Microchip Technology PICDEM Bedienungsanleitung

PICDEM™ Mechatronics Demo Board

Quick Start Guide

The PICDEM Mechatronics Demo Board is programmed at the factory with a demonstration program. The board must

be conﬁgured as described in this chapter in order to use the demonstration program. Once the board is conﬁgured

and powered up, the speed of the Brushed DC (BDC) motor on the board may be varied using the potentiometer

(POT1). The 8-bit hexadecimal interpretation of the position of POT1 is displayed on the LCD.

Board Setup

Using the provided wire jumpers, screwdriver and shunts (2-pin black hard plastic jumpers), conﬁgure the

board as shown in the Quick Board Setup Schematic.

1. Attach the leads of the brushed DC motor to Drive 1 and Drive 2 using the screwdriver.

2. Connect POT1 (on J4) to C1- (on J13) using a wire jumper.

3. Connect P1 (on J1) to RD7 (on J10) using a wire jumper.

4. Connect N2 (on J1) to RD2/CCP2 (on J10) using a wire jumper.

5. Connect +5 VDC to the center pin on JP8 using a shunt.

Board Power-Up

Supply power to the board in one of the following ways:

• Connect a 9-12 VDC (0.75 amp minimum) supply using J9 (see note below)

• Connect a 9-12 VDC (0.75 amp minimum) supply to the P21 and P20 screw terminals.

• Connect a 9 VDC battery to the battery connector.

• Connect a 5 VDC (1.2 amp minimum) supply to TP2 and TP3.

Demonstration Program

Press CLR FAULT (SW5), which is near the bottom right corner of the board. Turn POT1 clockwise to

increase the speed of the motor. Note that the number displayed on the LCD increases as you turn the

potentiometer clockwise.

Try experimenting with the other sensors on the board:

• Move the jumper wire on POT1 (J4) to Light (J4). Vary the intensity of light shining on the light sensor

located near the top left corner of the board. Notice what happens to the motor.

• Move the same jumper wire to TEMP (J4). Blow on the temperature sensor located on the top left corner

of the board. Note what happens to the number displayed on the LCD.

• Move the jumper wire back to POT1. Move the jumper wire from N2 (J1) to D0 (J14). Watch what

happens to the intensity of LED D0 as you turn the potentiometer.

Microchip Technology Inc. •2355 W. Chandler Blvd. •Chandler, AZ 85224-6199 USA •(480) 792-7200 •FAX (480) 792-7277

The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. In-Circuit Serial

Programming, ICSP and PICDEM are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. All other trademarks mentioned herein are property of

DS51562B *DS51562B*

Quick Board Setup Schematic

Inhaltsverzeichnis

Andere Microchip Technology Hauptplatine Handbücher

Microchip Technology

Microchip Technology ATmega4809 Xplained Pro Bedienungsanleitung

Microchip Technology

Microchip Technology MCP212X Bedienungsanleitung

Microchip Technology

Microchip Technology PAC1710 Bedienungsanleitung

Microchip Technology

Microchip Technology BM78 Bedienungsanleitung

Microchip Technology

Microchip Technology HV2903 Bedienungsanleitung

Microchip Technology

Microchip Technology EVB-LAN9252-PICtail Bedienungsanleitung

Microchip Technology

Microchip Technology EVB-LAN9254-DIGIO Bedienungsanleitung

Microchip Technology

Microchip Technology BM70 PICtail Bedienungsanleitung

Microchip Technology

Microchip Technology MCP1632 Bedienungsanleitung

Microchip Technology

Microchip Technology MCP4725 SOT-23-6 Bedienungsanleitung

Microchip Technology

Microchip Technology PIC18F47K42 Curiosity Nano Installationshandbuch

Microchip Technology

Microchip Technology MCP7386X Bedienungsanleitung

Microchip Technology

Microchip Technology HV9805 Bedienungsanleitung

Microchip Technology

Microchip Technology MPLAB ICE Bedienungsanleitung

Microchip Technology

Microchip Technology UCS81003 Bedienungsanleitung

Microchip Technology

Microchip Technology SAMC21N Xplained Pro Bedienungsanleitung

Microchip Technology

Microchip Technology DM160223 Bedienungsanleitung

Microchip Technology

Microchip Technology ATECC608A Bedienungsanleitung

Microchip Technology

Microchip Technology SAM D21 Bedienungsanleitung

Microchip Technology

Microchip Technology dsPICDEM 1.1 Bedienungsanleitung

Microchip Technology

Microchip Technology HV7351 Bedienungsanleitung

Microchip Technology

Microchip Technology SAMA7G54-EK Bedienungsanleitung

Microchip Technology

Microchip Technology SOT23-6 Bedienungsanleitung

Microchip Technology

Microchip Technology EVB-LAN9370 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung