MIMAKI JFX 200-2513 Handbuch

Make sure to wear the attached

goggles and glove when you work.

JFX200-2513 / JFX500-2131

Cleaning procedure of head nozzle

Only when the nozzle drop out doesn’t recover with cleaning, daily care and maintenance, please clean

the head nozzle following the procedure below.

Procedure

1. Remove the left side cover of

the machine.

Remove the screw and remove the

cover.

2. Move the carriage(head) to the maintenance space.

(1) Press the key in LOCAL.

(2) Press the key.

(3) Press to select [HEAD MAINT.].

(4) Press the key.

•

Before performing the maintenance, please make sure to attend the training by our engineers. Maintenance

without training may cause failure of the head.

• During maintenance, never rub the nozzles of the head. If rub the nozzle part, the water-repellent surface is

degraded and the head might need to be replaced.

Supply goods for cleaning

Nozzle swab (100) Cleaning stick (50) F200/LF200 Cleaning liquid

for maintenance (100mℓ)

No.SPC-0421 No.SPC-0527 No.SPC-0568

• Make sure to use designated supply goods for nozzle cleaning. Other cleaning goods may cause early

deterioration of the head.

• Head will move for maintenance, please be careful.

[JFX200] Remove the screws

at two positions.

[JFX500] Remove the screws

at four positions.

Cover

Cover

MAINT.

© 2016 MIMAKI ENGINEERING CO., LTD. M018365-00(D203018-10)-15042016

3. Wet a new “nozzle swab” or “clean stick” with the cleaning

solution.

Please wet enough the cleaning solution.

4. Clean the nozzle surface.

(1) Press the "nozzle swab" or "cleaning stick", absorbing cleaning liquid,

against nozzle surface softly for about 10 seconds.

(2) Perform the work (1) to the entire nozzle surface.

5. Press the key after the cleaning.

After initial operation, carriage (head) return to the original position.

Please close the cover.

6. Implement the cleaning [NORMAL].

Please operate with reference to Chapter 4 of the Operation Manual.

7. Perform test printing and check the print result.

Repeat the cleaning and test printing until the result becomes normal.

• Please do not reuse the used clean stick.

It may cause nozzle clogging.

• Please do not rub the nozzle surface and press down strongly

sponge part with your fingers. Nozzle surface is damaged, and it

may cause the discharging defects.

• Please do not re-use the clean stick which was used once. Always

use a new clean stick seconds.

Press softly for 10 seconds

Nozzle surface

KT

Andere Handbücher für JFX 200-2513

5

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere MIMAKI Plotter Handbücher

MIMAKI

MIMAKI DS-1600 Bedienungsanleitung

MIMAKI

MIMAKI APC-130 Bedienungsanleitung

MIMAKI

MIMAKI CJV150 series Bedienungsanleitung

MIMAKI

MIMAKI DM3-1810S Bedienungsanleitung

MIMAKI

MIMAKI CF2 Series Bedienungsanleitung

MIMAKI

MIMAKI JV400-SUV Series Kurzanleitung

MIMAKI

MIMAKI UJF-7151 plus Bedienungsanleitung

MIMAKI

MIMAKI CG-60AR Bedienungsanleitung

MIMAKI

MIMAKI TPC-1000 Bedienungsanleitung

MIMAKI

MIMAKI CG-75FXII Bedienungsanleitung

MIMAKI

MIMAKI DM2-1810 Bedienungsanleitung

MIMAKI

MIMAKI CG-60EX Bedienungsanleitung

MIMAKI

MIMAKI APC-130 Bedienungsanleitung

MIMAKI

MIMAKI TS34-1800A Referenzhandbuch

MIMAKI

MIMAKI CJV150-75 Bedienungsanleitung

MIMAKI

MIMAKI CG-FX SERIES Bedienungsanleitung

MIMAKI

MIMAKI CF22-1225 Bedienungsanleitung

MIMAKI

MIMAKI CF2 Series Bedienungsanleitung

MIMAKI

MIMAKI CG-60SL Bedienungsanleitung

MIMAKI

MIMAKI CG-AR Series Technisches Handbuch

MIMAKI

MIMAKI CF3-1631 Bedienungsanleitung

MIMAKI

MIMAKI CG-60AR Montageanleitung

MIMAKI

MIMAKI CFL-605RT Montageanleitung

MIMAKI

MIMAKI JV33 Series Betriebsanleitung

Beliebte Plotter Handbücher anderer Marken

MUTOH

MUTOH Kona 760 Bedienungsanleitung

HP

HP 7475a Bedienungsanleitung

Vulcan-Hart

Vulcan-Hart FC-500VC Bedienungsanleitung

Roland

Roland TrueVIS VG-640 Betriebsanleitung

Furuno

Furuno RP-180 Bedienungsanleitung

Roland

Roland VersaCamm SP-540V Bedienungsanleitung

Ioline

Ioline Summit Bedienungsanleitung

Summa

Summa S CLASS Bedienungsanleitung

Gerber Technology

Gerber Technology GERBERplotter MP Series Bedienungsanleitung

Furuno

Furuno RP-17 Bedienungsanleitung

HP

HP 7470A Bedienungsanleitung

SII

SII LP-1010 Bedienungsanleitung

Great Computer

Great Computer JII-61 Bedienungsanleitung

Roland

Roland VersaUv LEF - 12i Bedienungsanleitung

Lectra

Lectra Alys 120 Bedienungsanleitung

MUTOH

MUTOH Ultima SC-850D Bedienungsanleitung

Skycut

Skycut D Series Bedienungsanleitung

Commodore

Commodore 1520 Bedienungsanleitung