MicroNet SP616DB Bedienungsanleitung

User’s Manual

EtherFast 10/100M Smart Switch

Model No.: SP616DB / SP624DB

http://www.micronet.info

Package Contents

Verify your package contains the following items:

zSP616DB/SP624DB 10/100 Mbps Smart Switch

zUser’s Manual

zPower Cord

zRack Ears with Screws and Rubber Foots

Features

Micronet SP616DB/SP624DB has the following key features:

zProvide 16 (SP616DB) or 24 (SP624DB) RJ-45 ports of 10/100 Mbps, auto negotiation

zProvide one expansion slot for optional fiber optic module

zProvide one web-based console port

zProvide 2K (SP616DB)/10K (SP624DB) MAC address and 2M (SP616DB)/1.5M (SP624DB)

buffer memory

zProvide 16 (SP616DB) or 24 (SP624DB) port-based VLAN groups to segment network

zProvide 2 trunking groups to aggregate bandwidth

zProvide auto-uplink function, no more cross-over cable

zSupport store-and-forward mechanism

zSupport non-blocking wire speed forwarding rate

zSuitable for rack-mount installation

Physical Description

Front Panel

Figure 1: Front Panel of SP616DB

Figure 2: Front Panel of SP624DB

POWER

This LED comes on when the switch is properly connected to power and turned on.

TX/FX Push Button

The push button is located at the right side of port 16 (SP616DB) or port 24 (SP624DB).

Release this button to use RJ-45 port 16 (SP616DB) or port 24 (SP624DB), and press this button

to use the 100BASE-FX module.

IP RESET Push Button

Press the front panel IP RESET push button for around five seconds to reset the Switch back to

default IP Address (192.168.1.10).

Port Status

The RJ-45 ports are numbered from 1 to 16 (SP616DB), or from 1 to 24 (SP624DB).

LEDs

Label Status Indication

On Power is feeding in.

Power is switched off.

POWER

Off

Improper connection.

On A valid network connection. LNK stands for LINK.LNK

Off No connection.

Flashing Transmitting or receiving data. ACT stands for

ACTIVITY.

CONSOLE

ACT

Off Neither connection nor activity.

On A valid network connection. LNK stands for LINK.

Flashing Transmitting or receiving data. ACT stands for

ACTIVITY.

LNK/ACT

Off Neither connection nor activity.

On A valid 100Mbps connection.

PORT

SPEED

Off A valid 10Mbps connection.

On A valid network connection. LNK stands for LINK.LNK

Off No connection.

Flashing Transmitting or receiving data. ACT stands for

ACTIVITY.

ACT

Off Neither transmitting nor receiving data.

Table 1: SP616DB/SP624DB LED Indication

Installation

Preparing the Site

Select the site that meets the following requirements:

Characteristic Requirement

Temperature 32 to 104˚F (0 to 40˚C)

Humidity Maximum relative humidity of 90%, non-condensing

Condition At least 1.8 meters (6 feet) to the nearest source of electromagnetic noise

Ventilation Minimum 3 inches (0.25 feet) of clearance around the ventilation openings

Power Outlet Within 1.8 meters (6 feet) to the switch

Table 2: SP616DB / SP624DB Operating Requirements

Settling the Switch

zMounted to 19-inch standard rack

Locate the accessories provided in the product package. Use the rack-mount brackets and

screws to install the switch into any EIA 19” standard rack.

Step 1: Attach the brackets to each side of the chassis.

Step 2: Apply the screws to each side and secure them tightly.

Step 3: Carefully position the switch into the rack.

Step 4: Align the brackets to the side holes on the rack and use rack screws to secure the

chassis with the rack.

Step 5: Proceed to the “Connecting to Power” section.

zDesktop or any flat surface

The switch can sit on desktop or any flat surface with adequate space and ventilation. If you

want to place it onto a shelf, make sure the shelf can withstand the weight of the switch.

Step 1: Simply put the switch on the desired place.

Step 2: Ensure the switch receives good ventilation.

Step 3: Proceed to the “Connecting to Power” section.

Installing the Module (optional)

Consult the following illustrations for installation.

Figure 3: Removal of cover plate Figure 4: Fiber module being installed

Step 1: Make sure the power is switched off. The module is not hot-swappable.

LIt may cause electric shock or any possible damage to the switch if the power is not

switched off.

Step 2: Remove the module from the static-free container.

Step 3: Unscrew the cover plate of the expansion slot.

(The slot for single-port module is located at the right side of the switch.)

Step 4: Remove the plate.

(Keep it for future use in case you decide to remove this module later.)

Step 5: Carefully slide the module into the slot, along the internal plastic guide rails.

Step 6: Once it is fully slid in, snap in the module to make a proper connection.

Step 7: Fasten the module screws then.

Step 8: Finally, turn on the power.

Connecting to Power

Locate the provided AC power cord.

Step 1: Connect the AC power cord to the receptacle at the back of the switch.

Step 2: Attach the plug into a standard AC outlet with a voltage ranging from 100 to 240 VAC.

Step 3: The power LED on the front panel will come on then.

Connecting to Network

Step 1: First, ensure the power of the switch (and end devices) is turned off.

LIt may cause electric shock or any possible harm to you if the power is not switched off.

Step 2: Prepare cable with corresponding connectors for each type of port in use.

Step 3: Connect one end of the cable to the switch and the other end to a desired device.

Step 4: Once the connections between two end-devices are made successfully, turn on the

power.

Now the switch is operational.

Switch Configuration

Setting UP Console Port Connection

SP616DB/SP624DB provides one RJ-45 console port and a web-based interface, allowing users

to configure and manage the switch remotely from web browser.

1. Connect UTP/STP cable to SP616DB/SP624DB’s console port.

Figure 5: Connect directly to PC Figure 6: Connect to PC via another switch

2. In the web browser, specify the default IP address of SP616DB/SP624DB (192.168.1.10).

Default User Name: admin

Default Password: (null)

Figure 7: Switch Configuration Login

Main Menu

Figure 8: Main menu

System Change

The System Change parameters can be displayed by clicking the System Change button in the

left sub-menu.

Figure 9: System Change

zSwitch Name: Type a switch name and replace the current switch name with a new one.

(Please restart your Computer once the Switch Name is replaced and saved under

“Save Configuration “by the new name ).

Note: only “a-z “, “A-Z”, “0-9”, “under line” & “Space” can be acceptable, totally can not

exceed 16 characters.

zPassword: Enter a user-defined password and change the factory default password.

Note: only “a-z “, “A-Z”, “0-9”, “under line” & “Space” can be acceptable, totally can not

exceed 16 characters.

zApply: Click the Apply button and apply the new System settings.

IP Configuration

Figure 10: IP Configuration

zRefresh: Click the Refresh button and refresh back to the last saved IP Configurations.

zIPAddress, Netmask, Default Gateway: You can see and change the IPAddress, Netmask,

and Default Gateway of the Ethernet Switch.

zApply: Click the Apply button and apply the new IP Configurations.

Port

Figure 11: Port

zRefresh: Click the Refresh On or Refresh Off button to or not to refresh back to the last

saved settings of the ports.

Note: it is recommended to change the Refresh On button to Refresh Off while you

change the settings of the ports. The Refresh On will refresh the settings of the ports

shown on the screen around every ten seconds.

zMode: Choose AUTO, 10HD, 10FD, 100HD or 100FD for the ports.

zFlow Control: Choose Enable or Disable to enable or disable the flow control of the ports.

zTransmit / Receive: Choose On or Off to turn on or off transmit / receive of the ports.

zApply: Click the Apply button and apply the new settings of the ports.

VLAN

Figure 12: VLAN

zVLAN: Click and choose the ports to be added into the VLAN groups.

zApply: Click the Apply button and apply the new settings of the VLAN groups.

Note: all Ports have to be selected to one of the VLAN Groups, those Port/Ports were not

selected will be notified by the alarm message which shows “Non-Identify VLAN Group “.

Trunk

SP616DB:

Figure 13: Trunk of SP616DB

zDisable: Click and choose the Disable to disable the Trunk Group 1 or Trunk Group 2.

zTrunk Group 1: Click and choose the Port 1, 2 to be added into the Trunk Group 1.

zTrunk Group 2: Click and choose the Port 9, 10 to be added into the Trunk Group 2.

zApply: Click the Apply button and apply the new settings of the Trunk Groups.

SP624D:

Figure 14: Trunk of SP624DB

zTrunk Group 1: Click and choose any four ports to be added into the Trunk Group 1.

zTrunk Group 2: Click and choose any four ports to be added into the Trunk Group 2.

zApply: Click the Apply button and apply the new settings of the Trunk Groups.

Note: each Trunk Group can not be selected more than four ports, the alarm message will

show “Non-Identify Trunk Group“, if it’s exceeded.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MicroNet Schalten Handbücher

MicroNet

MicroNet SP6824P Bedienungsanleitung

MicroNet

MicroNet SP6008P Bedienungsanleitung

MicroNet

MicroNet SP1678A Bedienungsanleitung

MicroNet

MicroNet SP6510P8 Bedienungsanleitung

MicroNet

MicroNet SP6008P Bedienungsanleitung

MicroNet

MicroNet SP212E Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

MicroNet

MicroNet SP6008P Bedienungsanleitung

MicroNet

MicroNet SP698A Bedienungsanleitung

MicroNet

MicroNet SP616R Bedienungsanleitung

MicroNet

MicroNet SP607FA Bedienungsanleitung

MicroNet

MicroNet SP676C Bedienungsanleitung

MicroNet

MicroNet SP212E Bedienungsanleitung

MicroNet

MicroNet SP508C Bedienungsanleitung

MicroNet

MicroNet SP6108I Bedienungsanleitung

MicroNet

MicroNet SP684C Bedienungsanleitung

MicroNet

MicroNet SP684C Bedienungsanleitung

MicroNet

MicroNet SP6108WS Bedienungsanleitung

MicroNet

MicroNet SP6124A Bedienungsanleitung

MicroNet

MicroNet SP6510P8 Bedienungsanleitung

MicroNet

MicroNet SP6524PWS Bedienungsanleitung

MicroNet

MicroNet SP218D Bedienungsanleitung

MicroNet

MicroNet SP212D Bedienungsanleitung

MicroNet

MicroNet SP6008P Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung