenna field.

Reading distance is 3 –5 centimetres from the device

surface. Hold the card in field for a few moments for Door

Access Terminal to read and process the card.

Inhaltsverzeichnis

Andere Metra Electronics IP-Zugriffskontrollsysteme Handbücher

Metra Electronics

Metra Electronics ELDLISS Bedienungsanleitung

Beliebte IP-Zugriffskontrollsysteme Handbücher anderer Marken

ZKTeco

ZKTeco SpeedFace-V5L Bedienungsanleitung

Jantar

Jantar REX A-1-9 Bedienungsanleitung

2N Access Unit Merkblatt

Kedacom

Kedacom KSCA120 Series Bedienungsanleitung

H3C

H3C WX2880X Bedienungsanleitung

G4S

G4S S870-EX Leitfaden

PRASTEL

PRASTEL M2000PE Bedienungsanleitung

Allegion

Allegion interflex IF-281 Cylinder Bedienungsanleitung

TECOM

TECOM TS1067E Bedienungsanleitung

Fermax

Fermax Memokey 100C Benutzerhandbuch

Fermax

Fermax CITYLINE MEMOKEY Bedienungsanleitung

Software House

Software House iSTAR Pro 2U RM Bedienungsanleitung

AKCP

AKCP SP+ Bedienungsanleitung

Bpt

Bpt HNA/102 Bedienungsanleitung

Civintec

Civintec CV9601T-T-1F Bedienungsanleitung

BioMax

BioMax N-X90W Bedienungsanleitung

ZKTeco

ZKTeco OP-200 Bedienungsanleitung

FingerTec

FingerTec s-Kadex Bedienungsanleitung