Metrologic Genesis MS7580 Betriebsanleitung
MS7580 Genesis™
Supplemental Guide for EAS Equipped Models
Copyright
© 2008 by Metrologic Instruments, Inc. All rights reserved. No part of this
work may be reproduced, transmitted, or stored in any form or by any means
without prior written consent, except by reviewer, who may quote brief
passages in a review, or provided for in the Copyright Act of 1976.
Trademarks
Metrologic is a registered trademark of Metrologic Instruments, Inc.
Products identified in this document are hereby acknowledged as
trademarks, registered or otherwise, of Metrologic Instruments, Inc. or their
respective companies.
iii
TABLE OF CONTENTS
Introduction
Document Scope .............................................................................................. 1
Optional Accessories ........................................................................................ 1
Installation
Integrated RF EAS Antenna Connection .......................................................... 2
EAS System Connection................................................................................... 3
Checkpoint®EAS System Integration............................................................ 3
Configuration
Imager Configuration for EAS Applications....................................................... 4
Operation
EAS – Tag Deactivation Range ........................................................................ 6
Scanner and Cable Terminations
Scanner Pinout Connections ............................................................................ 8
Cable Connector Configurations....................................................................... 9
Antenna Disconnect.......................................................................................... 9
Limited Warranty ................................................................................................ 10
1
INTRODUCTION
Document Scope
This guide provides additional information required for the installation,
configuration, and operation of MS7580 models equipped with EAS
(MS7580-118-EAS). This guide is intended to be used in conjunction with the
standard MS7580 Genesis, Presentation Area-Imager, Installation and User’s
Guide (PN 00-02290).
Optional Accessories
Cable Compatibility Warning
The MS7580 requires a cable designed for a 12VDC area imager. Do not
attempt to use any cables other than the specified cables listed below.
Any damage incurred from incorrect cable usage will void the limited warranty
shown on page 10.
EAS Cable Options
Part # Description
The following cables are compatible with Checkpoint System devices.
MX-5S000-E-3 RS232 12V VLink Straight, Black Cable
with Built in Power Jack
MX-5S235-E-3 USB 12V VLink Straight Black Cable with
Built in Power Jack, Non-Locking Type A Connector
VLink Power Supply Options
AC to DC Power Transformer - Regulated 12VDC @ 1.25A output.
46-00862 90VAC to 255VAC United States, Canada and Japan
46-00863 90VAC to 255VAC Continental European
46-00864 90VAC to 255VAC United Kingdom
46-00865 90VAC to 255VAC China
46-00866 90VAC to 255VAC Australia
www.metrologic.com2
INSTALLATION
Integrated RF EAS Antenna Connection
The following instructions are applicable for MS7580-118-EAS kits containing an
RS232, MX-5S000-E-3 cable or a USB, MX-5S235-E-3 cable.
Important: Instructions for host cable connections are located in the MS7580
Genesis Installation and User’s Guide (PN 00-02290) under the
Installation section.
1. Locate the connector cover
on the bottom of the imager’s
stand.
2. Remove the socket screw
securing the connector cover.
A 1.5 mm hex key is supplied.
3. Remove the connector cover
plate by lifting up (©) the end and
sliding the cover to the left (§).
4. Insert the 2-pin box plug (A) into
the receptacle on the imager’s
stand (see Figure 2).
5. Insert the cable’s strain relief (B)
into the channel on the stand
(see Figure 2).
6. Re-install the connector cover.
Slide the tab (C) on the cover
into the space between the box
receptacle and the stand
(see Figure 3).
7. Install the socket screw (D) to
secure the cover to the stand
(see Figure 3).
Fi
g
ure
3
.
Figure 2.
Figure 1.
3
INSTALLATION
EAS System Connection
MS7580-118-EAS models are equipped with an integrated antenna for Electronic
Article Surveillance (EAS) system support. The following information should be
used in conjunction with the manufacturer’s documentation provided with the
EAS system.
Checkpoint® EAS System Integration
Metrologic cables compatible with Checkpoint EAS systems include five
additional wires for device connection. Consult the table below for the
appropriate wire and terminal configuration.
Antenna and Interlock†Connection
Cable
(MX-5S000-E-3 or MX-5S235-E-3) Checkpoint Device
Wire Color Wire Gauge Connection Type
Solid Light Green Thin INTLK + Terminal
Solid Black Thin INTLK - Terminal, GND Interlock†
Red and White Thick Antenna + Terminal
Black and White Thick Antenna - Terminal
No Insulation/Shield Antenna Shield
Antenna
† Interlock functionality requires specific EAS device settings. Consult the
manufacturer’s EAS system documentation for the appropriate switch and timing
potentiometer settings.
Inside the Checkpoint device, two switch banks set the deactivation antenna
tuning. The recommended settings for the switch banks are shown below.
See page 6 for tag deactivation guidelines.
Switch Bank Settings
SW1 SW2
Switches 1 - 6 OFF Switches 1 - 6 OFF
Settings of 0pF to 47pF are recommended to achieve a maximum
deactivation range.
Checkpoint®is a registered trademark of Checkpoint Systems, Inc.
www.metrologic.com4
CONFIGURATION
Imager Configuration for EAS Applications
EAS support is disabled by default in the MS7580 series. To enable EAS
support the imager must be configured for a system type and signal mode.
Follow the configuration sequence below to configure the imager for EAS
functionality.
1. Scan the system type bar code below to enable EAS system support.
Enable Checkpoint System EAS Support
³337220
To disable EAS support, scan the Disable EAS Support bar
code below.
Disable EAS Support
³337200
2. Scan either the Enable Continuous Mode bar code or the Enable
Regular Mode bar code.
Enable
Regular Mode
Regular Mode
In regular EAS mode, the imager will signal
the EAS system to activate immediately after
the area imager successfully transmits a bar
code. The area imager will signal the EAS
system to deactivate after the configured
EAS timeout expires.
³146105
Enable
Continuous Mode
Continuous Mode
In continuous mode, the imager will signal
the EAS system to activate when it first
powers on. The area imager will never
deactivate the EAS system while in
continuous mode.
The EAS timeout setting has no effect in
continuous mode.
³146115
5
CONFIGURATION
3. Scan the desired EAS timeout length (applicable for regular mode only).
The EAS timeout length specifies the maximum time that the area
imager will leave the EAS interlock signal asserted following a
successful scan.
If the area imager commonly fails to deactivate EAS tags,
try increasing the value of the timeout setting.
Note: The EAS timeout setting has no effect in continuous
mode.
EAS Timeout 100 ms
³846000
EAS Timeout 500 ms
³846050
EAS Timeout 1s
³8460100
EAS Timeout 5s
³8460500
www.metrologic.com6
OPERATION
EAS – Tag Deactivation Range
Antenna Precaution:
The integrated EAS antenna is built into the stand/base of the imager.
Do not enclose or rest the imager’s base in close proximity to dense
metal. The metal may interfere with the antenna decreasing the
expected deactivation range.
Tag Storage Precaution:
Do not store tags within 45.7 cm [18.0″] of the MS7580. Tags stored
closer than 45.7 cm [18.0″] may be unintentionally deactivated. The
precautionary area includes storage areas located under the MS7580.
Proper tag deactivation requires the entire tag to pass through the expected
tag deactivation range indicated in figures 4 and 5.
Figure 4. Expected Tag Deactivation Area (Side View)
Specifications are subject to change without notice.
Andere Handbücher für Genesis MS7580
2
Inhaltsverzeichnis
Andere Metrologic Barcode-Lesegerät Handbücher
Metrologic
Metrologic MS9590 VOYAGERGS series Bedienungsanleitung
Metrologic
Metrologic MS 1690 Focus Series Bedienungsanleitung
Metrologic
Metrologic Fusion MS3780 Bedienungsanleitung
Metrologic
Metrologic MS6720 Bedienungsanleitung
Metrologic
Metrologic MS9500 Voyager Series Bedienungsanleitung
Metrologic
Metrologic MS7320 InVista Series Bedienungsanleitung
Metrologic
Metrologic MS9530 Series Bedienungsanleitung
Metrologic
Metrologic MS700i Bedienungsanleitung
Metrologic
Metrologic MS 1690 Focus Series Bedienungsanleitung
Metrologic
Metrologic MS7320 InVista Series Bedienungsanleitung
Metrologic
Metrologic MS6130 Bedienungsanleitung
Metrologic
Metrologic MS6200 Pulsar Series Bedienungsanleitung
Metrologic
Metrologic MK9520-37A38 Bedienungsanleitung
Metrologic
Metrologic FocusE IS1650 Bedienungsanleitung
Metrologic
Metrologic MS 1690 Focus Series Bedienungsanleitung
Metrologic
Metrologic MS9520 Voyager Bedienungsanleitung
Metrologic
Metrologic MK1690-61A38 Bedienungsanleitung
Metrologic
Metrologic MS9500 Voyager Series Bedienungsanleitung
Metrologic
Metrologic MS9530 Series Bedienungsanleitung
Metrologic
Metrologic MS6130 MX003 Bedienungsanleitung
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
