Milwaukee MW500 Bedienungsanleitung

USER MANUAL

PORTABLE

ORP METER

MODEL: MW500

Smart ORP Meter

ISTMW500 01/10

SPECIFICATIONS:

MW500

RANGE ±1000 mV

RESOLUTION 1 mV

ACCURACY (@25°C) ±5 mV

TYPICAL EMC DEVIATION ±5 mV

ORP ELECTRODE MA921B/1 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

BATTERY TYPE 9V alkaline (included)

BATTERY LIFE approximately 300 hours of use

DIMENSIONS 143 x 80 x 32 mm

WEIGHT 220 g (with battery) meter only

OPTIONAL ACCESSORIES:

M10000B Electrode rinse solution, 20 mL sachet (25 pcs)

MA9015 Electrode storage solution, 220 mL bottle

MA9020 200-275 mV ORP solution, 220 mL bottle

MA921B/1 Platinum ORP electrode with 1 m cable

WARRANTY:

This instrument is warranted from all defects in materials and manufacturing

for a period of two years from the date of purchase.

The electrode is warranted for a period of six months.

If during this period, the repair or replacement of parts is required, where the

damage is not due to negligence or erroneous operation by the user, please

return the parts to either dealer or our office and the repair will be effected

free of charge.

Note: We reserve the right to modify the design, construction and appearance

of our products without advance notice.

Milwaukee

OPERATION:

• The meter is supplied complete with a 9V battery. Slide off

the battery compartment cover located on the back of the

meter. Install the battery into the battery clip connector

while observing polarity.

• Always remove the electrode protective cap before taking

any measurement. If the electrode has been left dry, soak

the tip in storage solution for a few minutes to reactivate it.

• Connect the ORP electrode to the BNC socket on the top

of the meter.

• Immerse the tip (2.5 cm) of

the ORP electrode into the

sample.

• Turn the instrument on by

pressing the ON/OFF key.

• Allow the reading to stabilize

before taking measurements.

• After use, switch the meter

off and store the electrode

with a few drops of storage

solution in the protective

cap.

• The meter is factory

calibrated. ORP electrodes

are interchangeable and no

mV calibration is needed

when they are replaced.

MAINTENANCE:

• The surface of the ORP electrode must always be clean.

Use M10000B rinse solution for this purpose. If needed,

clean the Platinum tip with very fine abrasive paper.

• When not in use, the tip (reference junction) of the electrode

should always be kept moist and safe from any mechanical

stress.

BATTERY REPLACEMENT:

When the battery becomes weak the meter will display " ",

the low battery indicator. The battery has about 50 hours of working

time left. A low battery will result in unreliable measurements.

Prompt battery replacement is required.

Battery replacement must only take place in a non hazardous

area using an alkaline 9V battery.

Turn the meter off, slide the battery compartment cover located

at the rear of the meter off and replace the 9V battery with a

new one. Make sure the battery contacts are fully engaged in

the connector, seat the battery in its compartment and replace

the cover.

Andere Milwaukee Messgerät Handbücher

Milwaukee

Milwaukee C12 CMH Bedienungsanleitung

Milwaukee

Milwaukee 2236-20 Bedienungsanleitung

Milwaukee

Milwaukee PH55 Bedienungsanleitung

Milwaukee

Milwaukee MW105 MAX Bedienungsanleitung

Milwaukee

Milwaukee 48-22-9802 Bedienungsanleitung

Milwaukee

Milwaukee EC40 Bedienungsanleitung

Milwaukee

Milwaukee MI 413 Bedienungsanleitung

Milwaukee

Milwaukee 2010R Bedienungsanleitung

Milwaukee

Milwaukee MW10 Bedienungsanleitung

Milwaukee

Milwaukee CALIBRATION 2238-20 Betriebsanleitung

Milwaukee

Milwaukee 2205-40 Bedienungsanleitung

Milwaukee

Milwaukee L4 CLL Bedienungsanleitung

Milwaukee

Milwaukee MW14 Bedienungsanleitung

Milwaukee

Milwaukee C65 Bedienungsanleitung

Milwaukee

Milwaukee SM101 Bedienungsanleitung

Milwaukee

Milwaukee MW700 Bedienungsanleitung

Milwaukee

Milwaukee MI805 Bedienungsanleitung

Milwaukee

Milwaukee pH51 Bedienungsanleitung

Milwaukee

Milwaukee SM106 Bedienungsanleitung

Milwaukee

Milwaukee 2205-20 Bedienungsanleitung

Milwaukee

Milwaukee 2235-20 Bedienungsanleitung

Milwaukee

Milwaukee MI 411 Bedienungsanleitung

Milwaukee

Milwaukee MI411 Bedienungsanleitung

Milwaukee

Milwaukee MC730 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung