Miller Century 5230 Bedienungsanleitung

CENTURY®

L E G E N D A R Y L E A D E R S H I P

OWNER'S MANUAL

5130 / 5230

INSTALLATION, OPERATION, MAINTENANCE & PARTS

NOTE: MANUAL including SPECIFICATIONS, subject to change without notice

All ratings specified are based on structural factors only,

not vehicle capacities or capabilities.

CENTURY®

Miller Industries Towing Equipment Inc.

8503 Hilltop Drive

Ooltewah, Tennessee 37363 FORM NO. 0501140

08 / 01

Phone (423) 238-4171 • FAX (423) 238-5371 PRICE $25.00

LIMITED WARRANTY

MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the

original purchaser that each new MILLER wrecker or other MILLER products will be free from defects in

material and workmanship for a period of twelve (12) months from date placed in service, but in no event

shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER. The

purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no event

shall MILLER accept such notification later than twenty-four (24) months from date of delivery or twelve

(12) months from date placed in service, whichever is earlier.

MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement at

the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon

inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will be

used for any replacement at MILLER's option. This warranty is not transferable. This warranty does not

obligate MILLER to bear the cost of labor or transportation charges in connection with the repair or

replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or

alterations have been made unless authorized by MILLER.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER

WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime,

claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential damages

concerning or relating to any product or parts, whether based on negligence, strict liability, breach of

contract, breach of warranty, misrepresentation or any other legal theory, regardless of whether the loss

resulted from any general or particular requirement which MILLER knew or had reason to know about at

the time of sale.

MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS

MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO

PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or any

accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR

PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such

warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted

under applicable law, pass on to the purchaser such manufacturer's or seller's warranty.

MILLER, whose policy is one of continuous improvement, reserves the right to improve its products

through changes in design or materials as it may deem desirable without being obligated to incorporate

such changes in products previously sold. This warranty is not intended to cover or include the following

items, which are set forth by way of example and not limitation:

A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to

weather, road conditions, road treatments, etc.

B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure

to provide reasonable and necessary maintenance, or uses for which the equipment was not

designed or intended.

C. Alterations or modifications that affect performance, operation or reliability.

D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud

flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.

IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER

PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY

OTHER IMPROPER USE.

SERIAL NUMBER

Miller Industries Towing Equipment Inc.

8503 Hilltop Drive

Ooltewah, Tennessee 37363

Telephone (423) 238-4171

Section VI - PARTS

This Section is provided by the manufacturer for the purpose of ordering

any component part of the CENTURY 5130 or 5230 that may be required

when part replacement is necessary. Be certain to use only original equipment

replacement parts for warranty purposes as well as for keeping your

CENTURY 5130 or 5230 in its original state and optimum operating

capacities. When ordering replacement or spare parts be sure to provide

the following information to the manufacturer’s Parts Department.

1. Manual Number & Date of Publication

2. Manual Page Number

3. Page Title

4. Reference Number of Part Desired

5. Part Number

6. Part Description

7. Quantity of Part Desired

Providing this information will help ensure that the correct parts will be

delivered to you in an expedient manner. Should additional information be

required for repair or replacement of certain components, contact your

Manufacturer Authorized Representative.

The Manufacturer reserves the right, without notice or obligation, to improve

or modify their products, which may change the specifications, models and

feature availability.

VI-1

VI-2

Section VI - PARTS (cont'd)

SUBFRAME ASSEMBLY

VI-3

REF. NO. PART

NO. REQ'D NUMBER DESCRIPTION

Section VI - PARTS (cont'd)

SUBFRAME ASSEMBLY

1 6 0300113 GREASE FITTING

2 2 0301861 QUICK PIN

3 2 0302538 BUSHING, 3-1/2" X 2-1/2" INTERNAL

4 8 0302540 CENTER BONDED MOUNT

5 12 0302541 SPECIAL WASHER

6 2 0303140 RAMP PAD

7 2 0303445 SAFETY CHAIN, SYSTEM 10

8 REF. 0306647 SPADE CYLINDER

9 REF. 0307012 LIFT CYLINDER

10 8 0400066 SCREW, 1/4"-20 X 3/4" HEX HD CAP

11 10 0400128 SCREW, 3/8"-16 X 1-1/4" FL HD SKT

12 4 0400139 SCREW, 3/8"-16 X 1-1/2" HEX SKT SET

13 10 0400181 SCREW, 1/2"-13 X 1-1/2" HEX HD CAP

14 2 0400219 SCREW, 1/2"-13 X 4-1/2" HEX HD CAP

15 2 0400260 SCREW, 5/8"-11 X 2" HEX HD CAP

16 4 0400276 SCREW, 5/8"-11 X 4-1/2" HEX HD CAP

17 4 0400281 SCREW, 3/4"-10 X 3-1/2" HEX HD CAP

18 12 0400288 SCREW, 3/4"-10 X 2-1/2" HEX HD CAP

19 4 0400294 SCREW, 3/4"-10 X 6-1/2" HEX HD CAP

20 23 0400392 NUT, 3/8"-16 NYLOK HEX

21 2 0400408 NUT, 1/2"-13 NYLOK HEX

22 2 0400421 NUT, 5/8"-11 NYLOK HEX

23 4 0400430 NUT, 3/4"-10 NYLOK HEX

24 12 0400431 NUT, 3/4"-10 NYLOK HEX

25 8 0400452 LOCKWASHER, 1/4" HELICAL

26 10 0400506 WASHER, 5/8" FLAT

27 4 0400508 LOCKWASHER, 5/8" HELICAL

28 8 0400510 WASHER, 3/4" FLAT (5230)

29 2 9046354 SPRING PIN, 1/4" X 2-1/2"

30 2 0705485 SPADE BLADE

31 2 0705500 SHAFT, LOWER SPADE

32 2 0707118 PIN, LIFT CYLINDER

33 2 0707394 SHAFT, UPPER SPADE

34 4 0714581 BOLTING PLATE

35 2 0715694 PIN, SPADE PIVOT

36 2 0715796 COVER PLATE, SPADE

37 1 0802211 FRONT BODY MTG TUBE (5130)

-- 1 0802868 FRONT BODY MTG TUBE WELDMENT (5230)

38 2 0802219 PIVOT PIN, LIFT CYLINDER

39 2 0804286 LOWER SPADE PAD WELDMENT

40 2 0804334 PIN, MULTI-POSITION

41 1 0804360 LEFT INNER SPADE WELDMENT

42 1 0804361 RIGHT INNER SPADE WELDMENT

43 2 0804405 BRACKET, BOOM PIVOT

44 1 0805899 SUBFRAME WELDMENT

VI-4

Section VI - PARTS (cont'd)

STANDARD BODY ASSEMBLY - 5130

VI-5

REF. NO. PART

NO. REQ'D NUMBER DESCRIPTION

REF. NO. PART

NO. REQ'D NUMBER DESCRIPTION

Section VI - PARTS (cont'd)

STANDARD BODY ASSEMBLY - 5130

1 14 FT. 0300345 RUBBER FENDER

2 2 0301223 MUDFLAP

3 6 0301912 DOOR CHECK, 11"

4 7 FT. 0303056 "D" GASKET (NOT SHOWN)

5 1 0303061 BACKUP ALARM (NOT SHOWN)

6 1 0306834 TOOL BOX, 156" C.A. LT STEEL SINGLE

7 1 0306835 TOOL BOX, 156" C.A. RT STEEL SINGLE

8 6 0400005 SCREW, #6-32 X 1/2" RD HD PH

9 6 0400061 SCREW, 1/4"-20 X 3/4" MACH

10 6 0400066 SCREW, 1/4"-20 X 3/4" HEX HD CAP

11 8 0400101 SCREW, 5/16"-18 X 1" RD HD MACH

12 8 0400122 SCREW, 3/8"-16 X 1-1/4" HEX HD CAP

13 3 0400367 NUT, 1/4"-20 NYLOK HEX

14 6 0400369 CLIP, 1/4" TINNERMAN

15 8 0400392 NUT, 3/8"-16 NYLOK HEX

16 6 0400451 WASHER, 1/4" FLAT

17 40 0400566 RIVET, 1/4"

18 6 0402094 NUT, #6-32 HEX

19 1 0705090 MUDFLAP MTG ANGLE, LEFT

20 1 0705091 MUDFLAP MTG ANGLE, RIGHT

21 2 0705092 BAR, MUDFLAP

22 2 0706609 RETAINING STRIP, RUBBER FENDER

23 1 0711289 PANEL, SWITCH

24 1 0711290 PANEL, CONTROL

25 1 0711292 PANEL, CONTROL

26 1 0711344 PANEL, GAUGE

27 4 0713171 SPACER PLATE, STEEL (NOT SHOWN)

28 2 0714176 GASKET, BASE ANGLE (NOT SHOWN)

29 2 0714177 GASKET (NOT SHOWN)

30 1 0901496 CENTURY NAMEPLATE KIT

-- 6 0400035 SCREW, #10-24 X 1/2" OVAL HD SS

-- 2 0500406 CENTURY NAMEPLATE

31 -- 0902328 BODY MOUNTING KIT (NOT SHOWN)

-- 2 0707174 ANGLE, TAILGATE MOUNTING

-- 2 0707175 MOUNTING PLATE

-- 2 0711256 MOUNTING PLATE

-- 2 0711286 SPACER, REAR FRAME BRACKET

32 -- 0904217 BODY MOUNTING HARDWARE (NOT SHOWN)

-- 34 0400288 SCREW, 3/4"-10 X 2-1/2" HEX HD CAP

-- 4 0400303 SCREW, 7/8"-9 X 2-1/2" HEX HD CAP

-- 34 0400431 NUT, 3/4"-10 NYLOK HEX

-- 4 0400436 NUT, 7/8"-9 NYLOK HEX

33 -- 0907043 KIT, TOOL BOX HOLE PLUG (NOT SHOWN)

-- 8 0307052 RUBBER WASHER

-- 4 0400201 SCREW, 1/2"-13 X 1-1/2" CRGBLT

-- 4 0400407 NUT, 1/2"-13 HEX

-- 4 0400491 LOCKWASHER, 1/2" HELICAL

-- 4 0400492 WASHER, 1/2" FLAT

-- 4 0400506 WASHER, 5/8" FLAT

-- -- 124001720 LIGHT BAR, STANDARD

34 2 0301706 GASKET, LIGHT BAR

35 4 0400126 SCREW, 3/8"-16 X 1" HEX HD CAP

36 12 0400177 SCREW, 1/2"-13 X 1-1/4" HEX HD CAP

37 6 0400181 SCREW, 1/2"-13 X 1-1/2" HEX HD CAP

38 4 0400392 NUT, 3/8"-16 NYLOK HEX

39 18 0400408 NUT, 1/2"-13 NYLOK HEX

40 12 0400492 WASHER, 1/2" FLAT

41 1 0802224 SUPPORT, L.H. VERTICAL

42 1 0802225 SUPPORT, R.H. VERTICAL

43 2 0802226 MOUNTING BRACKET

44 1 0802260 TOP CHANNEL

-- -- 124001708 AERODYNAMIC LIGHT PYLON

45 1 0302562 LIGHT RACK

46 6 0400157 SCREW, 3/8"-16 X 1-3/4" HEX HD CAP

47 6 0400392 NUT, 3/8"-16 NYLOK HEX

48 6 0400480 WASHER, 3/8" FLAT

49 2 0706972 LIGHT PYLON, MOUNTING RUBBER

VI-6

Section VI - PARTS (cont'd)

STANDARD BODY ASSEMBLY - 5230

VI-7

REF. NO. PART

NO. REQ'D NUMBER DESCRIPTION

REF. NO. PART

NO. REQ'D NUMBER DESCRIPTION

Section VI - PARTS (cont'd)

STANDARD BODY ASSEMBLY - 5230

1 28 FT. 0300345 RUBBER FENDER

2 2 0301223 MUDFLAP

3 6 0301912 DOOR CHECK, 11"

4 7 FT. 0303056 "D" GASKET (NOT SHOWN)

5 1 0303061 BACKUP ALARM (NOT SHOWN)

6 113 FT. 0306553 DOOR SEAL (NOT SHOWN)

7 1 0306790 TOOL BOX, 156" C.B. LT ALUM TANDEM

8 1 0306791 TOOL BOX, 156" C.B. RT ALUM TANDEM

9 6 0400005 SCREW, #6-32 X 1/2" RD HD PH

10 6 0400061 SCREW, 1/4"-20 X 3/4" MACH

11 6 0400066 SCREW, 1/4"-20 X 3/4" HEX HD CAP

12 8 0400101 SCREW, 5/16"-18 X 1" RD HD MACH

13 8 0400122 SCREW, 3/8"-16 X 1-1/4" HEX HD CAP

14 3 0400367 NUT, 1/4"-20 NYLOK HEX

15 6 0400369 CLIP, 1/4" TINNERMAN

16 8 0400392 NUT, 3/8"-16 NYLOK HEX

17 6 0400451 WASHER, 1/4" FLAT

18 76 0400566 RIVET, 1/4"

19 6 0402094 NUT, #6-32 HEX

20 1 0708809 MUDFLAP MTG ANGLE, RT

21 1 0708810 MUDFLAP MTG ANGLE, LT

22 2 0705092 BAR, MUDFLAP

23 4 0706609 RETAINING STRIP, RUBBER FENDER

24 1 0711289 PANEL, SWITCH

25 1 0711290 PANEL, CONTROL

26 1 0711292 PANEL, CONTROL

27 1 0711344 PANEL, GAUGE

28 2 0710502 MOUNTING PLATE (NOT SHOWN)

29 4 0713170 SPACER PLATE, ALUMINUM (NOT SHOWN)

30 2 0714176 GASKET, BASE ANGLE (NOT SHOWN)

31 2 0714177 GASKET (NOT SHOWN)

32 1 0803036 CROSSMEMBER, ALUMINUM BODY

(NOT SHOWN)

33 1 0901496 CENTURY NAMEPLATE KIT

-- 6 0400035 SCREW, #10-24 X 1/2" OVAL HD SS

-- 2 0500406 CENTURY NAMEPLATE

34 -- 0902328 BODY MOUNTING KIT (NOT SHOWN)

-- 2 0707174 ANGLE, TAILGATE MOUNTING

-- 2 0707175 MOUNTING PLATE

-- 2 0711256 MOUNTING PLATE

-- 2 0711286 SPACER, REAR FRAME BRACKET

35 -- 0904217 BODY MOUNTING HARDWARE (NOT SHOWN)

-- 34 0400288 SCREW, 3/4"-10 X 2-1/2" HEX HD CAP

-- 4 0400303 SCREW, 7/8"-9 X 2-1/2" HEX HD CAP

-- 34 0400431 NUT, 3/4"-10 NYLOK HEX

-- 4 0400436 NUT, 7/8"-9 NYLOK HEX

36 -- 0904353 CHAIN RACK, ALUMINUM BODY (NOT SHOWN)

-- 3 0400133 SCREW, 3/8"-16 X 3" HEX HD CAP

-- 3 0400392 NUT, 3/8"-16 NYLOK HEX

-- 1 0803768 CHAIN HANGER WELDMENT

37 -- 0906256 TRAY KIT (NOT SHOWN)

-- 3 0400105 SCREW, 5/16"-18 X 1-1/4" SELF TAP

-- 2 0400133 SCREW, 3/8"-16 X 3" HEX HD CAP

-- 2 0400392 NUT, 3/8"-16 NYLOK HEX

-- 2 0400480 WASHER, 3/8" FLAT

-- 1 0804229 TRAY WELDMENT

38 -- 0907043 KIT, TOOL BOX HOLE PLUG (NOT SHOWN)

-- 8 0307052 RUBBER WASHER

-- 4 0400201 SCREW, 1/2"-13 X 1-1/2" CRGBLT

-- 4 0400407 NUT, 1/2"-13 HEX

-- 4 0400491 LOCKWASHER, 1/2" HELICAL

-- 4 0400492 WASHER, 1/2" FLAT

-- 4 0400506 WASHER, 5/8" FLAT

39 -- 124001720 LIGHT BAR, STANDARD

(REFER TO PAGE VI-4 & VI-5)

40 -- 124001708 AERODYNAMIC LIGHT PYLON

(REFER TO PAGE VI-4 & VI-5)

VI-8

Section VI - PARTS (cont'd)

RECOVERY BOOM ASSEMBLY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Miller Autozubehör Handbücher

Miller

Miller Millermatic 211 Auto-Set Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung