MikroTik AP Bedienungsanleitung

Network Controller and Access Point

Staging Guide

Overview

This guide provides instructions on configuring and staging the MikroTik Access Point

(AP) and Network Controller (NC) so that they can connect to the Viasat Network once

installed.

The NC and AP must be staged before installation deployment. This process does

not require an internet connection and devices need only be staged once. In order to

ensure devices are staged with up-to-date software, they should be staged directly prior

to shipment for installation (as part of the pre-installation process).

Connection to Viasat satellite infrastructure is NOT required for staging these devices.

REQUIRED ITEMS:

•One Mikrotik Network Controller (NC)

•One Mikrotik Access Point (AP)

•One NC power cord (The power cord that comes with the AP is not needed)

•One NC PoE injector (The PoE injector that comes with the AP is not needed)

•One Android smartphone with 802.11 a/b/g/n WiFi capability and with the latest

version of the VCI Staging Application installed.

oThe Android smartphone must also have an approved OS version.

•Two pre-tested Ethernet cords

•Working power outlet

•Paperclip or other fine-pointed object

NOTE: Use the following link as reference when installing the Staging Application to

your device: https://www.lifewire.com/install-apk-on-android-4177185

NOTE: A different model may be used for the MikroTIK items pictured in this guide, but

the process is identical.

Network Controller (NC)

Access Point (AP)

PoE Injector

NC/AP Staging Instructions:

1. Plug the NC power cord into the PoE injector as shown below and connect the power

cord to a functioning power outlet. Plug an ethernet cable to the other end of the PoE

injector, a light on the injector indicates successful connection to power.

2. Perform a Factory Reset on the NC: Hold down the NC reset button (circled below) and

THEN insert the other end of the ethernet cord connected to the PoE injector into Port 1

of the NC as shown below. The reset button must be held down BEFORE connecting the

ethernet cable.

Continue holding the reset button until LED light starts flashing (takes 5 seconds) then

immediately release the button to reset RouterOS configuration.

NOTE: If the reset button is held down too long the LED will turn solid. If this happens,

unplug the ethernet cable and perform another factory reset.

3. Connect the second ethernet cable to Port 5 of the NC as show below.

4. Perform a Factory Reset of the AP: Hold down the AP reset button (circled below, this

may require a paper clip or other small object to reach) and THEN connect the other

end of the ethernet cable in Port 5 of the NC to the AP’s ethernet port as shown below. The

reset button must be held down BEFORE connecting the ethernet cable.

NOTE: If the reset button is held down too long the LED will turn solid. If this happens,

unplug the ethernet cable and perform another factory reset.

5. Verify the Power and Port 5 lights are on for the NC and the power light is on for the AP.

If this does not happen, try repeating the above steps.

6. On your 5GHz Android smartphone, go to settings and verify Location Services is set to

On using the below image as reference.

7. Open the VCI Staging Application. The below screen will load. If no Available Networks

appear then press “SCAN FOR WI-FI NETWORKS”.

NOTE: Available Networks will not show if Location Services is disabled or if devices

are not powered on. If the issue persist, try using a different 5GHz Android device

contact Support.

8. Connect to the Network Controller (NC) Wi-Fi by selecting the Available Network that

uses the last 6 digits of the WLAN number (circled below) on the back of the NC. Your 6

digits will differ from the ones shown below.

9. Press “CONFIRM” on the pop-up screen.

NOTE: Configuring the NC will automatically configure the AP.

10. The Staging App will complete the below processes. This may take up to 15 minutes and

the devices may reboot several times. To ensure the device does not enter Sleep Mode

during this process, tap the screen every 15 to 20 seconds.

11. A Succesful Configuration will be confired by displaying the screen shown below on the

Android smartphone. Congratulations, NC/AP Staging is complete! The devices are now

ready for deployment to the installation site.

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere MikroTik Netzwerk-Hardware Handbücher

MikroTik

MikroTik 2004-1G-12S+2XS Bedienungsanleitung

MikroTik

MikroTik CSS610-8G-2S+IN Bedienungsanleitung

MikroTik

MikroTik FiberBox Plus Bedienungsanleitung

MikroTik

MikroTik CCR1009-7G-1C-1S+ Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 33/433AH Bedienungsanleitung

MikroTik

MikroTik Wireless Wire Bedienungsanleitung

MikroTik

MikroTik nRAY Series Bedienungsanleitung

MikroTik

MikroTik Chateau LTE18 ax Bedienungsanleitung

MikroTik

MikroTik CRS112-8P-4S-IN Bedienungsanleitung

MikroTik

MikroTik Chateau LTE12 Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 800 Series Bedienungsanleitung

MikroTik

MikroTik Woobm-USB Bedienungsanleitung

MikroTik

MikroTik RouterBOARD SXT G-2HnD Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 2011U Series Bedienungsanleitung

MikroTik

MikroTik CCR2004-1G-2XS-PCIe Bedienungsanleitung

MikroTik

MikroTik PL7411-2nD Kurzanleitung

MikroTik

MikroTik RBLDF-5nD Bedienungsanleitung

MikroTik

MikroTik hAP lite Bedienungsanleitung

MikroTik

MikroTik cAP ax Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 750 Bedienungsanleitung

MikroTik

MikroTik ATL LTE18 kit Bedienungsanleitung

MikroTik

MikroTik Chateau 5G ax Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 411R Bedienungsanleitung

MikroTik

MikroTik LHG 60G Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung