Microtek ScanMaker 3740 Handbuch

Troubleshooting Tips

For USB (Universal Serial Bus) interface scanners

Q1:My scanner doesn’t work.

A1:Follow the steps below:

1. Check to make sure that your computer’s USB is enabled.

a) For Windows 98/2000/Me or Windows XP’s Classic

view: Click Start, Setting,andselectControlPanel.

For Windows XP: Click Startand select ControlPanel,

and make sure you choose the “Switch to Classic View”

option on the left side of the window.

b) For Windows 98/Me: Double-click the Systemicon, then select DeviceManager.

ForWindows2000/XP:Double-clicktheSystemicon, thenselect Hardware, then DeviceManager.

c) Click the plus (+) icon before the UniversalSerial Bus Controlleritem.

You should be able to see the drivers below the “Universal Serial Bus Controller” and there should

be no red or yellow mark next to either options.

If the “Universal Serial Bus Controller” option does not appear, this indicates that your computer's

USB interface is disabled. To resolve this problem, see the related documentation that came with

your computer to set the correct BIOS setting to enable your computer’s USB.

for Windows

December 2001

Windows2000

Step 1

Step 4

Windows 98/Me

Step 1

Step 4

Windows XP

Step 1

Step 4

Click here to switch to Classic View

2. Check to make sure that the scanner driver (e.g., ScanWizard 5, ScanWizard Pro, or ScanWizard Pro TX,

etc.) has been installed in your computer. If the scanner driver has not been installed, install your

scanner driver first. (Make sure no cable is connected to your scanner before installing the driver.)

3. Check to make sure that your scanner is correctly installed.

a) Make sure that only one USB cable is connected to your scanner. (You can only use one interface

ata time.)

b) Make sure that you properly connect the scanner's USB cable to your computer.

c) Make sure your scanner is on and is in the ready state.

4. Verify whether your scanner has been detected by your system.

a) For Windows 98/2000/Me or Windows XP’s Classic view: Click Start, Setting, and select Control

Panel.

For Windows XP: Click Start and select Control Panel, and make sure you choose the “Switch to

Classic View” option on the left side of the window.

b) For Windows 98/Me: Double-click the Systemicon, then select DeviceManager.

ForWindows 2000/XP: Double-click theSystemicon, thenselect Hardware,thenDeviceManager.

c) The Imaging Device with the found scanner appears on the Device Manager list, indicating the

scanner is detected.

Note

: A “found” USB scanner message should display on the screen the first time you start

Windows.

Q2:My scanner still doesn’t work even though I have enabled USB.

A2:This problem happens when you successfully install the scanner and then later reconnect the USB

cable to another USB port. In this case, reinstall your scanner driver and the USB scanner.

Q3:No scanner found when I launch scanning software.

A3:Follow the steps below:

1. Unplug the USB cable from your scanner, then uninstall and reinstall the scanner driver.

2. Restart Windows.

3. Reconnect the USB cable to you scanner.

4. Turn off the scanner and turn it back on.

5. The Imaging Device with the “found” scanner appears on the Device Manager list, indicating that the

scanner has been detected and is ready to scan.

Note

: A “found” USB scanner message should display on the screen the first time you start Windows.

Troubleshooting Tips

For USB (Universal Serial Bus) interface scanners

Q1:My scanner doesn’t work.

A1:Follow the steps below:

1. Check to make sure that the scanner driver (e.g., ScanWizard 5, ScanWizard Pro, ScanWizard Pro TX,

etc.) has been installed on your computer. If the scanner driver has not been installed, install the

scanner driver first. (Make sure that no cable is connected to your scanner before installing.)

2. Check to see that you are using Mac OS 8.6 or later.

For Macs with a built-in USB port:

If your Mac OS is not 8.6 or later, update your Mac OS to 8.6 or later, or visit http://www.apple.com

to get a workable USB driver for your currently installed Mac OS.

For Macs without a built-in USB port, but have an installed USB card:

a) Make sure you have the correct driver in your system for your installed USB card.

b) Check to see if your Mac OS is 8.6 or later. If not, update your Mac OS to 8.6 or later, or visit http://

www.apple.com to get the correct USB driver for your currently installed Mac OS.

3. Check to make sure that your scanner is correctly installed.

a) Make sure that only one USB cable is connected to your scanner. (You should use only one

interface at a time.)

b) Make sure you properly connect the scanner's USB cable to your computer.

c) Make sure your scanner is on and is in the ready state.

4. Check to verify whether your scanner has been detected by your Mac OS and try using Apple System

Profiler 2.0 (or later) to see if the scanner is detected on the USB port.

If your Mac OS cannot find your scanner, please visit http://www.apple.com for more information about

USB support for your Macintosh.

Q2:Keyboard inactive or mouse hang-up when scanner was found by system

A2:Reconnect the USB cable, then restart your scanner and computer. If the keyboard or mouse still cannot

function, turn off your Macintosh and scanner, and connect the USB cable to another available USB

port of your Macintosh.

for Macintosh

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Microtek Scanner Handbücher

Microtek

Microtek ScanMaker i800 Bedienungsanleitung

Microtek

Microtek ArtixScan DI 2015c Bedienungsanleitung

Microtek

Microtek FileScan 3125c Bedienungsanleitung

Microtek

Microtek ArtixScanDI 4020 Plus Bedienungsanleitung

Microtek

Microtek ScanMaker i450 Bedienungsanleitung

Microtek

Microtek Bio-1000F Bedienungsanleitung

Microtek

Microtek ScanMaker 3750i Bedienungsanleitung

Microtek

Microtek ScanMaker 9800XL Plus Bedienungsanleitung

Microtek

Microtek ObjectScan 1600 Bedienungsanleitung

Microtek

Microtek ScanMaker 4 Bedienungsanleitung

Microtek

Microtek ArtixScan DI 5230 Bedienungsanleitung

Microtek

Microtek ArtixScan DI 2020 Bedienungsanleitung

Microtek

Microtek ArtixScan 3200XL Bedienungsanleitung

Microtek

Microtek ScanMaker V6UPL Bedienungsanleitung

Microtek

Microtek ArtixScanDI 7200S Bedienungsanleitung

Microtek

Microtek ArtixScan 120tf Bedienungsanleitung

Microtek

Microtek ScanMaker i700 Bedienungsanleitung

Microtek

Microtek ArtixScan 6000XY Bedienungsanleitung

Microtek

Microtek ScanMaker 4 Bedienungsanleitung

Microtek

Microtek Bio-6000 Bedienungsanleitung

Microtek

Microtek XT5820 HS Bedienungsanleitung

Microtek

Microtek Vantas 3000 Bedienungsanleitung

Microtek

Microtek FileScan 3125c Bedienungsanleitung

Microtek

Microtek ScanMaker V6USL Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung