Metrologic IS4220 ScanGlove Bedienungsanleitung

METROLOGIC INSTRUMENTS, INC.

IS4220 ScanGlove®

Laser Bar Code Scanner

Installation and User’s Guide

mlpn 2348 cover.qxd 9/21/2004 2:57 PM Page 1

LOCATIONS

CORPORATE HEADQUARTERS

NORTH AMERICA EUROPEAN,MIDDLE EAST &AFRICAN

HEADQUARTERS

USA, NEW JERSEY GERMANY,MUNICH

Metrologic Instruments, Inc. Metrologic Instruments GmbH

Tel: 1-800-ID-METRO Fax: 856-228-6673 Tel: 49-89-89019-0 Fax: 49-89-89019-200

Email: i[email protected] Email: i[email protected]

SOUTH AMERICA,BRAZIL SÃO PAULO GERMANY,MUNICH

Metrologic do Brasil Ltda. Metrologic Instruments GmbH

Tel: 55-11-5182-8226 Fax: 55-11-5182-8315 Tel: 49-89-89019-0 Fax: 49-89-89019-200

Email: i[email protected] Email: i[email protected]

SOUTH AMERICA,OUTSIDE BRAZIL SÃO PAULO ITALY,BOLOGNA

Metrologic South America Metrologic Instruments Italia srl

Tel: 55-11-5182-7273 Fax: 55-11-5182-7198 Tel: +39 0 51 6511978 Fax: +39 0 51 6521337

Email: i[email protected] Email: i[email protected]

ASIA,SINGAPORE FRANCE,PARIS

Metrologic Asia (Pte) Ltd Metrologic Eria France SA

Tel: 65-6842-7155 Fax: 65-6842-7166 Tel: +33 (0) 1 48.63.78.78

Email: [email protected]c.com Fax: +33 (0) 1 48.63.24.94

Email: i[email protected]

CHINA,SUZHOU

Metro Technologies Co., Ltd. SPAIN,MADRID

Tel: 86-512-62572511 Fax: 86-512-62571517 Metrologic Eria Ibérica, SL

Email: [email protected]ogic.com Tel: +34 913 272 400 Fax: +34 913 273 829

Email: i[email protected]

Metro Sales Office

Tel: 86-512-67622550 Fax: 86-512-67622560 Metrologic Europe Repair Center (MERC)

Email: [email protected] Metrologic Eria Ibérica, SL

Tel: +34 913 751 249 Fax: +34 913 270 437

JAPAN,TOKYO

Metrologic Japan Co., Ltd. UNITED KINGDOM,BASINGSTOKE

Tel: 81-03-3839-8511 Fax: 81-03-3839-8519 Metrologic Instruments UK Limited

Email: [email protected]ogic.com Tel: +44 (0) 1256 365900

Fax: +44 (0) 1256 365955

Email: i[email protected]etrologic.com

USSIA,MOSCOW

Metrologic Russia

Tel: +7 095 730 7424 Fax: +7 095 730 7425

Email: i[email protected]

transmitted, or stored in any form or by any means without prior written consent, except by reviewer, who

may quote brief passages in a review, or provided for in the Copyright Act of 1976.

Products and brand names mentioned in this document are trademarks of their respective companies.

iii

TABLE OF CONTENTS

Introduction .......................................................................................................... 1

Scanner and Accessories .................................................................................... 1

Scanner Installation.............................................................................................. 2

Scanner Configuration to the Host System .......................................................... 3

Parts of the Scanner ............................................................................................ 4

Visual Indicators................................................................................................... 5

Audible Indicators................................................................................................. 9

Labels................................................................................................................. 10

Maintenance....................................................................................................... 10

Infrared (IR) Object Sensor ................................................................................ 11

Scan Field .......................................................................................................... 12

Specifications ..................................................................................................... 13

Default Settings.................................................................................................. 14

Troubleshooting Guide....................................................................................... 19

Limited Warranty................................................................................................ 20

Notices ............................................................................................................... 21

Patents ............................................................................................................... 23

Index................................................................................................................... 24

INTRODUCTION

The IS4220 ScanGlove®is a fully automatic single-line laser barcode scanner.

It is designed to be used as a “hands-free” wearable scanner or a stationary

desktop scanner.

Every ScanGlove is equipped with ScanQuest®, a patented activation technology

that allows the scanner to read bar codes automatically as the operator presents

the bar code to the scanner. Additional features include; 52 scan lines a

second, short or long range activation and two universal glove sizes with left and

right-hand capabilities.

The IS4220 has built in decoding for applications that use a RS232, Keyboard

Wedge, Stand Alone Keyboard, Light Pen Emulation, or USB communication

interface. For additional information on other system interfaces call please call a

Metrologic Customer Service Representative at 1-800-ID-METRO.

SCANGLOVE MODEL NO. INTERFACE

IS4220-07 USB Keyboard

IS4220-08 USB POS

IS4220-14 RS232

IS4220-15 Light Pen Emulation

IS4220-17 PC Keyboard Wedge and Stand Alone Keyboard

IS4220-41 Full RS232 and Light Pen Emulation

SCANNER AND ACCESSORIES

PART NUMBER DESCRIPTION

IS4220 IS4220 Laser Scanner

00-02348 Installation and User’s Guide

00-02343 Programming Guide

00-02044 Programming Addendum (USB Models Only)

45-45455 Black Adjustable Glove

If any item is missing or to order additional items, contact the dealer, distributor or call

Metrologic’s Customer Service Department at 1-800-ID-METRO or 1-800-436-3876.

SCANNER INSTALLATION

1. Turn off power to the host system.

2. Connect the communication cable to the proper port on the host device.

3. Turn on power to the host system.

When the IS4220 first receives power, the red LED will flash, the

green LED will flash, and then the scanner will beep once.

Caution:

To maintain compliance with applicable standards, all circuits connected

to the scanner must meet the requirements for SELV (Safety Extra Low

Voltage) according to EN 60950.

To maintain compliance with standard CSA C22.2 No. 950/UL 1950 and

norm EN 60950, the power source should meet applicable performance

requirements for a limited power source.

To maintain compliance with federal regulations 21 CFR, Part 1040.10,

section (f)(6) the scanner must be plugged into an electrical outlet with a

switch accessible to the user or be powered by a host system containing

a switch that will disable power to the scanner.

SCANNER CONFIGURATION TO THE HOST SYSTEM

The IS4220 is shipped from the factory pre-programmed to a set of default

parameters. It may be necessary to change the default parameters to match the

host system’s requirements or to enable additional scanner functions. For a list

of possible parameter settings, refer to the Default Settings section of this guide.

Important notes for the -07 and -08, IS4220 USB Interfaces.

The IS4220-07 and the IS4220-08 are pre-programmed for USB

Emulation before leaving the factory. If the recall defaults bar code is

scanned the unit must be re-programmed for USB Emulation before

enabling or disabling any additional features documented in the

programming guide (MLPN 00-02343).

To re-program the unit for USB Keyboard Emulation or USB POS

Emulation refer to the IS4220 USB Addendum (MLPN 00-02044)

for the IS4220 Programming Guide.

To modify the scanner’s default parameters follow the steps below using the bar

codes located in the programming guide (MLPN 00-02343).

1. Scan the

ENTER PROGRAM MODE bar code to enter programming mode. The

scanner will beep three times.

2. Scan the bar code(s) for the desired parameter(s). The scanner will beep

once.

3. Scan the

EXIT PROGRAM MODE bar code to exit and save the new parameter

settings. The scanner will beep three times.

If during programming there is a need to return the scanner to the

original factory settings, scan the recall defaults bar code in the

programming guide. All settings selected during that session or any

previous sessions are discarded when you scan the recall defaults

code.

Please read the warning above for the IS4220-07 and -08 models

before using the recall defaults bar code.

PARTS OF THE SCANNER

Figure 1. Scanner Parts

Item

No. Description



Green LED

When a bar code is read successfully the green LED will flash.



Red LED

When the red LED is illuminated, the laser is on.



Red Output Window (Laser Aperture)



Infrared Sensor (IR)

If a specified time has elapsed without any scanning, the unit will

enter a “standby” mode. To reactivate the unit, place an object in

front of the IR sensor. The red LED will turn on when the scanner

is ready to scan.



Communication/Power Cable

This cable’s termination is application dependent.

VISUAL INDICATORS

There is a red and a green LED located on the top of the scanner. When the

scanner is on, the flashing or constant illumination of the LEDs indicates the

status of the current scan and the scanner.

No Red LED Illumination of the LEDs will not occur if the scanner has

remained dormant for a specified time and the scanner is

not receiving power from the host. To reactivate the unit,

direct the output window up then down toward the object.

Red Flash;

Green Flash;

Steady Red

When the scanner first receives power, the red LED will

flash, followed by the green LED, and then the unit will

beep once. The red LED will stay on after it flashes once.

Steady Red When the laser is on, the red LED will be on. This occurs

when an object is detected in the scan field. If the scanner

cannot detect a bar code within approximately 2.5

seconds, the unit will go into a standby mode and the red

LED will shut off indicating that the laser is no longer on.

Steady Red

LED; Green

Flash

When the scanner successfully reads a bar code, the

green LED will flash and the unit will beep once. If the

green LED does not flash or the scanner does not beep,

then the bar code was not successfully read.

Repetitive Red

LED Flashing

When the red LED flashes several times while it rests

upon a stationary surface, then an object is within the scan

field and is activating the IR sensor repetitively.

To eliminate this disturbance, direct the scan window

toward a different location.

Steady Green

LED

After a successful scan, the scanner transmits the data to

the host device. When the host is not ready to receive the

information, the green LED will remain on until data can

transmit.

SIGNAUX OPTIQUES

Sur la partie supérieure du scanner se trouvent une diode LED rouge et une

diode LED verte. Quand le scanner est sous tension, les diodes rouge et verte

clignotantes ou allumées vous informent sur l'état de palpage et de scanner.

Ni la diode

rouge, ni la

diode verte

n'est allumée

Il existe deux raisons possibles pour que les diodes ne

s'allu-ment pas. Si le scanner ne reçoit pas d'énergie de

l'ordinateur PC, les diodes ne s'allument pas. Quand le

scanner reçoit de l'énergie et ne s'allume cependant pas,

le scanner est resté pendant une certaine période sans

être utilisé et le laser et lemoteur sont désactivés. Pour

réactiver l'unité, déplacer un objet devant le palpeur

infrarouge ou prendre le scanner et diriger la fenêtre de

palpage vers le bas.

Diode rouge

clignotante;

diode verte

clignotante;

diode rouge

reste allumée

Quand le scanner reçoit pour la première fois de l'énergie,

la diode rouge se met d'abord à clignoter, puis la diode

verte. Ensuite, le scanner émet un bip sonore unique. Une

fois cette séquence de démarrage effectuée, la diode

rouge reste allumée pendant un certain temps indiquant

que le laser est en service. Quand le scanner ne détecte

aucun objet, la diode rouge et le laser s'éteignent.

Diode rouge

reste allumée

Quand le laser est activé, la diode rouge s'allume

également. C'est par exemple le cas quand un objet se

trouve devant la fenêtre de palpage. Si, en l'espace de 2,

5 secondes, aucun code barres n'est détecté, la diode

rouge s'éteint, ce qui signifie que le laser est désactivé.

Diode rouge

reste allumée;

diode verte

clignotante

Après lecture avec succès d'un code barres par le

scanner, la diode verte se met à clignoter, suivie d'un bip

sonore unique. Si la diode verte ne clignote pas ou quand

aucun bip sonore n'est émis, cela signifie que le code

barres n'a pas pu être lu avec succès.

Clignotement

répété de la

diode rouge

Quand la diode rouge clignote plusieurs fois pendant que

l'appareil repose sur une surface non déplacée, un objet

activant le palpeur infrarouge se trouve devant la fenêtre

de palpage. Ceci peut se produire même quand le

scanner se trouve sur une table ou un reposoir. Pour

éliminer ce défaut, positionner le scanner de façon

différente.

Diode verte

reste allumée

Une fois le palpage effectué avec succès, le scanner

transmetles donnéesà l'ordinateur PC. Si ce dernier n'est

pas prêt à recevoir les données, la diode verte du scanner

s'allume jusqu'à ce que les donnés puissent être

transmises.

Andere Handbücher für IS4220 ScanGlove

Inhaltsverzeichnis

Andere Metrologic Barcode-Lesegerät Handbücher

Metrologic

Metrologic MS7620 Bedienungsanleitung

Metrologic

Metrologic MS7820 Solaris Bedienungsanleitung

Metrologic

Metrologic StratosS MS2220 Bedienungsanleitung

Metrologic

Metrologic MS6720 Bedienungsanleitung

Metrologic

Metrologic IS421X ScanGlove Bedienungsanleitung

Metrologic

Metrologic IS3480 QuantumE Bedienungsanleitung

Metrologic

Metrologic StratosS MS2220 Bedienungsanleitung

Metrologic

Metrologic Orbit MS7100 Bedienungsanleitung

Metrologic

Metrologic MS 1690 Focus Series Bedienungsanleitung

Metrologic

Metrologic MS5100 Eclipse Series Bedienungsanleitung

Metrologic

Metrologic TECH 7 Bedienungsanleitung

Metrologic

Metrologic MS9530 Series Bedienungsanleitung

Metrologic

Metrologic IS4225 ScanGlove Bedienungsanleitung

Metrologic

Metrologic MS863 Bedienungsanleitung

Metrologic

Metrologic MS1633 FocusBT Bedienungsanleitung

Metrologic

Metrologic MetroSelect Bedienungsanleitung

Metrologic

Metrologic StratosS MS2222 Bedienungsanleitung

Metrologic

Metrologic MS9520 Voyager Bedienungsanleitung

Metrologic

Metrologic MS7120 Orbit Bedienungsanleitung

Metrologic

Metrologic Hand-Held Scanner Bedienungsanleitung

Metrologic

Metrologic 1070 Bedienungsanleitung

Metrologic

Metrologic Cubit MS6520 Series Bedienungsanleitung

Metrologic

Metrologic Cubit IS6520 Series Bedienungsanleitung

Metrologic

Metrologic MS7600 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung