Microtek C593 Bedienungsanleitung

C593 15” LCD MONITOR

USER’S MANUAL

All manuals and user guides at all-guides.com

all-guides.com

Installing The Monitor

Follow these steps to install the monitor,

1. Before you connect the cables,make sure that the monitor and the

system unit power switches are OFF.

2. Please follow the following drawing to remove the plastic back over in

order to connect the signal cable and power cable.

3. Plug one end of the 15pin signal cable to the monitor and the other

end to the video signal connector at the rear of the system. Tighten

the two screws on the cable connector on both ends, otherwise the

screen will be abnormal and LED light is yellow color, not the normal

green color.

4. Connect the power to the monitor through the AC/DC adapter.

5. Connect the power cord on the AC outlet, see the below.

All manuals and user guides at all-guides.com

iii

Content

Operating Instructions ............................................................................iv

Safety Precautions ...................................................................................v

Care and Maintenance ...........................................................................vi

Control Functions .....................................................................................1

Adjustment Procedure .............................................................................2

Auto Adjustment..............................................................................2

RGB Adjustment ................................................................................3

Contrast Value Adjustment ........................................................3

Color Balance .............................................................................3

Geometry Adjustment ......................................................................4

Vertical & Horizontal Position Adjustment................................4

Viewer Screen Size Adjustment ...............................................4

Phase Adjustmentt.....................................................................4

Multilanguage Support .....................................................................5

DOS Txt/GFX. ....................................................................................5

Color Temperature ............................................................................5

Brightness Adjustment .....................................................................5

Understanding the Display Resolution Setting ...............................5

General Specifications .............................................................................6

General Performance ..............................................................................7

All manuals and user guides at all-guides.com

Operating Instru tions

Thank you for purchasing this high resolution multi scan color monitor. Please read

this guide thoroughly before installation.

FCC RADIO FREQUENCY INTERFERENCE STATEMENT WARNING:

(FOR FCC CERTIFIED MODELS)

This monitor has been tested and found compliant with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

proper protection against harmful interference to a residential installation. This

monitor generates, uses, and can radiate radio frequency energy. Harmful

interference to radio communication may result if it is not properly installed and

used. However, there is no guarantee that interference will not occur in a particular

installation. If this monitor does cause serious interference to radio or television

reception, resetting the monitor may resolve the problem. Moreover, users are

encouraged to correct interference by doing one or more of the following:

• Reorient or relocate the receiving antenna.

• Move the monitor and the receiver further away from each other.

• Connect the monitor into an outlet on a circuit different from that to which

the receiver is connected.

• Consult your local dealer or a qualified technician.

FCC Warning:

To assure a continued FCC compliance, a user must use a grounded power supply

cord and the provided shielded video interface cable with bonded ferrite cores. Also,

any unauthorized changes or modifications to this monitor will void the user’s

authority to operate this device.

Note: If necessary, shielded interface cables and the A.C. power cord must be used

to meet the emission level limits.

EMI Certifi ation

The Class B digital apparatus meets all requirements of the Canadian Interference

Causing Equipment Regulation. Cet appareil numerique de class B respecte toutes

les exigences du Reglement sur Ic materiel brouilleur du Canada.

All manuals and user guides at all-guides.com

Safety Pre autions

This monitor is manufactured and tested on the ground principle that a user’s safety

comes first. However, improper use or installation may not only damage the

monitor but endanger the user as well. As a safety precaution, go over the following

WARNINGS carefully before installation, and keep this guide handy.

Warnings:

• This monitor should be operated only at the correct power sources

indicated on the label at the rear end of the monitor. If you are unsure of the

power supply in your residence, consult your local dealer or Power

Company.

• Do not try to repair the monitor yourself, as it contains no user serviceable

parts. The monitor should only be repaired by a qualified technician.

• Do not remove the monitor cabinet. There are high voltage parts inside that

may cause electric shock to human bodies, even when the power cord is

disconnected.

• Stop using the monitor if the cabinet is damaged. Have it checked by a

service technician.

• Put your monitor only in a clean, dry environment. Unplug the monitor

immediately if it gets wet, and consult your service technician.

• Always unplug the monitor before cleaning it. Clean the cabinet with a

clean, dry cloth. Apply non ammonia based cleaner onto the cloth, not

directly onto the glass screen.

• Keep the monitor away from magnetic objects, motors, TV sets, and

transformers.

• Do not place heavy objects on the cable or power cord.

• For PLUG CABLE EQUIPMENT, the socket outlet should be installed near the

equipment and should be easily accessible.

All manuals and user guides at all-guides.com

Care and Maintenan e

Care

• Avoid exposing your monitor directly to sunlight or other heat sources.

Place your monitor away from the sun to reduce glare.

• Put your monitor in a well ventilated area. Do not place anything heavy on

top of your monitor.

• Make certain that your monitor is installed in a clean and moisture free

area.

• Keep your monitor away from magnets, motors, transformers, speakers,

and TV sets.

Safety Tips

• If smoke, abnormal noise or odor comes out of your monitor, switch off the

power immediately and call your service center.

• Never remove the rear cover of your monitor cabinet. The display unit

inside contains high voltage parts and may cause electric shock to human

bodies.

• Never try to repair the monitor yourself. Always call your service center or

a qualified technician to fix it.

Note: This user’s manual contains graphics and information that is for reference

purposes only and is subject to change without notice.

All manuals and user guides at all-guides.com

all-guides.com

Control Fun tions

The Monitor control functions are located on the lower center portion of

the front panel. These are shown in the figure below and described in the

following paragraphs.

1. : Power swit h

Use the power switch to turn power ON or OFF. We recommend

turning your system power on first, then the LCD monitor

2. - & + : De rement & In rement

These two keys are used to decrease or increase the values of each

selected item.

3. Sele tion: Down key

This key is used to select the wanted adjustment item. It always move

down to the next item.

4. Menu

Press the Menu key to activate the on-screen display. This is a toggle

key, so press twice to turn off the on-screen display. After 30 seconds

of idle time, the OSD screen will automatically turn off.

5. Auto adjustment

Press this key to get better visual performance.

All manuals and user guides at all-guides.com

1024X768 75Hz/60KHz

AUTO ADJUSTMENT

LANGUAGE MENU

DOS/GFX OFF

USER

100

VERSION XGAD9B11 5100

Adjustment Pro edure

1. Press the Menu key to activate the OSD screen. The screen below will

appear.

Note: Perform the procedure above whenever you need to change a

setting. For the succeeding sections, this step will not be included,

and users will be presumed to have performed the procedure.

OSD SCREEN

2. Use the selection key to move to the desired item.

3. Use the - & + key to carry out the desired function or to go to the

second menu item and perform further changes.

Auto-Adjustment

We strongly recommend that you use this item to get the optimized visual

quality. Use the selection key to select auto-adjustment, then press - or +

to get the optimized quality.

All manuals and user guides at all-guides.com

RGB Adjustment

Use the selection key to select the icon, then press - or +. The screen

belowwillappear.

1024X768 75 Hz/60 KHz

Auto Balance

CONTRAST

RED 20

GREEN 18

BLUE 19

BALANCE

RED 49

GREEN 50

BLUE 26

VERSION XGAD9B11 5100

Contrast Value Adjustment

Use the selection key to select the CONTRAST field, then press - & + to

get the best contrast optimization. You can adjust R,G,B simultaneously or

adjust each Red, Green, and Blue channel separately. You can also use this

field to change purity of the RGB levels.

Color Balan e

Use the selection key to select the COLOR BALANCE field, then press - &

+ to get the best color balance effect or to separately set the RGB color

values. You can also use this field to change intensity of the RGB levels.

Theeasiestwayto adjustthecontrastand colorbalancesettingis touse

auto-balance.

All manuals and user guides at all-guides.com

Geometry Adjustment

Use the selection key to select the icon, then press - & +. The screen

belowwillappear.

1024X768 75 Hz/60 KHz

1344

PHASE 49

VERSION XGAD9B11 5100

If you need to go back to the previous OSD menu screen, press the MENU

key.

Verti al & Horizontal Position Adjustment

1. Use the selection key to move to the icon, then press - & + to move

the whole screen left or right to the center position.

2. Use the selection key to move to the icon, then press - & + to move

the whole screen down or up to the center position.

Viewing S reen Size Adjustment

Use the selection key to move to the icon, then press - & + to get the larger

viewingsize.

Phase Adjustment

You can adjust phase tracking of the display signal to reduce display

flicker. An invalid phase tracking will cause unstable and flicking display.

Use the selection key to move to the Phase item, then press - & + to get

better image quality.

All manuals and user guides at all-guides.com

Andere Handbücher für C593

Inhaltsverzeichnis

Andere Microtek Monitor Handbücher

Microtek

Microtek 914SD Bedienungsanleitung

Microtek

Microtek C893 Bedienungsanleitung

Microtek

Microtek 515C Bedienungsanleitung

Microtek

Microtek 512M Bedienungsanleitung

Microtek

Microtek 997M Bedienungsanleitung

Microtek

Microtek C593 Bedienungsanleitung

Microtek

Microtek C997SD Bedienungsanleitung

Microtek

Microtek C580 Bedienungsanleitung

Microtek

Microtek C788 Bedienungsanleitung

Microtek

Microtek 722S Bedienungsanleitung

Microtek

Microtek C589P Bedienungsanleitung

Microtek

Microtek C588 Bedienungsanleitung

Microtek

Microtek 715C Bedienungsanleitung

Microtek

Microtek JTX V7s Bedienungsanleitung

Microtek

Microtek 714S Bedienungsanleitung

Microtek

Microtek 714M Bedienungsanleitung

Microtek

Microtek 710S Bedienungsanleitung

Microtek

Microtek JTX V9s Bedienungsanleitung

Microtek

Microtek C786 Bedienungsanleitung

Microtek

Microtek 201SD Bedienungsanleitung

Microtek

Microtek 729S Bedienungsanleitung

Microtek

Microtek C586P Bedienungsanleitung

Microtek

Microtek 515M Bedienungsanleitung

Microtek

Microtek 527C Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung