MFJ SWR/Wattmeter MFJ-864 HF/144/440 Bedienungsanleitung

Inhaltsverzeichnis

Andere MFJ Messgerät Handbücher

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

MFJ-862 SWR/Wattmeter

1

MFJ-864 HF/144/440 SWR/Wattmeter





General Information:

The MFJ-864 HF/144/440 SWR/Wattmeter measures forward and reflected

power and indicates SWR for the 1.8 -60, 144, and 440 MHz ham bands.

The MFJ-864 has 2 power scales for each band selected with the front panel

rotary switch. The low power scale reads from 0-30 watts forward and 0-6

watts reflected. The high power reads from 0-300 watts forward and 0-60

watts reflected. SWR is indicated from 1:1 to 5:1.

MFJ-864 Theory of Operation:

The MFJ-864 senses RF energy traveling along a 50 ohm stripline. A

forward and reflected stripline couple to the 50 ohm stripline to make a

directional coupler. A voltage is produced in the forward and reflected

striplines that is proportional to the current and voltage traveling along the 50

ohm stripline. This signal is rectified by a diode and smoothed by a capacitor.

Because the directional coupler's sensitivity increases with frequency,

trimpots are used to adjust for different frequency and power settings (high or

low power).

Connections:

Connect your HF transmitter and antenna to the 1.8 - 60 MHz HF Sensor

connectors labeled XMTR and ANT on the rear panel. Connect your

VHF/UHF transmitter and antenna to the 144 / 440 MHz VHF/UHF Sensor

connectors labeled TRANSMITTER and ANTENNA on the rear panel. It is

important that you use good quality coax and connectors that are

designed for HF and VHF/UHF!

If you want to measure the power capability of a transmitter/amplifier or to re-

calibrate the MFJ-864 you should connect a quality dummy load (50 ohms)

that is designed for VHF/UHF to the antenna jack.

MFJ-862 SWR/Wattmeter

2

The MFJ-864 has a lighted meter. To provide power for the meter light, a 12

Vdc supply such as the MFJ-1312B should be used. Use a standard 2.1 mm

coaxial plug with the center conductor positive and the sleeve ground.

Using the MFJ-864:

To measure forward and reflected power turn the selector switch to the

correct frequency and power setting. Transmit and read the power from the

meter. Each unmarked hatch on the scale is an even division between the

two marked numbers. SWR is read directly from the scale where the meter

needles cross.

If a more exact reading for SWR is needed you may use the equation for

SWR. Measure the forward and reflected power and put the values into the

following equation:

Calibration:

Note that the readings for forward and reflected power (and thus SWR) are

less accurate if the power levels you are reading are not near the calibration

power level or within the correct power range. For an accurate reading of 10

watts forward use the low power scale. If your transmitter only transmits 10

watts, re-calibrate the low power scale at 10 watts for maximum accuracy.

The MFJ-864 has been calibrated at the factory for 10 and 100 watts. If re-

calibration is necessary you will need a 50 ohm dummy load, good quality 50

ohm coax, and a transmitter of known power or another accurate wattmeter

to use as a standard.

Connect the transmitter to the TRANSMITTER connector and a good length

of coax between the ANTENNA connector and the dummy load. Transmit at

a known power level and adjust the forward or reflected sensitivity pot, for the

power scale and frequency you are using, until the correct reading is shown

on the meter.

SWR = 1 + Pr

Pf 1- Pr

Pf

Pr = Reflected Power

Pf = Forward Power

F

H

G

I

K

J

F

H

G

I

K

J

MFJ-862 SWR/Wattmeter

3

Meter Calibration

If the zero adjustment of your wattmeter should ever need to be re-adjusted,

it is a simple procedure. The meter should be re-zeroed whenever a pointer

is more than 2 pointer widths from the "0" mark.

To re-zero the pointer, first you must remove the meter from the chassis.

Remove the screws from the meter tabs from either the front or the inside of

the unit. Next carefully remove the

clear plastic front by grasping it on both

sides.

Use a pair of needle nose pliers to turn

the zero adjustment lever. Turn

clockwise to lower the needle or

counterclockwise to raise the pointer.

Adjustment is very sensitive and

should require little force. Replace the

meter cover and reinstall the meter into

the chassis.

Technical Assistance:

If you have any problem with this unit first check the appropriate section of

this manual. If the manual does not reference your problem or your problem

is not solved by reading the manual you may call MFJ at 601-323-5869. You

will be best helped if you have your unit, manual and all information on your

station handy so you can answer any questions the technicians may ask.

You can also send questions by mail to MFJ Enterprises, INC., P.O. Box 494,

Mississippi State, MS 39762; by FAX to 601-323-6551; through Compuserve

at 76206,1763; or by email to 76206.1763@Compuserve.com. Send a

complete description of your problem, an explanation of exactly how you are

using your unit, and a complete description of your station.

MFJ-862 SWR/Wattmeter

4

Schematic: