Miele K 31222 Ui Bedienungsanleitung
10841790-04
Electrical connection
*INSTALLATION*
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an AC single-phase 220–
240V50Hz supply.
The fuse rating must be at least 10A.
This appliance must be connected to a
suitable switched socket. The electrical
installation must be in compliance with
current local and national safety
regulations.
The socket must not be concealed
behind the appliance and must be
easily accessible so that the appliance
can be quickly disconnected from the
electricity supply in case of an
emergency.
If the socket is no longer accessible
after installation, an additional means of
disconnection must be provided for all
poles. Suitable means of disconnection
include switches with an all-pole
contact gap of at least 3mm. These
include isolator switches, fuses and
relays.
The mains plug and mains connection
cable must not come into contact with
the back of the appliance as vibrations
can cause damage to these
components. This could result in a short
circuit.
Nor should other appliances be
plugged into a socket located directly
behind this appliance.
Do not connect the appliance to the
mains electricity supply using an
extension lead. Extension leads do not
guarantee the required safety of the
appliance (e.g. danger of overheating).
Temporary or permanent operation with
a self-sufficient or non-mains
synchronous energy supply system
(e.g. isolated networks, back-up
systems) is possible. A requirement for
the operation is that the energy supply
system complies with all current local
and national requirements that apply to
stand-alone, solar and/or battery
systems”.
The protective measures provided in
the domestic installation and in this
Miele product must also be assured in
their function and operation in isolated
operation or in non-mains synchronous
operation, or replaced with equivalent
measures in the installation.
If the mains cable needs to be replaced,
this must be done by a qualified and
competent electrician.
10841790-04
Installing the appliance
*INSTALLATION*
To install the appliance, you
will need the following tools:
Parts required for installation
All installation parts are designated by
number. This numbering is also used in
the installation instructions.
Preparing the appliance
Position the appliance in front of the
housing unit.
Grasp the plinth cover at the side and
pull it off towards the front.
You have a choice of two different
ways of securing your appliance:
1. Top mounting
This type of mounting is suitable for
mounting under worktops made of
synthetic materials, e.g. laminate.
The worktop must be suitable for
screwing a mounting bracket onto.
With the appliance feet fully extended
the appliance should sit lightly
tensioned between the floor and the
worktop.
2. Side mounting
This type of mounting is suitable for
mounting under hard worktops, e.g.
granite. Furniture side walls are
needed to the right and left of the
refrigerator, to which the mounting
brackets can be screwed.
With the feet fully extended the
refrigeration appliance will sit lower
than the worktop.
10841790-04
Installing the appliance
*INSTALLATION*
1. Top mounting
Fit the bracket in the opening in the
appliance lid.
Bend the bracket at the perforated
point.
2. Side mounting
Both ends of the bracket must be
bent.
Fit the bracket in the opening in the
appliance lid.
Bend the bracket at the perforated
point.
Remove the bracket from the opening
and insert the straight end of the
bracket.
Now bend this end of the bracket at
the perforated point.
10841790-04
Installing the appliance
*INSTALLATION*
Pushing the appliance into its
niche
When pushing the appliance into
its niche make sure that the mains
cable does not get trapped.
Move the appliance carefully on
floors that are sensitive to scratching
to prevent damage.
The appliance feet can break off.
The feet should be almost fully
screwed in when you push the
appliance into the niche.
Useful tip: Loosen the two rear feet by
half a turn before pushing the appliance
in. After pushing it into the niche the
feet will be easier to adjust from the
front (see “Aligning the appliance”).
Position the mains electricity cable so
that the appliance can be connected
easily once installed.
Useful tip: To help you push the
appliance into position, tie a piece of
string around the plug to “increase” the
length of the connection cable.
Then pull the cable by the end of the
string through the housing unit.
If the appliance is pushed too far into
the niche, the door may not close
properly once the furniture panel has
been fitted. This can cause ice to
build up, condensate to accumulate
and lead to faults in the appliance.
These can all lead to increased
energy consumption.
Push the appliance into the building-
in niche making sure a gap of 42mm
is maintained all round between the
appliance body and the front of the
housing unit side walls.
Push the appliance into the niche
until the front edges of the hinges at
the top and bottom are flush with the
front edge of the housing unit side
wall.
This will create a gap all round of
42mm to the front edges of the
housing unit side walls.
10841790-04
Installing the appliance
*INSTALLATION*
With furniture with door fittings (e.g.
stubs, seals etc.) the dimension of
these must be taken into account
when making sure there is a gap all
round of 42mm.
Pull the appliance forwards by the
appropriate dimension.
Check again to make sure there is a
gap of 42mm to the front edges of
the door fittings.
Useful tip: If possible, remove door
fittings and push the appliance into the
niche until all fixing brackets at the top
and bottom are in line with the front
edge of the housing unit side wall.
Aligning the appliance
When securing the appliance in the
niche at the top, the appliance
should sit lightly tensioned between
the floor and the worktop.
Adjust the front and rear feet
alternately according to the height of
the niche and make sure the
appliance is correctly aligned.
Proceed as follows:
Adjust both rear feet with appropriate
screws at the front right and left in the
appliance plinth using a flat-tip
screwdriver.
Use an Allen key to unscrew both
front feet.
Useful tip: As soon as the feet have
been unscrewed slightly, you can adjust
them with a screwdriver at the bottom
of the foot (see small illustration).
10841790-04
Installing the appliance
*INSTALLATION*
The foam ensures the airflow
is separated to prevent
malfunctioning of the appliance.
Insert the piece of foam supplied.
Refit the plinth panel, but do not
secure it in position yet.
Without a continuous plinth panel:
Pull the plinth panel forwards until
the ventilation slats are in alignment
with adjacent cabinet plinth panels.
Hold the plinth panel securely and
attach it to the right and left using the
bolts supplied.
With a continuous plinth panel:
Push the plinth panel right up
against the refrigerator and attach it
to the right and left using bolts.
Fitting a continuous furniture
plinth panel
Ventilation takes place through a
ventilation grille in the appliance
plinth.
The ventilation gaps must never be
obstructed.
If a continuous plinth panel is to be
fitted, a suitable ventilation gap will
need to be made in it for the
ventilation grille of the appliance:
Trim the furniture plinth panel (U) to
the correct height.
Adjust the height (V) along the niche
width (W) underneath the appliance
plinth .
10841790-04
Installing the appliance
*INSTALLATION*
Securing the appliance in the
niche
1. Top mounting
2. Side mounting
Screw the appliance into position on
the right and the left.
Fitting a furniture door
If the appliance is being built into a run
of units, the height of the furniture
door should be aligned with adjacent
kitchen units.
The furniture door must be mounted
plane and free of tension.
The following chapter describes the
installation of a furniture door with a
furniture front of at least 16-19mm
thickness.
Ensure that the plinth panel is refitted
correctly.
A gap of 8mm is set at the factory
between the appliance door and the
fixing bracket. Double-check this gap
and adjust it if necessary.
Push the fitting aids up to the
height of the furniture door: the lower
edge X of the fitting aids must be at
the same height as the upper edge of
the furniture door being fitted (see
in diagram).
10841790-04
Installing the appliance
*INSTALLATION*
Useful tip: Push up the fitting aids
with the furniture front.
Undo the nuts and take the fixing
bracket off together with the fitting
aids.
Place the furniture door with the outer
side downwards on a stable surface.
Using a pencil, lightly mark a line
down the centre of the inside of the
furniture door.
Hang the fixing bracket with the
fitting aids onto the inside of the
furniture door. Align the fixing bracket
centrally.
Attach the fixing bracket securely
using at least 6 short chipboard
screws. (On cassette doors only
use 4 screws on the edges). Drill pilot
holes into the furniture door if
necessary.
Pull the fitting aids upwards to
remove them .
Turn them around and fit them into
the middle slots on the fixing bracket
for safe keeping.
10841790-04
Installing the appliance
*INSTALLATION*
Fit the side cover to the fixing bracket
on the opposite side of the hinge.
Turn the furniture door over and
attach the handle (if needed).
Open the appliance door.
Hang the furniture door onto the
adjusting bolts.
Loosely attach the nuts on the
adjusting bolts.
Close the door and check the
distance between the door and
neighbouring furniture doors.
Align to match neighbouring doors if
necessary:
Side adjustments X are made by
sliding the furniture door, and height
adjustments Y by turning the
adjusting bolts with a screwdriver.
10841790-04
Installing the appliance
*INSTALLATION*
Whilst counterholding the adjusting
bolts with a screwdriver, tighten
the nuts on the appliance door
with screwdriver.
Attach the appliance door and the
furniture door using screws through
the fixing brackets:
- Drill holes in the furniture door (mark
the position of the holes first).
- Screw in the short chipboard
screws (4 x 14mm).
Align the furniture door along the
depth plane Z: loosen the screws in
the long slots at the top of the
appliance door as well as under
the appliance door. By moving the
furniture door, create a gap of 2mm
between the furniture door and the
front edge of the niche. Align
according to the adjacent furniture
doors.
Close the door, check that it is
secured correctly, and align it with
adjacent furniture doors.
Tighten all screws again.
Andere Handbücher für K 31222 Ui
7
Inhaltsverzeichnis
Andere Miele Kühlschrank Handbücher
Miele
Miele KF 1911 Vi Technisches Datenblatt
Miele
Miele K 37472 iD Bedienungsanleitung
Miele
Miele KD 683 i-3 Technisches Datenblatt
Miele
Miele K 14820 SD ed Montageanleitung
Miele
Miele K 1801 Vi Technisches Datenblatt
Miele
Miele K 2202 S-1 Technisches Datenblatt
Miele
Miele KF 2981 Vi Bedienungsanleitung
Miele
Miele KDN 9713 iD Technisches Datenblatt
Miele
Miele K 14827 SD ed/cs Technisches Datenblatt
Miele
Miele KFN 37452 iDE Bedienungsanleitung
Miele
Miele K 9758 iDF Technisches Datenblatt
Miele
Miele K 31222 Ui Bedienungsanleitung
Miele
Miele K 32122 i Bedienungsanleitung
Miele
Miele K 14820 SD ed Technisches Datenblatt
Miele
Miele KS 37472 iD Bedienungsanleitung
Miele
Miele KF 18 Vi Series Bedienungsanleitung
Miele
Miele KFN 37232 iD Bedienungsanleitung
Miele
Miele KF 3855 S6 Technisches Datenblatt
Miele
Miele KFN 29233 D bb Bedienungsanleitung
Miele
Miele K 622 Ui Technisches Datenblatt
Beliebte Kühlschrank Handbücher anderer Marken
Bonnet Neve
Bonnet Neve SKYVIEW PLUS Bedienungsanleitung
Zanussi Electrolux
Zanussi Electrolux ZERB 8441 Bedienungsanleitung
Sharp
Sharp SJ-BA31IEXW2-EU Bedienungsanleitung
CORBERO
CORBERO CC2300MCW Bedienungsanleitung
KitchenAid
KitchenAid 2205264 Bedienungsanleitung
Stengel
Stengel KU 1101 A++ Bedienungsanleitung
