Metra Electronics 99-5839CH Bedienungsanleitung

INSTALLATION INSTRUCTIONS

99-5839CH

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Touchscreen interface for climate and personalization features

• Painted charcoal with a matte black center

KIT COMPONENTS

• A) Radio/Display trim panel • B) Radio/Display sub-trim panel upper (a) • C) Radio/Display sub-trim panel lower (b) • D) Radio brackets upper (a)

• E) Radio brackets lower (b) • F) Pocket • G) (4) Panel clips • H) (12) #6 x 3/8” Phillips pan-head screws • I) (8) #8 x 3/8” Phillips truss-head screws

• J) Touchscreen display assembly and wiring harness • K) Antenna adapter (not shown)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 9/32” socket wrench

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................3

Kit Assembly

–ISO DIN radio provision with pocket ..................4

–ISO DDIN radio provision .....................................5

Axxess Interface Installation ............................6-13

Final Assembly ..................................................... 10

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Axxess interface built

into touchscreen

Antenna Adapter: Included with kit

Steering wheel control interface: Included with kit

A B C D

H I J

E F G

Ford Mustang 2010-2014

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

1.800.221.0932

MetraOnline.com

DASH DISASSEMBLY

1. Unclip and remove the trim panel

surrounding the shifter, including the

cup holders. (Figure A)

2. Remove (2) 9/32” screws from the

bottom of the radio/climate control

panel, then unclip and remove the

panel. (Figure B)

3. Remove (4) Phillips screws securing the

radio chassis to the vehicle. Slide the

chassis out, then unplug and remove.

(Figure C)

4. Remove (4) Phillips screws securing the

radio display to the vehicle. Slide the

display out, then unplug and remove.

(Figure D)

Continue to Kit Preparation

(Figure C) (Figure D)

(Figure B)(Figure A)

REV. 4/16/2019 INST99-5839CH

KIT PREPARATION

1. There are two different radio/display

sub-trim panels to choose from. One for

mounting the radio in the upper portion

of the kit, and another one for mounting

it in the lower portion. (Figure A)

If mounting the radio in the upper

portion, a factory module will need to

be re-located:

a. Remove the module from the sub-

dash and relocate it to the bottom

of the dash opening. The mounting

brackets attached to the module will

need to be bent outward to make

room for the radio.

(Figure B) (Figure D)

(Figure A) (Figure C)

2. Attach the desired radio/display

sub-trim panel to the radio/display

panel using the (12) #6 x 3/8” pan-head

screws provided. (Figure B)

3. Attach the touchscreen display

assembly to the radio/display sub-

panel using the (4) #8 x 3/8” truss-head

screws provided. (Figure C)

4. Attach the (4) panel clips provided to

the radio/display panel. (Figure D)

Continue to Kit Assembly

1.800.221.0932

MetraOnline.com

KIT ASSEMBLY

(Figure A) (Figure B)

ISO DIN radio provision with pocket

1. Attach the pocket to the appropriate

radio brackets using the (4) #8 x 3/8”

Phillips truss-head screws provided.

(Figure A)

2. Remove the metal DIN sleeve and trim

ring from the aftermarket radio.

3. Slide the radio into the bracket/pocket

assembly, and then secure it using the

screws supplied with the radio.

(Figure B)

Continue to Axxess

Interface Installation

REV. 4/16/2019 INST99-5839CH

ISO DDIN radio provision

1. Attach the appropriate radio brackets to

the radio using the screws supplied with

the radio. (Figure A)

Continue to Axxess

Interface Installation

KIT ASSEMBLY

(Figure A)

1.800.221.0932

MetraOnline.com

AXXESS INTERFACE INSTALLATION

• Crimping tool and connectors, or solder gun, solder, and heat shrink

• Tape • Wire cutter • Zip ties

TOOLS REQUIRED

INTERFACE FEATURES

INTERFACE COMPONENTS

• Axxess interface (built into the touchscreen display)

• 5839 harness

• 16-pin harness with stripped leads

• 4-pin harness with yellow RCA jacks

• Female 3.5mm jack with stripped leads

• Provides accessory power (12-volt 10-amp)

• Retains R.A.P. (retained accessory power)

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains SYNC

• Retains the factory AUX-IN jack

• Provides an aftermarket backup camera input

• Can be used in both ampliﬁed and non-ampliﬁed models

• Retains balance and fade

• Micro-B USB updatable

Connections ...........................................................................................................................................7-8

Installation ...............................................................................................................................................9

Programming ...........................................................................................................................................9

Extra features (SYNC)............................................................................................................................. 10

Touchscreen display operation ..........................................................................................................11-12

Steering wheel control settings .......................................................................................................13-14

Troubleshooting ......................................................................................................................................14

TABLE OF CONTENTS

REV. 4/16/2019 INST99-5839CH 7

CONNECTIONS

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

• If the vehicle is equipped with a Shaker/Shaker-Pro sound system or NAV, connect the Blue/

White wire to the amp turn on wire. This wire must be connected to hear sound from the

factory ampliﬁer.

• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.

•

If the aftermarket radio has a mute wire and the vehicle is equipped with SYNC, connect the

Brown wire to it. If the mute wire is not connected, the radio will turn off when SYNC is activated.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

• Connect the Light Green wire to the parking brake wire

• Tape off and disregard the following (4) wires, they will not be used in this application:

Green, Green/Black, Purple, Purple/Black

From the 5839 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.

• Connect the Yellow wire to the battery wire.

• Connect the Blue wire to the power antenna wire.

• If the vehicle is equipped with NAV, connect the Blue/White wire with a red connector to the

amp turn on wire. This wire must be connected to hear sound from the factory ampliﬁer.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative output.

• For models

with

SYNC: Connect the Red and White RCA jacks labeled “RSE/SYNC/SAT”, to the

audio AUX-IN jacks. Disregard the Red and White RCA jacks labeled “FROM 3.5”, they will not

be used in this application.

• For models

without

SYNC: Connect the Red and White RCA jacks labeled “FROM 3.5”, to the

audio AUX-IN jacks. Disregard the Red and White RCA jacks labeled “RSE/SYNC/SAT”, they

will not be used in this application.

• Disregard the DIN jack, it will not be used in this application.

Continued on the next page

1.800.221.0932

MetraOnline.com

3.5mm jack - steering wheel control retention:

The 3.5mm jack is to be used to retain audio controls on the steering wheel control.

• For the radios listed below: Connect the female 3.5mm connector with stripped leads, to the male

3.5mm SWC jack from the 5839 harness. Any remaining wires tape off and disregard.

•

Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White wire of

the connector. Then connect the remaining steering wheel control wire, normally Brown/White,

to the Brown wire of the connector

•

Metra OE:

Connect the steering wheel control Key 1 wire

(Gray)

to the

Brown

wire.

•

Kenwood or select JVC with a steering wheel control wire:

Connect the

Blue/Yellow

wire to the

Brown

wire.

Note:

If your

Kenwood

radio auto detects as a

JVC

, manually set the radio type to

Kenwood

See the instructions under changing radio type.

•

XITE:

Connect the steering wheel control SWC-2 wire from the radio to the

Brown

wire.

•

Parrot Asteroid Smart or Tablet:

Connect the 3.5mm jack into the AX-SWC-PARROT (sold separately),

and then connect the 4-pin connector from the AX-SWC-PARROT into the radio

Note:

The radio must be updated to rev. 2.1.4 or higher software.

•

Universal “2 or 3 wire” radio:

Connect the steering wheel control wire, referred to as Key-A or

SWC-1, to the

Brown

wire of the connector. Then connect the remaining steering wheel control wire,

referred to as Key-B or SWC-2, to the

Brown/White

wire of the connector. If the radio comes with a

third wire for ground, disregard this wire

Note:

After the interface has been programmed to the vehicle, refer to the manual provided with

the radio for assigning the SWC buttons. Contact the radio manufacturer for more information.

• For all other radios: Connect the 3.5mm jack into the port on the radio designated for an external

steering wheel control interface. Refer to the manual provided with the radio if in doubt as to where the

3.5mm jack goes to.

CONNECTIONS (CONT.)

For models

with

a Shaker system:

• Connect the White RCA jack labeled “SUBWOOFER”, to the subwoofer out jack.

• Disregard the Red RCA jack labeled “CENTER CHANNEL”, it will not be used in this

application.

• Enable Audio Output Attenuation in Conﬁguration Settings after the kit has been

programmed.

For models

with

a Shaker Pro system:

• Connect the Red RCA jack labeled “CENTER CHANNEL”, to the subwoofer out jack.

• Disregard the White RCA jack labeled “SUBWOOFER”, it will not be used in this

application.

• Enable Audio Output Attenuation in Conﬁguration Settings after the kit has been

programmed.

4-pin harness with yellow RCA jacks:

This harness is to be used to add an aftermarket backup camera to the touchscreen

display, if so desired.

• Connect the Yellow RCA jack labeled “Rearview camera”, to the RCA jack on the

aftermarket backup camera.

• Disregard the Yellow RCA jack labeled “AUX video”, it will not be used in this

application.

REV. 4/16/2019 INST99-5839CH 9

It is highly advisable to read the following steps beforehand, to ensure a clear understanding of

what is to be expected. The following steps must be done in the order that they are numbered.

With the vehicle completely off:

1. Connect the

16-pin harness with stripped leads

into port “B” in the touchscreen display.

2. Connect the

5839 harness

to the wiring harnesses in the vehicle. These harnesses are the

ones removed in step 3 of dash disassembly. Then insert the

5839 harness

into port “A”

in the touchscreen display. But do not install this harness until exactly before step 1 from

the

Programming

section. This is a timed process.

If installing a backup camera, and the image is desired to to be displayed onto the touchscreen

display, connect the 4-pin harness with yellow RCA jacks into port “C” in the touchscreen display

4. Disregard ports “D” and “E”, they will not be used in this application.

5. Port “F” is an update port for future ﬁrmware upgrades.

Locate the factory antenna connector in the dash and complete all necessary connections to

the radio. Use the antenna adapter provided to adapt the factory antenna connector to the

aftermarket radio.

I N S TAL L AT I ON PROGRAMMING

1. Refer to step 2 from the Installation section.

2. Start the vehicle.

3. Program the kit:

a. Once the touchscreen display loads up, select the vehicle type.

b. Wait until the radio comes on, and the touchscreen display shows SWC Conﬁgured*.

This process may take up to 3 minutes.

Note: f the touchscreen display does not load up, or the radio doesn’t come on within

3 minutes, and/or the touchscreen display does not show SWC Conﬁgured*, check all

connections, then reset the interface and try again. Refer to the Troubleshooting section.

* For models with steering wheel controls.

Cycle the key off. If the driver’s door is closed, open and close the door. Cycle the key back on.

5. Test all functions of the installation for proper operation, before reassembling the dash.

Note: DO NOT CONNECT!

1.800.221.0932

MetraOnline.com

1. Secure the completed assembly to the dash using the factory screws.

2. Reassemble the dash in reverse order of disassembly using the 99-5839CH radio display trim

panel.

FINAL ASSEMBLY EXTRA FEATURES

SYNC (4.2-inch display screen models only):

If the vehicle is equipped with SYNC, the 99-5839CH can retain this feature.

1. Change the source of the radio to AUX-IN.

2. Press the Info button on the touchscreen display to enter the SYNC menu. Press the climate

control icon to get back to the main menu.

Andere Handbücher für 99-5839CH

Inhaltsverzeichnis

Andere Metra Electronics Rack & Stand Handbücher

Metra Electronics

Metra Electronics MPS-GEN02 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung