Microlife W3 Comfort Bedienungsanleitung

IB BP W3 ComfortEN 0220

Europe / Middle-East / Africa

Microlife AG

Espenstrasse 139

9443 Widnau, Switzerland

Tel. +41 71 727 7000

Fax. +41 71 727 7011

Email: [email protected]

www.microlife.com

Asia

Microlife Corporation

9F, 431, RuiGuang Road, NeiHu

Taipei 11492, Taiwan, R.O.C.

Tel. +886 2 8797 1288

Fax +886 2 8797 1283

Email: [email protected]

www.microlife.com

North / Central / South America

Microlife USA, Inc.

1617 Gulf to Bay Blvd

2nd Floor, Suite A

Clearwater, FL 33755, USA

Tel. +1 727 442 5353

Fax +1 727 442 5377

Email: [email protected]

www.microlife.com

 C

C









Microlife BP W3 Comfort

AO-A

AO-B

AO-C

BP W3 ComfortGuarantee Card

Name of Purchaser / Nom de l'acheteur / Nome del rivenditore /

Name des Käufers / Alıcının adı / Nombre del comprador / Nome do

comprador / Naam koper / Ονοματεπώνυμο αγοραστή /

Serial Number / Numéro de série / Numero di serie / Serien-Nr. /

Seri numarası / Número de serie / Número de série / Serienummer /

Αριθμός σειράς /

Date of Purchase / Date d'achat / Data d’acquisto / Kaufdatum / Satın

alma tarihi / Fecha de compra / Data da compra / Datum van aankoop

/ Ημερομηνία αγοράς /

Specialist Dealer / Revendeur / Categoria riven-ditore / Fachhändler

/ Uzman satıcı / Distribuidor especializado / Revendedor autorizado /

Specialist Dealer / Εξειδικευμένος αντιπρόσωποςa /

ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

(ﻲﻔﻠﺨﻟا ءﺎﻄﻐﻟا ﺮﻈﻧا)ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

:يﺮﺘﺸﻤﻟا ﻢﺳا

:ﻞﻳدﻮﻤﻟا

:ﻞﺴﻠﺴﺘﻟا ﻢﻗر

:ءاﺮﺸﻟا ﺦﻳرﺎﺗ

:ﺺﺘﺨﻤﻟا ﺮﺟﺎﺘﻟا

ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

(ﻲﻔﻠﺨﻟا ءﺎﻄﻐﻟا ﺮﻈﻧا)ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

:يﺮﺘﺸﻤﻟا ﻢﺳا

:ﻞﻳدﻮﻤﻟا

:ﻞﺴﻠﺴﺘﻟا ﻢﻗر

:ءاﺮﺸﻟا ﺦﻳرﺎﺗ

:ﺺﺘﺨﻤﻟا ﺮﺟﺎﺘﻟا

ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

(ﻲﻔﻠﺨﻟا ءﺎﻄﻐﻟا ﺮﻈﻧا)ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

:يﺮﺘﺸﻤﻟا ﻢﺳا

:ﻞﻳدﻮﻤﻟا

:ﻞﺴﻠﺴﺘﻟا ﻢﻗر

:ءاﺮﺸﻟا ﺦﻳرﺎﺗ

:ﺺﺘﺨﻤﻟا ﺮﺟﺎﺘﻟا

ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

(ﻲﻔﻠﺨﻟا ءﺎﻄﻐﻟا ﺮﻈﻧا)ﺔﻟﺎﻔﻜﻟا ﺔﻗﺎﻄﺑ

:يﺮﺘﺸﻤﻟا ﻢﺳا

:ﻞﻳدﻮﻤﻟا

:ﻞﺴﻠﺴﺘﻟا ﻢﻗر

:ءاﺮﺸﻟا ﺦﻳرﺎﺗ

:ﺺﺘﺨﻤﻟا ﺮﺟﺎﺘﻟا

1BP W3 Comfort EN

Display

Microlife BP W3 Comfort EN

1ON/OFF button

2Display

3M-button (memory)

4Time Button

5Battery Compartment

6Cuff

7Systolic Value

8Diastolic Value

9Pulse Rate

AT Date/Time

AK Stored Value

AL Traffic Light Indicator

AM Pulse Arrhythmia Indicator (PAD)

AN Cuff Signal Indicator «ERR 1»

AO Cuff Fit Check

-A: Suboptimal Cuff Fit

-B: Arm Movement Indicator «ERR 2»

-C: Cuff Pressure Check «ERR 3»

AP Pulse Indicator

AQ Battery Display

Keep dry

Intended use:

This oscillometric blood pressure monitor is intended for measuring

non-invasive blood pressure in people aged 12 years or older.

Dear Customer,

This device was developed in collaboration with physicians and clinical tests

carried out prove its measurement accuracy to be of a very high standard.*

If you have any questions, problems or want to order spare parts please

contact your local Microlife-Customer Service. Your dealer or pharmacy

will be able to give you the address of the Microlife dealer in your country.

Alternatively, visit the internet at www.microlife.com where you will find a

wealth of invaluable information on our products.

Stay healthy – Microlife AG!

Follow Instructions for Use. This document provides

important product operation and safety information regarding

this Blood Pressure Monitor. Please read this document

thoroughly before using the device and keep for future

reference.

Type BF applied part

* This device is tested according to the

ESH

protocol and

ISO81060-2:2013

Table of Contents

1. Using the Device for the First Time

• Inserting the batteries

• Setting the date and time

2. Checklist for Taking a Reliable Measurement

3. Taking a Blood Pressure Measurement

• How not to store a reading

• How do I evaluate my blood pressure?

• Appearance of the Pulse Arrhythmia (PAD)

F How not to store a reading

F How do I evaluate my blood pressure?

F Appearance of the Pulse Arrhythmia (PAD)

4. Data Memory

• Viewing the stored values

• Memory full

• Clearing all values

5. Battery Indicator and Battery change

• Low battery

• Flat battery – replacement

• Which batteries and which procedure?

• Using rechargeable batteries

6. Error Messages

7. Safety, Care, Accuracy Test and Disposal

• Safety and protection

•Devicecare

• Cleaning the cuff

• Accuracy test

•Disposal

Guarantee

Technical Specifications

1. Using the Device for the First Time

Inserting the batteries

After you have unpacked your device, first insert the batteries. The

battery compartment

is on the bottom of the device. Insert the

batteries (

x 1.5 V, size

AAA

), thereby observing the indicated polarity.

Setting the date and time

1. After the new batteries are fitted, the year number flashes in the

display. You can set the year by pressing the M-button 3. To

confirm and then set the month, press the time button 4.

2. Press the M-button to set the month. Press the time button to

confirm and then set the day.

3BP W3 Comfort EN

3. Follow the instructions above to set the day, hour and minutes.

4. Once you have set the minutes and pressed the time button, the

date and time are set and the time is displayed.

5. If you want to change the date and time, press and hold the time

button down for approx. 3 seconds until the year number starts to

flash. Now you can enter the new values as described above.

2. Checklist for Taking a Reliable Measurement

Avoid activity, eating or smoking immediately before the measurement.

2. Sit down on a back-supported chair and relax for 5 minutes. Keep

the feet flat on the floor and do not cross your legs.

3. Always measure in a sitting position and on the same wrist. Use

the wrist which usually shows higher blood pressure values.

4. Remove any items of clothing and your watch, for example, so

that your wrist is free.

5. Always ensure that the cuff is positioned correctly, as shown in the

pictures illustrated on the short instruction card.

6. Fit the cuff comfortably but not too tight. The cuff will cover a wrist

circumference of 13.5 - 23 cm (5.25 - 9.05 inches).

7. Support your arm in a relaxed position and ensure that the device

is at the same height as your heart.

3. Taking a Blood Pressure Measurement

1. Press the ON/OFF button 1to start the measurement.

2. The cuff fit check AO on the display indicates that the cuff is

perfectly placed. If the icon AO-A appears, the cuff is fitted subop-

timally, but it is still ok to measure.

3. The cuff will now pump up automatically. Relax, do not move and

do not tense your arm muscles until the measurement result is

displayed. Breathe normally and do not talk.

4. The measurement is performed during the inflation. The inflation

speed may vary, this is a normal occurence.

5. During the measurement, the pulse indicator

flashes in the display.

6. The result, comprising the systolic 7and the diastolic 8blood

pressure and the pulse rate 9is displayed. Note also the expla-

nations on further display symbols in this booklet.

7. Remove and switch off the monitor and enter the result in the

enclosed blood pressure pass. (The monitor does switch off auto-

matically after approx. 1 min.).

You can stop the measurement at any time by pressing the

ON/OFF button (e.g. if you feel uneasy or an unpleasant pres-

sure sensation).

How not to store a reading

As soon as the reading is displayed press and hold the ON/OFF

button 1until «M» AK is flashing. Confirm to delete the reading by

pressing the time button AK.

«CL» is displayed when the reading is deleted from the

memory successfully.

How do I evaluate my blood pressure?

The triangle on the left-hand edge of the display

points at the range

within which the measured blood pressure value lies. The value is either

within the optimum (white), elevated (hatched gray) or high (black)

range. The classification corresponds to the following ranges defined by

international guidelines (ESH, ESC, JSH). Data in mmHg.

The higher value is the one that determines the evaluation. Example:

a blood pressure value of 140/80 mmHg or a value of 130/90 mmHg

indicates «blood pressure too high».

Appearance of the Pulse Arrhythmia (PAD)

This symbol AM indicates that certain pulse irregularities were

detected during the measurement. In this case, the result may

deviate from your normal blood pressure – repeat the measurement.

In most cases, this is no cause for concern. However, if the symbol

appears on a regular basis (e.g. several times a week with measure-

ments taken daily) we advise you to tell your doctor. Please show

your doctor the following explanation:

4. Data Memory

This device automatically stores the last 30 measurement values.

Viewing the stored values

Press the M-button 3briefly, when the device is switched off. The

display first shows «M» AK and «A», which stands for the average of

all stored values.

Pressing the M-button again displays the previous value. Pressing the M-

button repeatedly enables you to move from one stored value to another.

Blood pressure readings with suboptimal cuff fit AO-A are not

considered in the average value.

Range Systolic Diastolic Recommendation

1. blood pressure

too high

≥135 ≥85 Seek medical

advice

2. blood pressure

elevated

130 - 134 80 - 84 Self-check

3. blood pressure

normal

<130 <80 Self-check

Information for the doctor on frequent appearance of the

Arrhythmia indicator

This device is an oscillometric blood pressure monitor that also

analyses pulse irregularity during measurement. The device is

clinically tested.

The arrhythmia symbol is displayed after the measurement, if

pulse irregularities occur during measurement. If the symbol

appears more frequently (e.g. several times per week on

measurements performed daily) we recommend the patient to

seek medical advice.

This device does not replace a cardiac examination, but serves

to detect pulse irregularities at an early stage.

5BP W3 Comfort EN

Memory full



Pay attention that the maximum memory capacity of

memo-

ries is not exceeded.

When the

memory is full, the oldest

value is automatically overwritten with the

31st

value.

Values should be evaluated by a doctor before the memory

capacity is reached – otherwise data will be lost.

Clearing all values

If you are sure that you want to permanently remove all stored

values, hold down the M-button (the device must have been switched

off beforehand) until «CL ALL» appears and then release the button.

To permanently clear the memory, press the time button while «CL

ALL» is flashing. Individual values cannot be cleared.



Cancel deletion:

press ON/OFF button

while «

CL ALL

» is

flashing.

5. Battery Indicator and Battery change

Low battery

When the batteries are approximately ¾ empty the battery symbol AQ

will flash as soon as the device is switched on (partly filled battery

displayed). Although the device will continue to measure reliably, you

should obtain replacement batteries.

Flat battery – replacement

When the batteries are flat, the battery symbol AQ will flash as soon

as the device is switched on (flat battery displayed). You cannot take

any further measurements and must replace the batteries.

1. Open the battery compartment 5by pulling off the cap.

2. Replace the batteries – ensure correct polarity as shown by the

symbols in the compartment.

3. To set date and time, follow the procedure described in «Section 1.».

The memory retains all values although date and time must be

reset – the year number therefore flashes automatically after

the batteries are replaced.

Which batteries and which procedure?

Use 2 new, long-life 1.5 V, size AAA alkaline batteries.

Do not use batteries beyond their date of expiry.

Remove batteries if the device is not going to be used for a

prolonged period.

Using rechargeable batteries

You can also operate this device using rechargeable batteries.

Only use «NiMH» type reusable batteries.

Batteries must be removed and recharged when the flat

battery symbol appears. They should not remain inside the

device as they may become damaged (total discharge as a

result of low use of the device, even when switched off).

Always remove the rechargeable batteries if you do not intend

to use the device for a week or more.

Batteries cannot be charged in the blood pressure monitor.

Recharge batteries in an external charger and observe the

information regarding charging, care and durability.

6. Error Messages

If an error occurs during the measurement, the measurement is inter-

rupted and an error message, e.g. «ERR 3», is displayed.

* Please immediately consult your doctor, if this or any other problem

occurs repeatedly.

If you think the results are unusual, please read through the

information in «Section 1.» carefully.

7. Safety, Care, Accuracy Test and Disposal

Safety and protection

•Follow instructions for use. This document provides important

product operation and safety information regarding this device.

Please read this document thoroughly before using the device and

keep for future reference.

Error Description Potential cause and remedy

ERR 1

Signal too

weak

The pulse signals on the cuff are too weak. Re-

position the cuff and repeat the measurement.*

ERR 2

Error signal During the measurement, error signals were

detected by the cuff, caused for instance by

movement or muscle tension. Repeat the

measurement, keeping your arm still.

ERR 3

No pressure

in the cuff

An adequate pressure cannot be generated in

the cuff. A leak may have occurred. Check that

the cuff is correctly connected and is not too

loose. Replace the batteries if necessary.

Repeat the measurement.

ERR 5

» Abnormal

result

The measuring signals are inaccurate and no

result can therefore be displayed. Read through

the checklist for performing reliable measure-

ments and then repeat the measurement.*

» Pulse or cuff

pressure too

high

The pressure in the cuff is too high (over

299 mmHg) OR the pulse is too high (over

200 beats per minute). Relax for 5 minutes

and repeat the measurement.*

» Pulse too

low

The pulse is too low (less than 40 beats per

minute). Repeat the measurement.*

Error Description Potential cause and remedy

7BP W3 Comfort EN

•This device may only be used for the purposes described in these

instructions. The manufacturer cannot be held liable for damage

caused by incorrect application.

•This device comprises sensitive components and must be treated

with caution. Observe the storage and operating conditions

described in the «Technical Specifications» section.

•Protect it from:

- water and moisture

- extreme temperatures

- impact and dropping

- contamination and dust

- direct sunlight

- heat and cold

•The cuffs are sensitive and must be handled with care.

•Only pump up the cuff once fitted.

•Do not use this device close to strong electromagnetic fields such

as mobile telephones or radio installations. Keep a minimum

distance of 3.3 m from such devices when using this device.

•Do not use this device if you think it is damaged or notice anything

unusual.

•Never open this device.

•If the device is not going to be used for a prolonged period the

batteries should be removed.

•Read the additional safety information provided within the indi-

vidual sections of this instruction manual.

•The measurement results given by this device is not a diagnosis.

It is not replacing the need for the consultation of a physician,

especially if not matching the patient’s symptoms. Do not rely on

the measurement result only, always consider other potentially

occurring symptoms and the patient’s feedback. Calling a doctor

or an ambulance is advised if needed.

Ensure that children do not use this device unsupervised;

some parts are small enough to be swallowed. Be aware of

the risk of strangulation in case this device is supplied with

cables or tubes.

Device care

Clean the device only with a soft, dry cloth.

Cleaning the cuff

Carefully remove any marks on the cuff with a damp cloth and mild

detergent.

Accuracy test

We recommend this device is tested for accuracy every 2 years or

after mechanical impact (e.g. being dropped). Please contact your

local Microlife-Service to arrange the test (see foreword).

Disposal

Batteries and electronic devices must be disposed of in accor-

dance with the locally applicable regulations, not with

domestic waste.

8. Guarantee

This device is covered by a

year guarantee

from the date of

purchase. The guarantee is valid only on presentation of the guarantee

card completed by the dealer (see back) confirming date of purchase

or the receipt.

•

Batteries, cuff and parts that become worn with use are not included.

•Opening or altering the device invalidates the guarantee.

•The guarantee does not cover damage caused by improper

handling, discharged batteries, accidents or non-compliance with

the operating instructions.

Please contact your local Microlife-Service (see foreword).

9. Technical Specifications

Operating conditions: 10 - 40 °C / 50 - 104 °F

15 - 95 % relative maximum humidity

Storage conditions: -20 - +55 °C / -4 - +131 °F

15 - 95 % relative maximum humidity

Weight: 112

g (including batteries)

Dimensions: 81 x 65 x 21

Cuff size: 13.5 - 23 cm (5.25 - 9.05 inches)

Measuring procedure:

oscillometric, corresponding to Korotkoff

method: Phase I systolic, Phase V diastolic

Measurement range: 20 - 280 mmHg – blood pressure

40 - 199 beats per minute – pulse

Cuff pressure display

range:

Resolution:

Static accuracy:

Pulse accuracy:

Voltage source:

Battery lifetime:

IP Class:

Reference to

standards:

0 - 299 mmHg

1 mmHg

pressure within ± 3 mmHg

± 5% of the readout value

2 x 1.5 V alkaline batteries; size AAA

approx. 320 measurements

(using new batteries)

IP20: Protected against solid foreign

particles with a diameter of more than

12.5 mm, no protection against water .

EN 1060-1 /-3 /-4; IEC 60601-1;

IEC 60601-1-2 (EMC); IEC 60601-1-11

Expected service life: Device: 5 years or 10000 measurements

Cuff: 2 years or 10000 measurements

This device complies with the requirements of the Medical Device

Directive 93/42/EEC.

Technical alterations reserved.

Inhaltsverzeichnis

Andere Microlife Blutdruckmessgerät Handbücher

Microlife

Microlife BP B2 Basic Bedienungsanleitung

Microlife

Microlife BP W3 Comfort Bedienungsanleitung

Microlife

Microlife BPB3 Comfort PC Bedienungsanleitung

Microlife

Microlife BP A3L Comfort Bedienungsanleitung

Microlife

Microlife BP A1 Easy Bedienungsanleitung

Microlife

Microlife BP3AQ1-1 Bedienungsanleitung

Microlife

Microlife BPB3 AFIB Bedienungsanleitung

Microlife

Microlife BPB1 Classic Bedienungsanleitung

Microlife

Microlife BP A3 PLUS Bedienungsanleitung

Microlife

Microlife BP3GT1-6B Bedienungsanleitung

Microlife

Microlife BP A6 BT Bedienungsanleitung

Microlife

Microlife BP A1 Easy Bedienungsanleitung

Microlife

Microlife BP3GX1-5A Bedienungsanleitung

Microlife

Microlife WatchBP Office Central Bedienungsanleitung

Microlife

Microlife Aponorm Mobil Bedienungsanleitung

Microlife

Microlife BP A90 Bedienungsanleitung

Microlife

Microlife BP W2 Slim Bedienungsanleitung

Microlife

Microlife BP A150 AFIB Bedienungsanleitung

Microlife

Microlife BP N2 Easy Bedienungsanleitung

Microlife

Microlife WatchBP O3 Bedienungsanleitung

Microlife

Microlife BP A3L PC Bedienungsanleitung

Microlife

Microlife BP B2 Basic Bedienungsanleitung

Microlife

Microlife BP AG1-20 Bedienungsanleitung

Microlife

Microlife BP A1 Easy Bedienungsanleitung

Beliebte Blutdruckmessgerät Handbücher anderer Marken

Little Doctor

Little Doctor LD7 Bedienungsanleitung

Omron

Omron M6W Handbuch

Mx Onda

Mx Onda MX-CP2395 Bedienungsanleitung

Braun

Braun VitalScan 1 Bedienungsanleitung

Little Doctor

Little Doctor LD-91 Bedienungsanleitung

Sanitas

Sanitas SBM 09 Bedienungsanleitung

A&D

A&D LifeSource UB-328 Bedienungsanleitung

König Electronic

König Electronic HC-BLDPRESS200 Bedienerhandbuch

Leicke

Leicke Sharon Bedienungsanleitung

Omron

Omron M6 Comfort Bedienungsanleitung

3B SCIENTIFIC

3B SCIENTIFIC U11395 Bedienungsanleitung

Soehnle

Soehnle SYSTO MONITOR 100 Bedienungsanleitung

Nasco Healthcare

Nasco Healthcare Simulaids Life/form LF01095U Referenzhandbuch

HoMedics

HoMedics MiBody 360 Bedienungsanleitung

ForaCare

ForaCare FORA P30 Plus Bedienungsanleitung

JOYTECH

JOYTECH DBP-6296B Bedienungsanleitung

Omron

Omron Silver BP5250 Bedienungsanleitung

visomat

visomat double comfort Bedienungsanleitung