Metrologic MS6200 Pulsar Series Bedienungsanleitung

METROLOGIC INSTRUMENTS, INC.

MS6200 Pulsar®Series

Single-Line Hand-Held Laser Scanner

Installation and User’s Guide

LOCATIONS

Corporate Headquarters

North America Metrologic Instruments, Inc. Customer Service: 1-800-ID-METRO

90 Coles Road Tel: 856-228-8100

Blackwood, NJ 08012-4683 Fax: 856-228-6673

Email: [email protected]

Internet: www.metrologic.com

European Headquarters

Germany, Metrologic Instruments GmbH Tel: +49 89 89019 0

Middle East and Africa Dornierstrasse 2 Fax: +49 89 89019 200

82178 Puchheim b. Email: info@europe.metrologic.com

Munich, Germany Germany Email: in[email protected].com

Spain Metrologic Eria lbérica SL Tel: +34 913 272 400

Julián Camarillo 29, D-1 Fax: +34 913 273 829

Edificio Diapasón Email: [email protected]

28037 Madrid

Italy Metrologic Instruments Italia srl Tel: +39 0 51 6511978

Via Emilia 70 Fax: +39 0 51 6521337

40064 Ozzano dell’Emilia (BO) Email: [email protected]

France Metrologic Eria France SA Tel: +33 (0) 1 48.63.78.78

69 Rue de la Belle Etoile Fax: +33 (0) 1 48.63.24.94

ZI Paris Nord II, BP 50057 Email: [email protected]

95947 – ROISSY CDG CEDEX

United Kingdom Metrologic Instruments UK Limited Tel: +44 (0) 1256 365900

58 Tempus Business Centre Fax: +44 (0) 1256 365955

Kingsclere Road, Basingstoke Email: info@uk.metrologic.com

Hampshire RG21 6XG

Asia

Singapore Metrologic Asia (Pte) Ltd Tel: 65-6842-7155

No. 8 Kaki Bukit Place Fax: 65-6842-7166

4th Floor Email: [email protected]ic.com

Singapore 416186

China Metro (Suzhou) Technologies Co., Ltd. Tel: 86-512-62572511

221 Xing Hai Street Fax: 86-512-62571517

Suzhou Industrial Park Email: info@cn.metrologic.com

Suzhou, China

215021

Japan Metrologic Japan Co., Ltd. Tel: 81-03-3839-8511

Matsunoya Building, 6 Floor Fax: 81-03-3839-8519

3-14-8 Higashiueno Email: info@jp.metrologic.com

Taitou-Ku, Tokyo 110-0015 Japan

South America

Brazil Metrologic do Brasil Ltda. Tel: 55-11-5182-8226

Rua da Paz 2059 Fax: 55-11-5182-8315

CEP 04713-002 Email: info@br.metrologic.com

Chácara Santo Antônio

São Paulo, SP, Brasil

Outside Brazil Metrologic South America Tel: 55-11-5182-7273

Rua da Paz 2059 Fax: 55-11-5182-7198

CEP 04713-002 Email: info@sa.metrologic.com

Chácara Santo Antônio

São Paulo, SP, Brasil

in any form or by any means without prior written consent, except by reviewer, who may quote brief passages in a review,

or provided for in the Copyright Act of 1976.

Products and brand names mentioned in this document are trademarks of their respective companies.

iii

TABLE OF CONTENTS

Introduction........................................................................................................... 1

Accessories and Supplies .................................................................................... 2

Quick Start............................................................................................................ 3

Standard Scanner Installation .............................................................................. 4

Keyboard Wedge Installation................................................................................ 5

Disconnecting the PowerLink Cable from the Scanner ........................................ 7

Scanner Parts....................................................................................................... 8

Audible Indicators................................................................................................. 9

Visual Indicators ................................................................................................. 10

Failure Modes..................................................................................................... 11

Scan Area........................................................................................................... 12

Labels................................................................................................................. 13

Maintenance....................................................................................................... 13

Troubleshooting Guide ....................................................................................... 14

RS-232 Demonstration Program ........................................................................ 18

Appendix A

Specifications ................................................................................................. 19

Appendix B

Default Settings .............................................................................................. 21

Appendix C

Scanner Pinout Connections .......................................................................... 25

Cable Connector Configurations .................................................................... 26

Appendix D

Warranty and Disclaimer ................................................................................ 28

Appendix E

Notices ........................................................................................................... 29

Appendix F

Patent Information .......................................................................................... 31

Index................................................................................................................... 32

INTRODUCTION

The MS6220 Pulsar®is an entry-level hand held contact laser bar code scanner

that combines the high-speed and accuracy of a laser scanner with the working

range and price of a typical CCD.

Pulsar has a controlled 7.6 cm (3”) depth of field on 100% UPC bar codes, which

makes it perfect for large retail applications where UPC/EAN bar codes are

frequently scanned at less demanding, low-volume check-out areas or satellite

cash registers.

The MS6220 Pulsar is equipped with PowerLink user-replaceable cables, utilizes

MetroSelect®configuration bar codes and is MetrOPOS™ compatible.

Scanner Interface

MS6220-9 OCIA

MS6220-11 IBM 468X/469X

MS6220-41 Full RS-232/Light Pen Emulation

MS6220-47 Keyboard Wedge, Stand-Alone Keyboard and RS232

Transmit/Receive

ACCESSORIES AND SUPPLIES

The following is a list of parts that may or may not be included in a MS6220 kit.

•MS6220 Pulsar®Single-Line Contact Laser Scanner

•AC to DC Power Transformer – Regulated 5.2VDC @ 650 mA output

•One of the following may be included:

•120 V United States [ MLPN 45-45593 ]

•220 V - 240 V Continental European [ MLPN 45-45591 ]

•220 V – 240 V United Kingdom [ MLPN 45-45592 ]

•PowerLink Cable with built in power jack.

•One of the following may be included:

•Standard – 2.1 m (7’) straight cord, short strain relief

[ MLPN 54-54000 ]

•Optional – 2.7 m (9’) coiled cord, long strain relief

[ MLPN 53-53000 ]

•Keyboard Wedge PowerLink Cable Kit [ MLPN 53-53002 or 54-54002 ]

•A PowerLink “ Y” Cable with a 5-pin DIN female connector and a 6-pin

mini DIN male connector

•An Adapter Cable with a 5-pin DIN male connector and a 6-pin mini

DIN female connector

•Installation and User’s Guide [ MLPN 00-02447 ]

•Scanner Custom Configuration Guide

•MetroSelect®Single Line Configuration Guide [ MLPN 00-02544 ]

Other items may be ordered for the specific protocol being used. To order

additional items, contact the dealer, distributor or call Metrologic’s Customer

Service Department at 1-800-ID-METRO or 1-800-436-3876.

QUICK START

1. Connect the 10-pin RJ45 male connector into the jack on the Pulsar®

MS6220. You will hear a ‘click’ when the connection is made.

2. Connect the L-shaped plug of the power supply into the power jack on the

PowerLink cable.

3. Connect the power supply into an AC outlet. Make sure the AC input

requirements of the power supply match the AC outlet.

(See caution statement below)

4. When the MS6220 is ready to scan, the green LED will turn on, the red LED

will flash and the scanner will beep once.

5. The MS6220 ‘s operation is automatic. The laser pulses on and off. The

green LED remains on during normal pulse operation and it blinks during

power save mode.

Operational Test

6. Place a bar code in front of the scanning window. The scanner will beep

once and flash the red LED if the bar code was successfully decoded.

7. The scanner is shipped from the factory programmed with default settings.

To configure the MS6220 scanner to meet the host system’s specific needs,

refer to the Programming Guide or custom configuration guide for

instructions on how to change the scanners default settings.

Caution:

To maintain compliance with federal regulations 21 CFR, Part 1040.10, section (f)(6) the scanner

must be plugged into an electrical outlet with a switch accessible to the user or be powered by a host

system containing a switch that will disable power to the scanner.

STANDARD SCANNER INSTALLATION

1. Turn off the host system.

2. Connect the 10-pin RJ45 male connector of the PowerLink cable into the

jack on the MS6220.

Note: If the MS6220 is receiving power from the host system, skip to step

#5. (See caution statement below*)

3. Connect the L-shaped plug of the power supply into the power jack on the

PowerLink cable. (See caution statement below**)

4. Make sure the AC input requirements of the power supply match the AC

outlet. Connect the power supply into an AC outlet.

5. Connect the PowerLink cable to the proper port on the host system.

6. Turn on the host system

7. When the MS6220 is ready to scan, the green LED will turn on, the red LED

will flash and the scanner will beep once.

Manufacturer’s Note:

Plugging the scanner into a port on the host system does not guarantee that the

scanned information will be communicated properly to the host system. The

scanner and/or the host system may need to be configured for communications

to occur.

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must meet

the requirements for SELV (Safety Extra Low Voltage) according to EN 60950.

*To maintain compliance with standard CSA C22.2 No. 950/UL 1950 and norm EN 60950, the power

source should meet applicable performance requirements for a limited power source.

**To maintain compliance with federal regulations 21 CFR, Part 1040.10, section (f)(6) the scanner

must be plugged into an electrical outlet with a switch accessible to the user or be powered by a host

system containing a switch that will disable power to the scanner.

KEYBOARD WEDGE INSTALLATION

1. Turn off the host system.

2. Connect the 10-pin RJ45 male connector of the PowerLink cable into the

jack on the MS6220.

3. Connect the L-shaped plug of the power supply into the power jack on the

PowerLink cable (refer to the manufacturer’s recommendation on page 6).

4. Make sure the AC input requirements of the power supply match the AC

outlet. Connect the power supply into an AC outlet (see caution statement

below**).

5. Disconnect the keyboard from the host system.

6. The PowerLink “Y” cable is terminated with a 5-pin DIN female connector on

one end, and a 6-pin mini DIN male on the other. Metrologic will supply an

adapter cable with a 5-pin DIN male connector on one end and a 6-pin mini

DIN female connector on the other. According to the termination required,

connect the appropriate end of the adapter cable to the PowerLink “Y” cable,

leaving the necessary termination exposed for connecting to the keyboard

and the keyboard port on the host system.

7. Connect the PowerLink “Y” cable to the keyboard and keyboard port on the

host system.

8. Power up the host system.

9. When the MS6220 is ready to scan, the green LED will turn on, the red LED

will flash and the scanner will beep once.

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must meet

the requirements for SELV (Safety Extra Low Voltage) according to EN 60950.

*To maintain compliance with standard CSA C22.2 No. 950/UL 1950 and norm EN 60950, the power

source should meet applicable performance requirements for a limited power source.

**To maintain compliance with federal regulations 21 CFR, Part 1040.10, section (f)(6) the scanner

must be plugged into an electrical outlet with a switch accessible to the user or be powered by a host

system containing a switch that will disable power to the scanner

KEYBOARD WEDGE INSTALLATION (CONTINUED)

Manufacturer’s Recommendation

If the keyboard port of the host system cannot supply enough current, the

use of an external power supply with the MS6220 Keyboard Wedge will be

necessary. Powering the MS6220 directly from the computer keyboard

connector could interfere with the operation of the scanner or the computer.

Not all computers supply the same current through the keyboard port, so a

scanner may work on one computer and not another (see caution statement

on page 5).

Andere Handbücher für MS6200 Pulsar Series

Inhaltsverzeichnis

Andere Metrologic Barcode-Lesegerät Handbücher

Metrologic

Metrologic StratosS MS2220 Bedienungsanleitung

Metrologic

Metrologic IS3480 QuantumE Bedienungsanleitung

Metrologic

Metrologic MS9500 Voyager Series Bedienungsanleitung

Metrologic

Metrologic MS7120 Orbit Bedienungsanleitung

Metrologic

Metrologic MS770 Bedienungsanleitung

Metrologic

Metrologic MS9590 VOYAGERGS series Bedienungsanleitung

Metrologic

Metrologic MS6130 MX003 Bedienungsanleitung

Metrologic

Metrologic MS9500 Voyager Series Bedienungsanleitung

Metrologic

Metrologic 160 Benutzerhandbuch

Metrologic

Metrologic Stratos MS2x20 Series Montage- und Bedienungsanleitung

Metrologic

Metrologic MS7600 Bedienungsanleitung

Metrologic

Metrologic MS 1690 Focus Series Bedienungsanleitung

Metrologic

Metrologic MLPN 2168 Bedienungsanleitung

Metrologic

Metrologic MS9500 Voyager Series Bedienungsanleitung

Metrologic

Metrologic 1070 Bedienungsanleitung

Metrologic

Metrologic MS9520 Voyager Bedienungsanleitung

Metrologic

Metrologic MS 1690 Focus Series Bedienungsanleitung

Metrologic

Metrologic MS6130 Bedienungsanleitung

Metrologic

Metrologic TECH 8 Bedienungsanleitung

Metrologic

Metrologic IS4220 ScanGlove Bedienungsanleitung

Metrologic

Metrologic MS860 Bedienungsanleitung

Metrologic

Metrologic MS7820 Solaris Bedienungsanleitung

Metrologic

Metrologic Cubit IS6520 Series Bedienungsanleitung

Metrologic

Metrologic MS9530 Series Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung