MikroTik CCR1009-7G-1C-1S+ Bedienungsanleitung

CCR1009-7G-1C-1S+

1U rackmount, 7x Gigabit Ethernet, 1x Combo port (SFP or Gigabit Ethernet), 1xSFP+ cage, 9 cores x 1.2 GHz CPU, 2GB RAM, LCD panel, Dual Power

supplies, SmartCard slot, RouterOS L6.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.

Quick start

Mount unit or place on the flat surface, please see paragraph for instructions.Mounting

Connect two powering units to the AC source using provided power cords.

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility.

Use Winbox to connect to the default IP address of 192.168.88.1 from any port, with the username admin and no password.

We recommend clicking the "Check for updates" button and updating your system software to the latest version to ensure the best performance

and stability.Detailed info on how to upgrade the device ;https://mt.lv/upgrade

Set up your password to secure the device.

Mounting

The device is designed to use indoors and it can be mounted in a rackmount enclosure using provided rack mounts, or it can be placed on the desktop.

Please attach rubber pegs on the bottom of the router if the desired placement is on the flat surface or use a Phillips screwdriver to attach rackmount ears

on both sides of the device if designated use is for rackmount enclosure:

Attach rack ears to both sides of the device and tighten four screws to secure them in place, as shown in the picture.

Place the device in a rackmount enclosure and align with the holes so that the device fits conveniently.

Tighten screws to secure it in place.

The device has no protection from water contamination, please ensure the placement of the device in a dry and ventilated environment.

We recommend

shielded Cat5/6 cables for our devices. Mounting and configuration of this device should be done by a qualified person.

Powering

The device accepts powering in the following ways:

Dual power supplies for redundancy, 110-240 V AC two inputs, IEC connectors.

PoE input on Ether7 (labeled PoE/Boot), 15-57 V passive PoE only. For alternative use only.

Maximum power consumption 34 W. With attachments 39 W.

Connecting to a POE Adapter:

Connect the Ethernet cable from the device Eth7 to the POE out port of the POE adapter.

Connect an Ethernet cable from your LAN to the POE adapter.

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Resetting the device

In case you wish to return the device to its original configuration, you can use the RESET button. Hold this button during boot time until LED lights start

flashing, then release the button to reset RouterOS configuration. You can use this procedure if you have forgotten the password to access the device, or

simply wish to return the unit to its default configuration state.

Extension Slots and Ports

MicroSD card slot.

MicroUSB type AB.

1x SFP cage in the combo group with 1x 10/100/1000 Ethernet port (software selectable which one will be active).

7x 10/100/1000 Ethernet ports.

RS232 serial console port (115200bit/s, 8 data bits, 1 stop bit, no parity).

1x SFP+ cage.

Two cooling fans.

Smart card slot.

Configuration

Once logged in, we recommend clicking the "Check for updates" button in the QuickSet menu, as updating your RouterOS software to the latest version

ensures the best performance and stability. For wireless models, please make sure you have selected the country where the device will be used, to

conform with local regulations.

RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to

the possibilities: . In case IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address https://mt.lv/help https://mt.lv/winbox

of the device from the LAN side (all access is blocked from the Internet port by default).

For recovery purposes, it is possible to boot the device for reinstallation, see a section Reset button.

Reset button

The RouterBOOT reset button has the following functions. Press the button and apply the power, then:

Release the button when the green LED starts flashing, to reset RouterOS configuration to defaults.

Release the button when the LED turns solid green to clear all configuration and defaults.

Release the button after LED is no longer lit (~20 seconds) to cause the device to look for Netinstall servers (required for reinstalling RouterOS

over the network).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.

Useful for RouterBOOT debugging and recovery.

Accessories

Package includes the following accessories that come with the device:

Two EU/US AC power cords, D03+QT3 H05VV-F 3x0.75 mm 2 1.83 m RoHS.

Fastening set for rackmount case K-10.

Two Rackmount Case Side Brackets.

USB A Female to Micro B cable.

Please visit wiki pages for MikroTik SFP module compatibility table: https://wiki.mikrotik.com/wiki/MikroTik_SFP_module_compatibility_table

Specifications

For more information about this product, specification and pictures please visit our web page: https://mikrotik.com/product/CCR1009-7G-1C-1Splus

Operating system support

The device supports RouterOS software version 6. The specific factory-installed version number is indicated in the RouterOS menu /system resource.

Other operating systems have not been tested.

Safety Notice

Electric shock hazard. This equipment is to be serviced by trained personnel only.

Federal Communication Commission Interference Statement

To avoid pollution of the environment, please separate the device from household waste and dispose of it in a safe manner, such as in

designated waste disposal sites. Familiarize yourself with the procedures for the proper transportation of the equipment to the designated

disposal sites in your area.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a commercial installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this

equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.

Innovation, Science and Economic Development Canada

This device complies with Industry Canada's license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d'en compromettre le fonctionnement.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.

CAN ICES-003 (A) / NMB-003 (A)

UKCA Marking

Eurasian Conformity Mark

Информация о дате изготовления устройства указана в конце серийного номера на его наклейке через дробь. Первая цифра означает номер

года (последняя цифра года), две последующие означают номер недели.

Изготовитель: Mikrotikls SIA, Aizkraukles iela 23, Riga, LV-1006, Латвия, . Сделано в Китае, Латвии или Литве. Cм. на [email protected]

упаковке.

Для получения подробных сведений о гарантийном обслуживании обратитесь к продавцу. Информация об импортерах продукции MikroTik в

Российскую Федерацию: https://mikrotik.com/buy/europe/russia

Продукты MikroTik, которые поставляются в Евразийский таможенный союз, оцениваются с учетом соответствующих требований и

помечены знаком EAC, как показано ниже:

Norma Oficial Mexicana

EFICIENCIA ENERGETICA CUMPLE CON LA NOM-029-ENER-2017.

La operacion de este equipo esta sujeta a las siguientes dos condiciones:

Es posible que este equipo o dispositivo no cause interferencia perjudicial y.

Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacion no deseada.

Fabricante: Mikrotikls SIA, Brivibas gatve 214i, Riga, LV-1039, Latvia.

País De Origen: Letonia; Lituania; China (Republica Popular); Estados Unidos De America; Mexico.

Por favor contacte a su distribuidor local para preguntas regionales específicas. La lista de importadores se puede encontrar en nuestra página de inicio –

.https://mikrotik.com/buy/latinamerica/mexico

CE Declaration of Conformity

Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039.

The full text of the EU Declaration of Conformity is available at the following internet address: https://mikrotik.com/products

Information contained here is subject to change. Please visit the product page on

www.mikrotik.com for the most up to date version of this

document.

Andere Handbücher für CCR1009-7G-1C-1S+

Inhaltsverzeichnis

Andere MikroTik Netzwerk-Hardware Handbücher

MikroTik

MikroTik CRS310-1G-5S-4S Plus OUT Bedienungsanleitung

MikroTik

MikroTik Network Controller Bedienungsanleitung

MikroTik

MikroTik LHGGM&EG18-EA Bedienungsanleitung

MikroTik

MikroTik Chateau LTE12 Bedienungsanleitung

MikroTik

MikroTik CCR2004-16G-2S+ Bedienungsanleitung

MikroTik

MikroTik nRAY Series Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 2011U Series Bedienungsanleitung

MikroTik

MikroTik LHG LTE6 Bedienungsanleitung

MikroTik

MikroTik RBwAPG-60ad-A Bedienungsanleitung

MikroTik

MikroTik L009UiGS-2HaxD-IN Bedienungsanleitung

MikroTik

MikroTik RBwAPR-2nD Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 711A-5Hn Bedienungsanleitung

MikroTik

MikroTik LHG 60G Bedienungsanleitung

MikroTik

MikroTik SXTsq Lite5 Bedienungsanleitung

MikroTik

MikroTik CRS112-8G-4S-IN Bedienungsanleitung

MikroTik

MikroTik AP Bedienungsanleitung

MikroTik

MikroTik RouterBOARD SXT G-2HnD Bedienungsanleitung

MikroTik

MikroTik FiberBox Plus Bedienungsanleitung

MikroTik

MikroTik SXT R Bedienungsanleitung

MikroTik

MikroTik Chateau LTE18 ax Bedienungsanleitung

MikroTik

MikroTik wAP R ac Series Bedienungsanleitung

MikroTik

MikroTik C52iG-5HaxD2HaxD-TC Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 750 Bedienungsanleitung

MikroTik

MikroTik RB5009UPr+S+IN Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung