Miele KM 3054-1 Bedienungsanleitung
11199440-01
Installation
*INSTALLATION*
Safety instructions for installation
Risk of damage from incorrect connection.
Incorrect installation can cause damage to the hob.
The hob must only be installed by a qualified person.
Damage from falling objects.
Take care not to damage the hob when fitting wall units or a cooker hood above
it.
Fit the wall units and the cooker hood before the hob.
The room in which the hob is installed must conform to all relevant
local and national building regulations and safety regulations.
The veneer or laminate coatings of worktops (or adjacent kitchen
units) must be treated with 100°C heat-resistant adhesive which will
not dissolve or distort. Any backmoulds must be of heat-resistant
material.
The hob must not be installed over a fridge, fridge-freezer, freezer,
dishwasher, washing machine, washer-dryer or tumble dryer.
A gas hob must not be installed directly next to a deep fat fryer as
the gas flames could ignite the fat in the fryer. It is essential to
maintain a distance of at least 300mm between these two
appliances.
When installing the hob, make sure that the gas pipe and
electrical connection cable cannot come into contact with hot
appliance parts.
The electrical cable and any flexible gas connection pipes must be
installed in such a way so that they do not come into contact with
any moving kitchen parts (e.g. a drawer), and cannot become
trapped.
Observe carefully the safety clearances listed on the following
pages.
11199440-01
Installation
*INSTALLATION*
Safety distances
Safety distance above the hob
A minimum safety distance must be
maintained between the appliance and
the cooker hood above it. See the
cooker hood manufacturer's operating
and installation instructions for details.
If the manufacturer's instructions are
not available for the cooker hood or if
any flammable objects (e.g. utensil rails,
wall units etc) are installed above the
hob a minimum safety distance of at
least 760mm must be maintained
between them and the appliance below.
When two or more appliances which
have different safety distances are
installed together below a cooker
hood, you should observe the
greatest safety distance.
11199440-01
Installation
*INSTALLATION*
Safety distances to the sides and
back of the hob
Ideally the hob should be installed with
plenty of space on either side. There
may be a wall at the rear or a tall unit or
wall on one side (right or left) (see
illustrations).
Minimum distance between the back
of the worktop cut-out and the rear
edge of the worktop:
50mm
Minimum distance between the
worktop cut-out and a wall or tall unit to
the right of it:
150mm.
Minimum distance between the
worktop cut-out and a wall or tall unit to
the left of it:
150mm.
Not allowed
Highly recommended
Not recommended
Not recommended
11199440-01
Installation
*INSTALLATION*
Safety distance when installing the appliance near a wall with additional
niche cladding
A minimum safety distance must be maintained between the worktop cut-out and
any niche cladding to protect it from heat damage.
If the niche cladding is made from a combustible material (e.g. wood) a minimum
safety distance of 50 mm must be maintained between the cut-out and the
cladding.
If the niche cladding is made from a non-combustible material (e.g. metal, natural
stone, ceramic tiles) the minimum safety distance between the cut-out and the
cladding will be 50 mm less the thickness of the cladding.
Example: 15 mm niche cladding
50mm - 15mm = minimum safety distance of 35mm
Flush-fitted hobs Hob with frame or bevelled edge
aMasonry
bNiche cladding dimension x = thickness of the niche cladding material
cWorktop
dWorktop cut-out
eMinimum distance to
combustible materials 50mm
non-combustible materials 50mm - dimension x
11199440-01
Installation
*INSTALLATION*
Installation notes
Seal between the hob and the
worktop
Damage caused by incorrect
installation.
Using sealant under the hob could
result in damage to the hob and the
worktop if the hob ever needs to be
removed for servicing.
Do not use sealant between the hob
and the worktop.
The sealing strip under the edge of
the hob provides a sufficient seal for
the worktop.
Tiled worktops
Grout lines and the hatched area
underneath the hob frame must be
smooth and even. If they are not the
hob will not sit flush with the worktop
and the sealing strip underneath the
hob will not provide a good seal
between the hob and the worktop.
Sealing strip
Dismantling the hob for service
purposes may damage the sealing
strip underneath the edge of the hob.
Always replace the sealing strip
before reinstalling the hob.
11199440-01
Installation
*INSTALLATION*
Building-in dimensions
All dimensions are given in mm.
aFront
bCasing depth
cMains connection box with mains connection cable, L = 2000mm
dGas connection R ¹/₂ - ISO 7-1 (DIN EN 10226)
eElectronics housing, maximum casing depth 78mm
11199440-01
Installation
*INSTALLATION*
Installation
Preparing the worktop
Create the worktop cut-out as shown
in the hob diagram. Remember to
maintain the minimum safety
distances (see “Installation – Safety
distances”).
Seal any cut surfaces on wooden
worktops with a special varnish,
silicone sealant or resin to prevent the
wood from swelling as a result of
moisture ingress. The sealant must
be heat-resistant.
Make sure that the sealant does not
come into contact with the top of the
worktop.
The seal under the appliance ensures
that the hob will sit securely in the cut-
out without slipping. Any gap between
the appliance frame and worktop will
become smaller over time.
Installing the hob
Stick the supplied sealing strip under
the edge of the hob.
Feed the power cable for the hob
down through the worktop cut-out.
Place the hob loosely in the cut-out.
When doing this, make sure that the
seal of the appliance sits flush with
the worktop on all sides. This is
important to ensure an effective seal
all round.
If the seal does not sit flush with the
worktop in the corners, the corner
radius (≤R4) can be carefully cut to fit
using a jigsaw.
Do not use any additional sealant
(e.g. silicone) on the hob.
Connect the hob to the electricity
supply (see “Installation – Electrical
connection”).
Connect the hob to the gas supply
(see “Installation – Gas connection”).
11199440-01
Installation
*INSTALLATION*
Securing the hob
Secure the hob using the brackets
supplied.
Functional check
After installing the hob, ignite all
burners to check that they are
operating correctly:
- The flame must not go out on the
lowest setting, or when the control is
turned quickly from the highest to the
lowest setting.
- On the highest setting, the flame
must have a distinctive and visible
core.
11199440-01
Installation
*INSTALLATION*
Gas connection
Risk of explosion due to an
incorrect gas connection.
If the gas connection is carried out
incorrectly, it may result in gas
leakage.
Connection to the gas supply must
only be undertaken by an approved
and registered gas installer in strict
accordance with current local and
national safety and building
regulations. The installer is
responsible for ensuring that the
appliance functions correctly when
installed.
Risk of explosion due to an
incorrect conversion.
If the conversion to another type of
gas is carried out incorrectly, it may
result in gas leakage.
Conversion from one type of gas to
another must only be undertaken by
an approved and registered gas
installer in strict accordance with
current local and national safety and
building regulations. The installer is
responsible for ensuring that the
appliance functions correctly when
installed.
The gas connection must be
installed so that connection can be
made either from inside or outside
the kitchen furniture unit. The
isolating valve must be easily
accessible and visible (by opening
the cabinet door if necessary).
Check with your local gas supplier
about the type of gas supplied and
compare this information with the
type of gas quoted on the
appliance's data plate.
The hob is not connected to an
exhaust flue.
When installing and connecting the
appliance please observe all relevant
installation instructions and ensure it
has adequate ventilation once
installed.
The gas connection must be made in
accordance with national and local
regulations.
Any special local conditions relating
to gas installations as well as
building regulations must also be
observed.
Risk of heat damage.
Gas connections, pipes and
connection cables can suffer
damage if exposed to heat from the
hob.
After installation make sure that
neither the gas pipe nor the mains
cable can come into contact with hot
parts of the appliance and that the
gas pipe and connections on the hob
cannot come into contact with hot
gas exhaust.
11199440-01
Installation
*INSTALLATION*
Risk of explosion due to
damaged gas pipes.
Gas can leak from damaged flexible
gas pipes.
Attach flexible gas pipes in such a
way so that they do not come into
contact with any moving kitchen
parts (e.g. a drawer) and are not
exposed to mechanical stress.
Connect the hob to the gas supply in
accordance with national and local
regulations. Check the gas
connection for any leaks.
Depending on country of destination
this appliance is set up for connection
to natural or liquid gas. See adhesive
label on the appliance.
Depending on country of destination,
jets are supplied for conversion to a
different type of gas. If the appropriate
jets have not been supplied with the
appliance, you will need to contact your
Miele dealer. Conversion to another
type of gas is described in the section
“Converting to another type of gas”.
Connecting the hob
The hob is supplied with a conical ¹/₂"
gas connection point. There are two
connection options:
- Fixed connection
- Flexible connection in accordance
with DIN 3383 Part 1, maximum
length 2000 mm.
Risk of explosion due to gas
leakage.
Unsuitable sealant will not ensure the
required leak protection for
connections.
Ensure that a suitable sealant is
used.
Using a 90° angle
cConnection R¹/₂"
d90° elbow
The installation height in the area of
the gas connection is increased by
approx. 60mm.
Andere Handbücher für KM 3054-1
2
Inhaltsverzeichnis
Andere Miele Kochfeld Handbücher
Miele
Miele KM 247 Bedienungsanleitung
Miele
Miele KM 423 Bedienungsanleitung
Miele
Miele ProLine CS 1013-1 Bedienungsanleitung
Miele
Miele CS 1134 Technisches Datenblatt
Miele
Miele KM 5673 Technisches Datenblatt
Miele
Miele KM 2356-1 Bedienungsanleitung
Miele
Miele KMR 1124LP Bedienungsanleitung
Miele
Miele KM 6112 Bedienungsanleitung
Miele
Miele KMR 1124 Bedienungsanleitung
Miele
Miele KM 5775 Montageanleitung
Miele
Miele KM 7564 FR Bedienungsanleitung
Miele
Miele KM 6342 Technisches Datenblatt
Miele
Miele KMDA 7676 Bedienungsanleitung
Miele
Miele SmartLine CS 7101-1 Bedienungsanleitung
Miele
Miele KM 5617 Montageanleitung
Miele
Miele KM 6629 Montageanleitung
Miele
Miele KM 2335 Bedienungsanleitung
Miele
Miele KM 417 Bedienungsanleitung
Miele
Miele KM6357 Montageanleitung
Miele
Miele CS 1326 Technisches Datenblatt
Beliebte Kochfeld Handbücher anderer Marken
Bauknecht
Bauknecht Hob Bedienungsanleitung
Zanussi
Zanussi ZGM 782 Bedienungsanleitung
dipo INDUCTION
dipo INDUCTION DIBK218S Bedienungsanleitung
Blomberg
Blomberg MKN 24201 W Bedienungsanleitung
Progress
Progress PAI3101F Bedienungsanleitung
Hotpoint Ariston
Hotpoint Ariston PKL 641 IX/HA Bedienungsanleitung