Microtek ScanMaker i800 Bedienungsanleitung

Before

After

I49-003964 A, August 2005

About This Scanning Guide

This Scanning Guide shows you how to use ScanWizard Pro, the professional-grade

scanning software included with the ScanMaker i800. While the Guide lays out only

the most basic scanning scenarios on these pages, ScanWizard Pro can be used for a

wide range of applications involving sophisticated functionalities and advanced

levels of image manipulation and control.

For information on more advanced scanning scenarios, refer to the ScanWizard Pro

User's Guide.Additional information can also be found in the ScanWizard Pro

Reference Manual for detailed discussions of individual scanning commands and

options. Both documents are inAdobeAcrobat PDF format, available for viewing and

printingfromyourMicrotekScanMakeri800ProCD-ROM.

Contents

AboutThis Scanning Guide ...................................................................... 1

Installing Software .................................................................................... 2

PositioningTransparent Film .................................................................... 3

A. Using the EZ-Lock 35mm Slide Holder ....................................... 4

B. Using the EZ-Lock 35mm Filmstrip Holder ................................. 5

C. Using the EZ-Lock 6 x 22 cm (120) Film Holder ........................... 6

D. Using the EZ-Lock 4

x 5

Film Holder ......................................... 7

E. Using the Film Alignment Ruler .................................................. 8

Scanning Guide

ScanMaker i800 Scanning Scenarios with ScanWizard Pro

Scanning Scenarios ................................................................................... 9

Scanning Regular, Non-Damaged Photos ............................................ 10

Scanning Damaged Photos .................................................................... 13

Scanning Regular, Non-Damaged Positive Film ................................... 16

Scanning Regular, Non-Damaged Negative Film .................................. 18

Scanning Damaged Film ......................................................................... 20

2 ScanMaker i800 Pro Scanning Guide

Installing Software

Before scanning with ScanWizard Pro, make sure it has been installed correctly.

Follow the steps below for installation.

PC:

1. Place the AdobeCD-ROM into the CD-ROMdrive, and install the software.

2. Place the MicrotekScanMaker i800Pro CD-ROM into the CD-ROM drive, and

follow the on-screen instructions to install the driver and software.

Note: If the Microtek Software Installer screen does not come up automatically,

double-click the following in succession: “My Computer”; the CD-ROM icon; then

cdsetup.exe to start the installer program.

3. Restart your computer at the end of all software installation.

MAC:

1. Place the AdobeCD-ROM into the CD-ROMdrive, and install the software.

2. Place the MicrotekScanMaker i800Pro CD-ROM into the CD-ROM drive, and

double-click the ScanWizardPro folder and installer icon.

Note: After rebooting your Macintosh, the Microtek software will attempt to locate

your scanner on the system. Since this is your first install and you may have not yet

connected the scanner, simply ignore the message that appears.

ScanMaker i800 Pro Scanning Guide 3

Positioning Transparent Film

Toscan transparent film, use the EZ-Lock™ FilmHolders or FilmAlignmentRuler

included with your ScanMaker i800 package. Use the EZ-Lock Film Holders to scan

standard-sizetransparentfilm such as 35mm slides, 35mm filmstrips, 4" x 5" film,

6x 4.5cm,6 x6cm, 6x7cm,6 x9cm, or6x 17cm(120) film.Usethe FilmAlignment

Ruler to scan non-standard-size transparent film such as 8" x 10" film.

The EZ-Lock Film Holders ensure precise alignment of film and consistent scans

during film scanning.To scan film, use the film holder that correctly matches the film

type to be scanned.

Before proceeding with film scanning, take note of the information presented in the

two sections below.

Removing the Black Mat

The Black Mat is designed to work with scanning of reflective materials such as

photos and printed matter.It is not designed to work with scanning of slides,

negatives, and transparencies. During film scanning, the Black Mat should be

removed to reveal the light source in the scanner for film.

To remove the Black Mat:

Raise the scanner lid, push the Black Mat to the side (1 in diagram) to remove it from

the scanner lid (2 in diagram).

Black Mat

4 ScanMaker i800 Pro Scanning Guide

A. Using the EZ-Lock 35mm Slide Holder

Orient the holder with

the “Microtek” logo

facing up

Toscan 35mm slides, use the EZ-Lock 35mm

Slide Holder, which can hold up to 12

mounted 35mm slides at a time.

1. Place the 35mm slides to be scanned inside the individual frames of the EZ-Lock

35mm Slide Holder. The shiny base of the 35mm slide should be facing down, and

the emulsion side of the slide should be facing up.

2. Raise the scanner lid, then place the EZ-Lock 35mm Slide Holder towards the back

of the scanner, with the loaded film on the scanner glass surface.

Keep calibration strip

on the glass surface clear

and free of any obstruction

To make sure film scanning performs

correctly, place the holder on the

scan bed, correctly oriented and

showing the side with the Microtek

logo face up. Align the red arrows so

that the holder’s front edge is flush

against the top ruler of the scanner.

“Microtek” logo

ScanMaker i800 Pro Scanning Guide 5

B. Using the EZ-Lock 35mm Filmstrip Holder

Orient the holder with the

“Microtek” logo facing up

Toscan 35mm filmstrips, use the EZ-Lock

35mmFilmstrip Holder,whichcan

simultaneously hold four strips of 6 frames

each, or a total of 24 frames.

1. Place the 35mm filmstrip to be scanned inside theframeofthe EZ-Lock 35mm

Filmstrip Holder. The shiny base of the 35mm filmstrip should be facing down, and

the emulsion side of the filmstrip should be facing up.

2. Raise the scanner lid, then place the EZ-Lock 35mm Filmstrip Holder towards the

back of the scanner, with the loaded film on the scanner glass surface.

Keep calibration strip

on the glass surface clear

and free of any obstruction

To make sure film scanning performs

correctly, place the holder on the

scan bed, correctly oriented and

showing the side with the Microtek

logo face up. Align the red arrows so

that the holder’s front edge is flush

against the top ruler of the scanner.

“Microtek” logo

6 ScanMaker i800 Pro Scanning Guide

C. Using the EZ-Lock 6 x 22 cm (120) Film Holder

To scan 6x4.5cm, 6 x6cm,6 x 7cm,6x 9

cm, and6 x 17 cmfilm,usethe EZ-Lock 6 x

22cm(120)FilmHolder,which can hold up

to4 pieces of 6 x 4.5 cm film, 2pieces of 6 x

9cmfilm, or a singlepieceof6x 17 cm film.

1. Place the 120 film to be scanned inside the EZ-Lock 6x 22 cm (120) Film Holder, as

indicated in the graphics below. The shiny base of the 120 film should be facing

down, and the emulsion side of the filmstrip should be facing up.

2. Raise the scanner lid, then place the EZ-Lock 6 x 22 cm (120) Film Holder towards

the back of the scanner, with the loaded film on the scanner glass surface.

b) Place the film face

down into the holder.

a) Push on the side to

open the lid. c) Pull down the side

to close the lid.

Keep calibration strip

on the glass surface clear

and free of any obstruction

To make sure film scanning performs

correctly, place the holder on the

scan bed, correctly oriented and

showing the side with the Microtek

logo face up. Align the red arrows so

that the holder’s front edge is flush

against the top ruler of the scanner.

“Microtek” logo

ScanMaker i800 Pro Scanning Guide 7

D. Using the EZ-Lock 4" x 5" Film Holder

To scan 4" x 5" film, use the EZ-Lock 4" x 5"

Film Holder, which can hold up to 2 pieces of

4"x5" film at a time.

1. Place the 4" x 5" film to be scanned inside the EZ-Lock 4" x 5" Film Holder, as

indicated in the graphics below. The shiny base of the 4" x 5" film should be

facing down, and the emulsion side of the filmstrip should be facing up.

2. Raise the scanner lid, then place the EZ-Lock 4" x 5" Film Holder towards the back

of the scanner, with the loaded film on the scanner glass surface.

b) Place the film face

down into the holder.

a) Push on the side to

open the lid. c) Pull down the side

to close the lid.

Keep calibration strip

on the glass surface clear

and free of any obstruction

To make sure film scanning performs

correctly, place the holder on the

scan bed, correctly oriented and

showing the side with the Microtek

logo face up. Align the red arrows so

that the holder’s front edge is flush

against the top ruler of the scanner.

“Microtek” logo

8 ScanMaker i800 Pro Scanning Guide

E. Using the Film Alignment Ruler

Important: Align the Film Alignment

Ruler firmly against the top ruler of the

scanner, with the ruler oriented

correctly and with the correct side up.

During placement of the Ruler, make

sure that the calibration strip on the

Ruler is kept clear and free of

obstruction at all times.

Calibration strip

To scan non-standard-size film such as

8"x10" film, use the FilmAlignment Ruler,

which allows you to scan film up to

8"x12"insize.

1. Place the FilmAlignment Ruler towards the back of the scanner on the scanner

glass surface.

2. Place the film (non-standard size film) to be scanned on the scanner glass surface,

and center the film along the FilmAlignment Ruler on the scanner.

ScanMaker i800 Pro Scanning Guide 9

Scanning Scenarios

The following pages provide various scenarios for scanning with the ScanMaker i800

by using ScanWizard Pro, including the following:

• Scanning regular, non-damaged photos: This scenario can also be your first scan

in order to familiarize yourself with scanning basics.

• Scanning damaged photos: This scenario utilizes DIGITAL ICE for reconstructing

damaged photos.

• Scanning regular, non-damaged positive film: This scenario details the steps for

scanning positive film, such as 35mm mounted slides.

• Scanning regular, non-damaged negative film: This scenario details the steps for

scanningnegativefilm,such as 35mm filmstrips, 6 x 4.5 cm, 6 x6cm,6x7cm,6 x 9

cm,6x17 cmfilm,and4"x5"film.

• Scanningdamaged film:This scenario utilizesDIGITALICEforcorrectingflaws

that may be present in your slides, negatives, and transparencies.

Take note that with the use of ScanWizard Pro, the Smart Touch buttons located on

the front panel of the ScanMaker i800 are deactivated and become unavailable for

use. The Smart Touch buttons are intended to be used in conjunction with

ScanWizard 5, Microtek's other scanning software also included with the ScanMaker

i800, geared for tasks assigned to the buttons.

Note: In the following pages that detail the various scanning scenarios, the

ScanWizard Pro interface is shown with the Preview, Settings, and Scan Job Queue

windows as they appear in Mac OS X.

The appearance of the windows will change slightly in Windows for the PC

platform, but the location of the various commands and icons remain in

approximately the same locations throughout the ScanWizard Pro interface.

10 ScanMaker i800 Pro Scanning Guide

Scanning Regular, Non-Damaged Photos

1. Raise the scanner lid, and place the

photo to be scanned face down on

the scanner glass surface. Position

the top end of the photo towards the

back of the scanner.

Make sure the Black Mat is attached

on the scanner lid, then close the

scanner lid before you launch

ScanWizardPro.

2. Launch ScanWizard Pro either as a stand-alone by clicking the program icon, or by

using the File-Import / File-Acquire command from your image-editing program

(such as Adobe Photoshop). Alternatively, you can start ScanWizard Pro from the

Applicationsfolder in your Mac OS X.

The first time you launch ScanWizard Pro, you will be prompted to set up color

matching for your scanner. If you are not sure about what to do, simply click the

OK button to accept the settings. You can always change the settings at a later

time.

For more information, see the Color Matching Setup section in the ScanWizard

Pro Reference Manual in the Microtek ScanMaker i800 Pro CD-ROM.

The Black Mat

comes

preattached to

the scanner lid.

3. Go to the Preview window of

ScanWizard Pro, and choose

Reflectivefrom the Scan

Materialmenu.

Color Matching

features

Andere Handbücher für ScanMaker i800

Inhaltsverzeichnis

Andere Microtek Scanner Handbücher

Microtek

Microtek ScanMaker 1000XL Bedienungsanleitung

Microtek

Microtek ArtixScan 120tf Bedienungsanleitung

Microtek

Microtek LightLid 35 Bedienungsanleitung

Microtek

Microtek ScanMaker i900 Bedienungsanleitung

Microtek

Microtek ArtixScan 120tf Bedienungsanleitung

Microtek

Microtek ArtixScanDI 5230 Bedienungsanleitung

Microtek

Microtek ArtixScanDI 4020 Plus Bedienungsanleitung

Microtek

Microtek XT3500 Bedienungsanleitung

Microtek

Microtek ScanMaker 1000XL Bedienungsanleitung

Microtek

Microtek ScanMaker i700 Bedienungsanleitung

Microtek

Microtek ScanMaker 4800 Bedienungsanleitung

Microtek

Microtek ScanMaker 8700 Bedienungsanleitung

Microtek

Microtek ArtixScan DI 2020 Montageanleitung

Microtek

Microtek FileScan 3125c Bedienungsanleitung

Microtek

Microtek Vantas 3000 Bedienungsanleitung

Microtek

Microtek Bio-5000 Plus Betriebsanleitung

Microtek

Microtek ScanMaker 6000 Handbuch

Microtek

Microtek ScanMaker 3700 Bedienungsanleitung

Microtek

Microtek ScanMaker i900 Bedienungsanleitung

Microtek

Microtek ScanMaker i280 Bedienungsanleitung

Microtek

Microtek ScanMaker 8700 Bedienungsanleitung

Microtek

Microtek ScanMaker 1000XL Bedienungsanleitung

Microtek

Microtek ScanMaker 3600 Bedienungsanleitung

Microtek

Microtek ScanMaker i300 Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung