Metrix SA6200A Bedienungsanleitung

Doc# 1928171 • REV A (April 2022) Page 1 of 10

Metrix SA6200A (Two-Wire) Accelerometer Replacing 3-Wire Accelerometer on BN 3500 Rack

Installaon Manual

Secon Page

1.0 PURPOSE 2

2.0 REFERENCES 2

3.0 PROCEDURE 2

Doc# 1928171 • REV A (April 2022) Page 2 of 10

1.0PURPOSE

The purpose of this procedure is to congure the BN 3500 rack to be compable with a Metrix SA6200A 2-wire

Accelerometer (Note: The SA6200A is not polarity sensive).

2.0PROCEDURE

Prior to installaon, one needs to have access to the BN soware with password and username. This may require

a purchase in order to make changes to the set-up and conguraon. You will need an USB to RS232 communica-

ons cable. The USB plugs into the operator’s laptop and the 9-way D-type connector into the BN 3500 rack.

2.0REFERENCES

• SA6200A Datasheet-1009516

• SA6200A Manual-M9313

• BN 3500/42M Datasheet-143694

• BN 3500 Rack Conguraon Manual

Doc# 1928171 • REV A (April 2022) Page 3 of 10

From 3500 conguraon soware, click File > Connect > Direct.

5. Verify Rack Address and center Connect Password

Doc# 1928171 • REV A (April 2022) Page 4 of 10

Place arrow over 3500/42M module, right-click on Monitors > 42/42M Proximitor/Seismic Monitor >

3500/42M

Make sure both chanels are set-up as Acve

Doc# 1928171 • REV A (April 2022) Page 5 of 10

Click drop down box for Channel Pair Type and select Acceleraon. Channels come in pairs: 1 &2 and 3 & 4 which

mean if Channel 1 is set-up as acceleraon, then Channel 2 must have acceleraon inputs as well.

Click on opons for Channel 1

Doc# 1928171 • REV A (April 2022) Page 6 of 10

Click on drop down box for Transducer Selecon and Select Nonstandard

Select Scale Factor 100 mV/g.

Doc# 1928171 • REV A (April 2022) Page 7 of 10

Make selecon for Full-scale Range (e.g. select 0-10g’s pk, 0-1 in/s pk, etc.).

Doc# 1928171 • REV A (April 2022) Page 8 of 10

If more than one input, then select Copy. This will duplicate Channel 1 set-up into Channel 2. If not duplicang,

then set up Channel 2 to required conguraon. Note: Both Channel 1 and Channel 2 must be Acceleraon.

From the Opons screens, Slot Input/Output Module Type, use the drop down box and select Prox/Seismic I/O

Module (Internal Terminaon). This procedure asssumes you are connecng the accelerometer directly to the

rack, if not use External Terminaon.

Doc# 1928171 • REV A (April 2022) Page 9 of 10

From the Transducer Selecon box, Type “Nonstandard” select Customize. This will present the Nonstandard

Transducer Jumper Selecon box.

From the Nonstandard Transducer Jumper Selecon box, select Prox/Accel, then click OK

Doc# 1928171 • REV A (April 2022) Page 10 of 10

Make sure jumpers are applied to the Prox/Seismic I/O module for the Prox/Accel jumpers for the associated 42M

you are conguring.

Use only PWR/B and SIG/A for the wired connecon for the 2-wire accelerometer.

Andere Metrix Messgerät Handbücher

Metrix

Metrix GX-1030 Bedienungsanleitung

Metrix

Metrix MX 409 Bedienungsanleitung

Metrix

Metrix PX 110 Bedienungsanleitung

Metrix

Metrix MTX 1032-B Bedienungsanleitung

Metrix

Metrix MX2033 Bedienungsanleitung

Metrix

Metrix 6850-001 Bedienungsanleitung

Metrix

Metrix VM2800 Bedienungsanleitung

Metrix

Metrix ScopiX IV Bedienungsanleitung

Metrix

Metrix MTX I 050-PC Bedienungsanleitung

Metrix

Metrix MX 23 Bedienungsanleitung

Metrix

Metrix IX 3131 Bedienungsanleitung

Metrix

Metrix MX 406B Bedienungsanleitung

Metrix

Metrix IX 3131B Bedienungsanleitung

Metrix

Metrix AG 900 Bedienungsanleitung

Metrix

Metrix MX 350 Bedienungsanleitung

Metrix

Metrix 5500 Bedienungsanleitung

Metrix

Metrix SA6350 Bedienungsanleitung

Metrix

Metrix MX 650 Bedienungsanleitung

Metrix

Metrix MX 350 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung