Microscan MS-3 Bedienungsanleitung

P/N 83-210027-04 Rev A1

Quick Start Guide

MS-3 Laser Scanner

This guide is designed to get your scanner up and running

quickly. When connected to a host computer with Windows™

operating system (2000 or above), you can use

ESP

(Easy Setup

Program) to configure and control your

MS-3 Laser Scanner

. In

addition to

ESP

, you can send commands to your scanner by

serial command and by the scanners’s embedded menus.

For a full explanation of the MS-3’s commands and features,

refer to the Help section of

ESP

or contact your Microscan sales

representative for the

MS-3 Laser Scanner User’s Manual,

available in digital and print formats.

2MS-3 Laser Scanner Quick Start Guide

Warranty

For current warranty information, see:

www.microscan.com/warranty

MS-3 Laser Scanner Quick Start Guide 3

Step 1 —Check Required Hardware

Caution: If using your own power supply, be certain that it is wired

correctly and supply voltage is 10 to 28VDC. Incorrect wiring or

voltage can cause software or equipment failures.

If connecting to a host with an IB-131 Interface Box, you will need the

following:

•(1) MS-3 Laser Scanner,

FIS-0003-XXXX

•

(

)

IC-331

Interface Converter

98-000050-01

•(3) IB-131 Interface Box,

99-400005-02

•(4) Host Computer

•(

)

Null Modem Configuration

Cable

, 61-300026-01, DB-25

plug to DB-9 socket, 6ft.

•(6) Power Supply,

97-100004-05 (120V) or

97-100004-06 (240V)

•(7) Object Detector

(optional), 99-4400021-03

Scanner

Network

Host

Hardware Required

4MS-3 Laser Scanner Quick Start Guide

Step 2 —Connect the System

Caution: Be certain all cables are connected BEFORE applying

power. Always power down BEFORE disconnecting cables.

To connect the system, do the following:

1. Connect the scanner

(

) to the “SCANNER”

connector on the IC-

331

interface converter

(2) using the

attached

3-foot custom

cable.1

2. Connect the IC-331

directly to the

“SCANNER” 15 pin

connector on the

IB-131 (3).

3. Connect the Host

Computer (4) to the

IB-131

“HOST” 25-pin

connector via the Null Modem Config. Cable (5).2

4. Connect Power Supply (6) to the IB-131 “POWER” connector.

5. Apply power to the system.

1. Since power supply is included in the single cabling assembly, the scanner cable should not

exceed 3 feet. RS-232 cabling from the IB-131 to the host can be up to 47 feet provided it

does not include power input.

2. If using your own null modem RS-232 host cable, be certain that the host’s TxD connects to

the scanner’s RxD and the scanner’s TxD connects to the host’s RxD.

Hardware Connections

Scanner

Network

Host

MS-3 Laser Scanner Quick Start Guide 5

Step 3 —Install ESP

ESP Software can be found on the Microscan Tools Drive that is

packaged with the MS-3.

1. Follow the prompts to install ESP from the Tools Drive.

2. Click on the ESP icon to run the program.

Note: ESP can also be installed from the Download Center at

www.microscan.com.

Minimum System Requirements

• 233 MHz Pentium processor

• Windows 7 (32-bit or 64-bit), Vista (32-bit or 64-bit), XP, or 2000

operating system

• Internet Explorer 6.0 or higher

• 128 MB RAM or greater

• 80 MB hard drive space

• 800 x 600 minimum 256 color display (1024 x 768 32-bit color

recommended)

Refer to the MS-3 Laser Scanner User’s Manual for detailed information

about using ESP to configure the MS-3.

6MS-3 Laser Scanner Quick Start Guide

Step 4 —Select Scanner Model

When you start the program,

this menu will appear:

1. Select MS-3 Laser

from the menu and

click OK. If you do not

want to make this

selection every time

you load ESP,

uncheck “Show this

window at Startup”.

2. Select the default

name (MS-3 Laser-1,

for example) or type

in a file name of your

choice and click OK.

3. Click Yes when the

connect dialog

appears.

Note: If you need to select another model later, you can find it in App

Mode under Model on the menu bar.

MS-3 Laser Scanner Quick Start Guide 7

Step 5 —Autoconnect

1. In the Connecting... dialog, if your communications port is not

the default COM1, use the dropdown menu to change your

communications port.

2. Click the Start button.

When connected, the scanner’s settings will be loaded into

ESP and the CONNECTED message will appear in a green

box in the status bar at the bottom right of your screen.

If the connection fails, enable a different

Com Port

, check connections,

and try again.

Tip

: If you do not see the

CONNECTED

DISCONNECTED

message

at the bottom of your dialog, try expanding the

ESP

window horizontally.

8MS-3 Laser Scanner Quick Start Guide

Step 6 —Position Symbol and Scanner

Note: Code 39 is the default code type enabled. If you are uncertain

as to your symbology type, enable all codes by selecting the Auto

Discriminate macro in Terminal mode.

1. Set up a symbol at the distance you are using in your application.

2. Avoid bright light or IR light from other sources, including other

scanners.

3. Pitch the symbol or scanner at a minimum of ±15° to avoid

specular reflection (the return of direct, non-diffused light).

Pitch

axis

Bar code

label

Tilt

axis

Skew

axis

Scan line

Scanner

Symbol/Scanner Positioning

MS-3 Laser Scanner Quick Start Guide 9

Step 7 —Test Read Rate

With this test you can learn the percentage of decodes per images

captured by observing the LEDs (20% through 100%) on the top of

the MS-3 which are active during a read rate test. If the results are

not satisfactory, move on to Step 8 — “Calibrate the Scanner”.

By ESP

After connecting to the scanner, ESP will open in Setup Mode.

1. Click the Test button in Setup Mode to begin the

read rate test.

2. Follow the instructions in Setup Mode.

3. To end the read rate test, click the Stop button.

By EZ Button

1. Press and hold the Test

button on the MS-3 until

you hear one beep and

see one LED momentarily

turn amber. This will

signal the beginning of

the read rate routine.1

2. To end the read rate test

press the Test button

and quickly release.

1. This assumes that the default functions of the test button have not been re-programmed.

PWR

40%

60%

80%

20%

100%

11-000063-01

TEST

LASER

MS-3

EZ Button

Read Rate

Read rate

performance

LEDs

10 MS-3 Laser Scanner Quick Start Guide

Step 8 —Calibrate the Scanner

During the calibration routine, the scanner attempts various settings

to determine the optimum decode rate for the given conditions. In this

process it might do the following:

The test will end automatically when the optimum combination of

settings has been achieved.

By ESP

Click the Calibrate button in Setup Mode to

begin the read rate test.

You can observe the progress of the calibration

routine on the Calibration popup.

Note: You can also use the Calibration menu in App Mode.

By EZ button

Press and hold the

Test

button

until you hear two

beeps and

see two performance LEDs

turn amber to indicate that the

calibration is in progress.

The scanner will beep once

at the end of calibration.

• Adjust laser power

• Adjust mirror motor speed

• Adjust AGC gain

• Enable Autodiscrimination

(read several symbol types)

PWR

40%

60%

80%

20%

100%

11-000063-01

TEST

LASER

MS-3

EZ Button

Read rate

performance

LEDs

Calibration

Andere Handbücher für MS-3

Inhaltsverzeichnis

Andere Microscan Scanner Handbücher

Microscan

Microscan MS-710 Bedienungsanleitung

Microscan

Microscan QX-830 Bedienungsanleitung

Microscan

Microscan MS-615 Bedienungsanleitung

Microscan

Microscan HS-1 Bedienungsanleitung

Microscan

Microscan MS-3 Bedienungsanleitung

Microscan

Microscan N2210WZ Bedienungsanleitung

Microscan

Microscan HS-1 Bedienungsanleitung

Microscan

Microscan MS-2 Bedienungsanleitung

Microscan

Microscan HS-1 Bedienungsanleitung

Microscan

Microscan Visionscape FrontRunner Bedienungsanleitung

Microscan

Microscan MS-610 Bedienungsanleitung

Microscan

Microscan MS-890 Bedienungsanleitung

Microscan

Microscan MS-9 Bedienungsanleitung

Microscan

Microscan MS-7100 Bedienungsanleitung

Microscan

Microscan MS-850 Bedienungsanleitung

Microscan

Microscan QX-870 Bedienungsanleitung

Microscan

Microscan QX-830 Bedienungsanleitung

Microscan

Microscan MS-3 Produkthandbuch

Microscan

Microscan QX-870 Bedienungsanleitung

Microscan

Microscan MS-810 Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung