Milwaukee SM500 Bedienungsanleitung

Milwaukee

USER MANUAL

PORTABLE

ORP METER

MODEL: SM500

Smart ORP Meter

ISMIL500 11/01

SPECIFICATIONS:

SM500

RANGE ±1000 mV

RESOLUTION 1 mV

ACCURACY (@25°C) ±5 mV

ORP ELECTRODE MA921B/1 (included)

ENVIRONMENT 0 to 50°C, 95% RH max.

BATTERY TYPE 9V alkaline (included)

BATTERY LIFE approximately 300 hours of use

DIMENSIONS 145 x 80 x 40 mm

WEIGHT 220 g (with battery) meter only

OPTIONAL ACCESSORIES:

M10000B Electrode rinse solution, 20 ml sachet (25 pcs)

MA9015 Electrode storage solution, 220 ml bottle

MA9020 200-275 mV ORP solution, 220 ml bottle

MA921B/1 Platinum ORP electrode with 1 m cable

WARRANTY:

This instrument is warranted from all defects in materials and

manufacturing for a period of two years from the date of purchase.

The electrode is warranted for a period of 6 months.

If during this period, the repair or replacement of parts is required,

where the damage is not due to negligence or erroneous operation

by the user, please return the parts to either dealer or our office

and the repair will be effected free of charge.

Note: We reserve the right to modify the design, construction and

appearance of our products without advance notice.

Milwaukee

OPERATION:

• The meter is supplied complete with a 9V battery. Slide off

the battery compartment cover on the back of the meter.

Install the battery while paying attention to its polarity.

• Always remove the electrode protective cap before taking

any measurement. If the electrode has been left dry, soak

the tip in storage solution for a few

minutes to reactivate it.

• Connect the ORP electrode to the

BNC socket on the top of the meter.

• Immerse the tip (2.5 cm) of the ORP

electrode into the sample.

• Turn the instrument on by pressing

the ON/OFF key.

• Allow the reading to stabilize before

taking measurements.

• After use, switch the meter off and

store the electrode with a few drops

of storage solution in the protective

cap.

• The meter is factory calibrated. ORP

electrodes are inter-changeable and

no mV calibration is needed when

they are replaced.

MAINTENANCE:

• To correctly perfom a redox measurement, the surface of

the ORP electrode must always be clean. Use for this

purpose the M10000B rinse solution. If needed, brush the

Platinum tip with very fine abrasive paper.

• When not in use, the tip of the electrode should always be

kept moist and safe from any mechanical stress.

BATTERY REPLACEMENT:

When the battery becomes weak the meter will display "S".

When the low battery indicator appears, the battery has only

about 50 hours of working time left. A low battery will result in

unreliable measurements. It is recommended to replace the

battery immediately.

Battery replacement must only take place in a non hazardous

area using an alkaline 9V battery.

Turn the meter off, slide off the battery compartment cover at

the rear of the meter and replace the 9V battery with a new

one. Make sure the battery contacts are tight and secure, seat

the battery in its compartment and insert the cover again.

Andere Milwaukee Messgerät Handbücher

Milwaukee

Milwaukee 2205-40 Bedienungsanleitung

Milwaukee

Milwaukee REDLITHIUM L4 3PL Bedienungsanleitung

Milwaukee

Milwaukee Smart PH Meter Bedienungsanleitung

Milwaukee

Milwaukee M12 CLLP Bedienungsanleitung

Milwaukee

Milwaukee 2217-40 Bedienungsanleitung

Milwaukee

Milwaukee 3712 Bedienungsanleitung

Milwaukee

Milwaukee MI407 Bedienungsanleitung

Milwaukee

Milwaukee MW13 Bedienungsanleitung

Milwaukee

Milwaukee PH55 Bedienungsanleitung

Milwaukee

Milwaukee MW806 MAX Bedienungsanleitung

Milwaukee

Milwaukee M12 3PL Bedienungsanleitung

Milwaukee

Milwaukee 2270-20 Bedienungsanleitung

Milwaukee

Milwaukee pH52 Bedienungsanleitung

Milwaukee

Milwaukee MI490 Bedienungsanleitung

Milwaukee

Milwaukee MI405 Bedienungsanleitung

Milwaukee

Milwaukee MA882 Bedienungsanleitung

Milwaukee

Milwaukee MW12 Bedienungsanleitung

Milwaukee

Milwaukee MW801 Bedienungsanleitung

Milwaukee

Milwaukee REDLITHIUM L4 CLL, REDLITHIUM L4 CPL Bedienungsanleitung

Milwaukee

Milwaukee SM700 Bedienungsanleitung

Milwaukee

Milwaukee MA888 Bedienungsanleitung

Milwaukee

Milwaukee MI 404 Bedienungsanleitung

Milwaukee

Milwaukee ORP 57 Bedienungsanleitung

Milwaukee

Milwaukee MA886 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung