Milwaukee MC125 Bedienungsanleitung

SPECIFICATIONS :

pH ORP

RANGE 0.00 to 14.00 ±1000 mV

RESOLUTION 0.01 1 mV

ACCURACY (@25°C) ±0.2 ± 5 mV

SETPOINT 4 to 8 pH -200 to 600 mV

ELECTRODE (included) MA911B/2 MA921B/2

ALARM & active when measurement is

OUTPUT POWER SOCKET higher/lower than the setpoint

depending on user selection

ENVIRONMENT 0 to 50°C, 95% RH max.

POWER SUPPLY 12 VDC (included)

POWER DRIVERS 115VAC, 2A, 60Hz or 230VAC, 1A, 50Hz

DIMENSIONS 148.5 x 82.5 x 32 mm

WEIGHT 200 g meter only

OPTIONAL ACCESSORIES:

M10004B pH 4.01 buffer solution 20 ml sachet (25 pcs)

M10007B pH 7.01 buffer solution 20 ml sachet (25 pcs)

M10010B pH 10.01 buffer solution 20 ml sachet (25 pcs)

M10000B Electrode rinse solution 20 ml sachet (25 pcs)

MA9015 Electrode storage solution 20 ml sachet (25 pcs)

WARRANTY:

This instrument is warranted from all defects in materials and manufacturing

for a period of two years from the date of purchase.

The electrodes are warranted for a period of 6 months.

If during this period, repair or replacement of parts is required, where the

damage is not due to negligence or erroneous operation by the user, please

return the parts to either dealer or our office and the repair will be effected

free of charge.

Note: We reserve the right to modify the design, construction and

appearance of our products without advance notice.

USER MANUAL

PORTABLE

pH I ORP COMBINED METER

MODEL: MC125

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

OPERATION:

•Connect the supplied 12 VDC

power adapter to the meter and

to the mains line.

•Connect the pH and ORP elec-

trode to the BNC socket of the

meter.

•Always remove the electrode

protective caps before taking any

measurement. If the electrodes

have been left dry, soak the tip

(bottom 2.5 cm) in rinse solution

(M10000B) for a few minutes to reactivate them.

•Make sure that the meter has been calibrated before taking any

measurements (see Calibration Procedure).

•Immerse the tip (2.5 cm) of the electrodes into the samples.

•Turn the instrument on by pressing the ON/OFF key.

•Allow the reading to stabilize and the meter will start continuous

monitoring.

•A blinking alarm LED will indicate when the measured pH value is

higher or lower than the setpoint depending on user selection.

•When the alarm LED is blinking, there is power in the output power

socket.

NOTE: The output power contact has no protection fuse inside the

meter. It is recommended to protected it outside, against failure.

SETPOINT:

•The setpoint can be selected by adjusting the knob to the desired

value.

•The selectable range for MC125 is from

4 to 8 for pH and from -200 to 600 mV

for ORP.

•The nature of the setpoint can be se-

lected by setting the proper switch to the

desired position (ABOVE or BELOW).

CALIBRATION PROCEDURE:

•Remove the protective cap from the pH electrode.

•Immerse the electrode tip into a new sachet of pH 7

calibration solution and allow the reading to stabilize.

•Adjust the pH7 calibration trimmer (on the front) to

display "7.00 pH".

•Open a new sachet of pH 4 calibration solution and

use a small quantity to rinse the electrode.

•Immerse the electrode tip inside the pH 4 sachet and

allow the reading to stabilize.

•Adjust the pH4/10 calibration trimmer (on the front) to

display "4.00 pH".

•The calibration is now complete and the meter is ready

to take measurements.

•It is suggested to recalibrate the meter at least

once a month, after prolonged warehousing time

and after pH electrode replacement.

INSTALLATION PROCEDURE:

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

Andere Milwaukee Messgerät Handbücher

Milwaukee

Milwaukee MI404 Bedienungsanleitung

Milwaukee

Milwaukee Mi451 Bedienungsanleitung

Milwaukee

Milwaukee MW605 MAX Bedienungsanleitung

Milwaukee

Milwaukee M12 3PLA Bedienungsanleitung

Milwaukee

Milwaukee 2309-60 Bedienungsanleitung

Milwaukee

Milwaukee MW102 Bedienungsanleitung

Milwaukee

Milwaukee MW801 Bedienungsanleitung

Milwaukee

Milwaukee MW190 MAX Bedienungsanleitung

Milwaukee

Milwaukee M12 ICAV3 Bedienungsanleitung

Milwaukee

Milwaukee M12 SUB-SCANNER 2291-20 Bedienungsanleitung

Milwaukee

Milwaukee MI405 Bedienungsanleitung

Milwaukee

Milwaukee MA881 Bedienungsanleitung

Milwaukee

Milwaukee 2212-20 Bedienungsanleitung

Milwaukee

Milwaukee LDM 30 Bedienungsanleitung

Milwaukee

Milwaukee pH52 Bedienungsanleitung

Milwaukee

Milwaukee 2231-20 Bedienungsanleitung

Milwaukee

Milwaukee pH 58 Bedienungsanleitung

Milwaukee

Milwaukee Smart Monitoring System SMS110 Bedienungsanleitung

Milwaukee

Milwaukee MW190 Bedienungsanleitung

Milwaukee

Milwaukee MW102 Bedienungsanleitung

Milwaukee

Milwaukee L4 CLL Bedienungsanleitung

Milwaukee

Milwaukee MW13 Bedienungsanleitung

Milwaukee

Milwaukee LDM 45 Bedienungsanleitung

Milwaukee

Milwaukee 4933478101 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung