Microchip Technology ATF15 Series Bedienungsanleitung

ATF15xx CPLD ISP Software [ATMISP] –Quick Start Tutorial P. 1

ATF15xx CPLD ISP Software - ATMISP

Quick Start Tutorial

This tutorial introduces the features and usage of the ATF15xx CPLD In-System

Programming (ISP) Software [ATMISP] v7.x for the ATF15xx family of JTAG ISP

supported Complex Programmable Logic Devices (CPLDs). It describes the entire ISP

process from setting up the JTAG device chain file (.CHN) using ATMISP to executing the

JTAG ISP instructions onto the JTAG device on the target JTAG ISP hardware system. For

this tutorial, the ATF15xx-DK3 CPLD Development/Programmer board will be used along

with the ATDH1150USB USB based ATF15xx JTAG ISP cable. Please refer to the Getting

Started section of the ATMISP Help File for information on how to setup other ISP hardware

platforms.

Step I : Setup ISP Hardware

For this section of the tutorial, the ATF15xx-DK3CPLD Development/Programmer board is

used as the target ISP hardware along with the ATDH1150USB cable. To setup the

ATF15xx-DK3 and ATDH1150USB for programming, follow the steps below.

1. Connect the USB cable contained in the ATDH1150USB kit to the USB port of the

computer and the USB connector of the ATDH1150USB ISP cable.

2. Connect the 10-wire ribbon cable contained in the kit to the JTAG-A port of the

ATDH1150USB and to the JTAG header (JTAG-IN) of the ATF15xx

Development/Programmer board.

NOTE: The selection jumper at JP-TDO on the ATF15xx-DK3 board should be plugged into

the “TO ISP CABLE” side.

USB

ATF15xx

CPLD

7-segment Displays

Push Button Switches

LEDs

OSC

JTAG-A

ATDH1150USB

ATF15xx-DK3

JTAG-IN

ATF15xx CPLD ISP Software [ATMISP] –Quick Start Tutorial P. 2

3. Insert the 44-TQFP socket adapter board (ATF15xx-DK3-SAA44) onto main ATF15xx-

DK3 board if it is not already inserted.

4. Set both the VccIO and VccINT selection jumpers on the ATF15xx-DK3 board to 3.3V.

NOTE: The Power Switch for the ATF15xx-DK3 must be turned OFF before changing the

positions of the VccIO and VccINT Selection jumpers.

5. Connect the 9V DC power source to the power connector at JPower of the ATF15xx-DK3

board.

6. Insert a blank ATF1504ASV 44-pin TQFP device into the 44-pin TQFP socket. Please

note that pin 1 of the device should be at the upper left hand corner of the socket facing

the U1 label.

7. Turn the power on by bringing the Power Switch of the ATF15xx-DK3 board to the ON

position.

For the older ATF15xx CPLD ISP kits, please refer to the corresponding User Guide for

information on how to setup the hardware to perform JTAG ISP operations. For custom

JTAG ISP target hardware systems, please connect the JTAG ISP download cable into the

appropriate connector and apply Vcc to the CPLD(s) and JTAG ISP download cable.

The ISP hardware setup process is now completed.

Step II : Setup ATMISP Software

The first step of an ISP flow is to create a new chain file in the ATMISP software. A chain

file (.CHN) contains the JTAG device chain information such as the device types, number of

devices in JTAG chain, JTAG operations, and the location of the associated JEDEC files that

are required to program a single or multiple-device JTAG chain in the target hardware

system.

1. To create a new chain file, the ATMISP software first needs to be launched either

through the desktop icon or the Start … Programs menu.

2. To create a new chain file, select the New command under the File menu or click on the

New shortcut button.

An existing chain file (with a .CHN extension) that was created by the ATMISP software

can be loaded into the software by using the Open command under the File menu or

the Open shortcut button.

ATF15xx CPLD ISP Software [ATMISP] –Quick Start Tutorial P. 3

3. The first piece of information that the software asks for when creating a new chain is the

number of devices in the JTAG hardware chain. Therefore, simply enter how many JTAG

devices are chained together in your target system. For this tutorial, enter 1and then

click OK since you will be programming a 1-device JTAG chain in Step III of this tutorial

using the ATF15xx CPLD Development/Programmer board.

4. Next you will need to specify the properties of each JTAG device in the Device Properties

window. First, you will need to select the target device type of the first device in the

JTAG chain. Clicking on the down arrow will open the list of all the supported device

types. For this tutorial, please select ATF1504ASV as the target device type.

In the JTAG Instruction field, you can specify which JTAG instruction to be executed on

this device in the chain. Please select Program/Verify to program and verify the

ATF1504ASV.

The next step is to specify the JEDEC file to be programmed into the target device in the

JEDEC File field. Click on the Browse button, change the directory to the

[..\JEDEC\ATF1504AS] sub-directory under the ATMISP installation directory and

then select atf1504.JED as the JEDEC file. Click OK to close the JTAG Device

Properties window when all properties are specified.

If there is more than one device in the JTAG chain, then the JTAG Device Properties

window will open again for the second device, third device, and so on until the JTAG

Device Properties window for the last device in the JTAG chain is closed.

A new chain is now created and it will be displayed in the Chain File Hierarchy window

of the ATMISP Software. You can easily add or delete devices by using the Add Device

or Delete Device command respectively. These two commands are available through

the Edit menu and the right-click drop down menu in the Chain File Hierarchy window.

To edit the device properties, you can use the Edit Device command in the Edit menu

or by double clicking any part of the chain in the Chain File Hierarchy window.

ATF15xx CPLD ISP Software [ATMISP] –Quick Start Tutorial P. 4

5. For ATMISP v7.x, the only cable type supported is the ATDH1150USB USB based

ATF15xx JTAG ISP cable and the only port type supported is USB (v1.1/2.0/3.0). If you

are using an LPT based JTAG ISP cable (i.e. ATDH1150VPC), please use ATMISP v6.x on

a Windows 2K or XP PC instead.

6. This chain file can now be saved by selecting the Save or Save As command in the File

menu or by clicking on the Save shortcut button. Saving the chain file is optional but

recommended.

This completes the ATMISP software setup process.

Step III : Execute ISP Instructions

Now that both the ISP software and hardware are properly setup, it is time to program the

JEDEC file [atf1504.JED] into the target CPLD [ATF1504ASV] on the target ISP board

[ATF15xx-DK3]. To start the ISP process, click on the Run button at the bottom of the

ATMISP window.

The programming process will now start and the progress bar will indicate the progress of

the programming cycle. Once the programming is completed, ATMISP will generate a

prompt indicating that the JTAG operation was completed successfully or not. The message

pane at the bottom will also show the information related to the programming process.

However, the atf1504.jed file was not created to show any meaningful display on the LEDs

of the ATF15xx-DK3.

PLD Technical Support:

Email -

pld@microchip.com

Online Support Form -

www.microchip.com/technical-support

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Microchip Technology Hauptplatine Handbücher

Microchip Technology

Microchip Technology ATmega328P Xplained Mini Bedienungsanleitung

Microchip Technology

Microchip Technology BM62 Bedienungsanleitung

Microchip Technology

Microchip Technology EVB-USB7056 Bedienungsanleitung

Microchip Technology

Microchip Technology dsPICDEM 1.1 Bedienungsanleitung

Microchip Technology

Microchip Technology PICDEM Bedienungsanleitung

Microchip Technology

Microchip Technology MCP2515 Bedienungsanleitung

Microchip Technology

Microchip Technology EVB-USB4x12 Bedienungsanleitung

Microchip Technology

Microchip Technology MPLAB ICE Bedienungsanleitung

Microchip Technology

Microchip Technology MCP39F521 Bedienungsanleitung

Microchip Technology

Microchip Technology EVB-LAN7801 Bedienungsanleitung

Microchip Technology

Microchip Technology dsPICDEM MCHV-3 Bedienungsanleitung

Microchip Technology

Microchip Technology PAC1934 Bedienungsanleitung

Microchip Technology

Microchip Technology ATmega4809 Xplained Pro Bedienungsanleitung

Microchip Technology

Microchip Technology PIC32MK Bedienungsanleitung

Microchip Technology

Microchip Technology MCP73830L Bedienungsanleitung

Microchip Technology

Microchip Technology SAM D21 Bedienungsanleitung

Microchip Technology

Microchip Technology ATtiny104 Xplained Nano Bedienungsanleitung

Microchip Technology

Microchip Technology dsPICDEM MCSM Bedienungsanleitung

Microchip Technology

Microchip Technology Hello FPGA Bedienungsanleitung

Microchip Technology

Microchip Technology TA100 Bedienungsanleitung

Microchip Technology

Microchip Technology PIC18F47K42 Curiosity Nano Installationshandbuch

Microchip Technology

Microchip Technology EVB8740 Bedienungsanleitung

Microchip Technology

Microchip Technology MCP1642B Bedienungsanleitung

Microchip Technology

Microchip Technology BM83 EVB Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung