MikroTik Network Controller Bedienungsanleitung

Network Controller Normalization Guide

Viasat Inc. Proprietary & Confidential 1 / 6

Network Controller Normalization Guide

Viasat Community Internet

Revision 1.0 – 2020.12.02

Network Controller Normalization Guide

Viasat Inc. Proprietary & Confidential 2 / 6

Overview

This guide provides instructions on normalizing the MikroTik Network Controller (NC) so

that it can be properly staged.

This process only needs to be implemented if there were errors that prevented

successful staging OR if the SSID for the NC was not visible on the Staging App to

begin with. If there were errors during the staging procedure, the NC will also need to be

factory reset before normalization.

This process can occur any time before leaving for installation – it does not need to

happen immediately before installation.

Connection to Viasat satellite network is NOT required for normalizing or factory

resetting these devices. Furthermore, the Network Controller MUST NOT be connected

to an internet source during normalization.

REQUIRED ITEMS:

•One Mikrotik Network Controller (NC)

•One NC power cord (comes with the device)

•One NC PoE injector (comes with the device)

•A laptop with an ethernet port and Winbox installed

oWinbox can be downloaded at https://mikrotik.com/download (installation

type will depend on whether a 32-bit or 64-bit machine is being used)

oUse this link if you are unsure whether you have a 32 or 64 bit computer.

•Two pre-tested Ethernet cords

•Working power outlet

•Paperclip or other fine-pointed object

NOTE: A different model may be used for the MikroTIK items pictured in this guide, but

the process is identical.

Network Controller (NC)

PoE Injector

Network Controller Normalization Guide

Viasat Inc. Proprietary & Confidential 3 / 6

NC Factory Resetting Instructions:

NOTE: If errors were encountered in the middle of staging that prevented the NC from

being staged successfully, follow the following steps to factory reset before normalizing.

If there was no SSID visible on the staging app to begin with then skip to the “NC

Normalization Instructions” section of this document.

1. Plug the NC power cord into the PoE injector and connect the power cord to a

functioning power outlet.

2. Plug an ethernet cable to the other end of the PoE injector, a light on the injector

indicates successful connection to power. DO NOT CONNECT THE PoE TO A

MODEM OR ANY OTHER INTERNET SOURCE.

3. Perform a Factory Reset on the NC: Hold down the Reset button (circled below)

on the NC.

4. WHILE STILL HOLDING DOWN THE RESET BUTTON, insert the other end of

the ethernet cable connected to the PoE injector into Port 1 of the NC.

Network Controller Normalization Guide

Viasat Inc. Proprietary & Confidential 4 / 6

5. Continue holding down the reset button until the blue power light flashes (this will

happen 5 seconds after the ethernet cable is plugged into the NC).

6. As soon as the power light flashes, release the reset button.

NOTE: The reset button should never be pressed for more than 10 seconds

otherwise another factory reset is required. If the LED turns solid while still

pressingthe reset button then it was held for too long. If this happens, unplug the

ethernet cable and perform another factory reset per the above steps.

NC Normalization Instructions:

Purpose: To normalize WiFi devices that do not match the factory configuration

advertised by MikroTik.

1) To normalize the NC (Controller), first power on the controller by plugging an

ethernet cable from Port 1 of the controller to the PoE injector. Connect the PoE

injector to the NC power cord and a working power outlet. Then connect a second

ethernet cable directly from your laptop to Port 2 (ether2) of the NC.

Port 2

Network Controller Normalization Guide

Viasat Inc. Proprietary & Confidential 5 / 6

2) Open Winbox and inspect the “Neighbors” tab.

NOTE: If the MAC address does not appear in the list, try to select “refresh” a

couple of times – waiting at least 5 seconds between refreshing. Repeat refresh

no more than three times. If the MAC addres does not appear, then manually

enterthe device’s MAC address in the “Connect To” field.

3) Click on the device’s MAC address and select “Connect” to establish a

session with the device. Leave the username as “admin” and password blank.

4) On the left pane, select “New Terminal”.

5) Copy and paste the following command into the command prompt and press

the “Enter” key:

/system reset-configuration no-defaults=yes caps-mode=no

6) When prompted with the below warning, type in “y” (without quotation marks)

and press the “Enter” key.

7) Wait for the device to reboot, which can take up to three minutes. Once the

device reappears on Winbox, click “reconnect”.

8) Download the zip file (“Command File”) underneath the webpage title on the

eguide or at this link.

Network Controller Normalization Guide

Viasat Inc. Proprietary & Confidential 6 / 6

9) Open the downloaded zip and save the file locally (for instance on your

desktop) on the computer being used to interface with routerOS.

NOTE: there can be no changes to the name of this file otherwise the

normalization process will fail. Verify that the files were saved to your computer

with the exact filename “InstallDefaultsOmnitik.rsc”.

NOTE: these files must be unzipped before proceeding into the“.rsc” file. If you

cannot open the zip, download a program such as 7-Zip to do so.

10)Once the files are saved, return to the Winbox application and select “Files”

on the left-hand pane:

11)Select “Upload” then find and click on the saved file on your computer titled,

“InstallDefaultsOmnitik.rsc”.

12)Click on “New Terminal”.

13) Copy and paste the command shown below into the terminal and press

“Enter”.

/import InstallDefaultsOmnitik.rsc

WInbox willreturn a successful output, similar to the following:

The Normalization process is now complete.

NOTE: Now that normalization is complete, these devices SHOULD NOT be

factory reset again. If the device is subject to a factory reset, it must be

normalized once more.

NOTE: These devices still need to be staged before use in an install.

Inhaltsverzeichnis

Andere MikroTik Netzwerk-Hardware Handbücher

MikroTik

MikroTik LHG 60G Bedienungsanleitung

MikroTik

MikroTik Woobm-USB Bedienungsanleitung

MikroTik

MikroTik 2004-1G-12S+2XS Bedienungsanleitung

MikroTik

MikroTik RouterBOARD Groove 2Hn Bedienungsanleitung

MikroTik

MikroTik CRS310-1G-5S-4S+IN Bedienungsanleitung

MikroTik

MikroTik SXTsq Lite5 Bedienungsanleitung

MikroTik

MikroTik RBLDF-5nD Bedienungsanleitung

MikroTik

MikroTik hAP ax lite LTE6 Bedienungsanleitung

MikroTik

MikroTik LHG LTE18 kit Bedienungsanleitung

MikroTik

MikroTik RAY60 Bedienungsanleitung

MikroTik

MikroTik Metal 52 ac Bedienungsanleitung

MikroTik

MikroTik RBMetalG-52SHPacn Bedienungsanleitung

MikroTik

MikroTik RouterBOARD 800 Series Bedienungsanleitung

MikroTik

MikroTik cAP ax Bedienungsanleitung

MikroTik

MikroTik LHG 60G Bedienungsanleitung

MikroTik

MikroTik CRS518-16XS-2XQ-RM Bedienungsanleitung

MikroTik

MikroTik CRS112-8G-4S-IN Bedienungsanleitung

MikroTik

MikroTik RBwAPG-60ad-A Bedienungsanleitung

MikroTik

MikroTik RBM11G Bedienungsanleitung

MikroTik

MikroTik wAP R ac Series Bedienungsanleitung

MikroTik

MikroTik Chateau LTE12 Bedienungsanleitung

MikroTik

MikroTik CCR2004-16G-2S+ Bedienungsanleitung

MikroTik

MikroTik nRAY Series Bedienungsanleitung

MikroTik

MikroTik PL7411-2nD Kurzanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung