Minarik MM20000 Series Bedienungsanleitung

1MM23071A-0862 Installation Guide

MM23071A-0862

Connection Guide

This Guide assumes that the user has installed the

MM23071A-0862 drive per user’s manual 250-0091.

This installation must be completed before connecting

and operating the drive. Refer to User’s Manual

250-0091, MM20000 Series Drives, for detailed

installation, operation and troubleshooting information.

Connections

Warning

Do not connect this equipment with power applied.

Failure to heed this directive may result in fire or serious

injury.

Minarik strongly recommends the installation of a

master power switch in the voltage input line, as shown

in Figure 1 (page 3). The switch contacts should be rated

at a minimum of 200% of motor nameplate current and

250 volts.



Power and line fusing connections

• Use 18-24 AWG wire for speed adjust potentiometer

wiring. Use 14–16 AWG wire for AC line (L1 and L2)

and motor (A1 and A2) wiring. Use 18 AWG wire for

field (F1 and F2) wire.

250-0335-readers-spread.qxd 7/3/01 9:56 AM Page 1

2 MM23071A-0862 Installation Guide

Line fusing

Each MM23071A-0862 is shipped from the factory with

two 10A fast blow fuses preinstalled. External line fuses

are not required. Replacement fuses, p/n 050-0013, are

available from Minarik.

Power connections

Connect AC power leads to the drive’s line fuses, or to a

stop switch as shown in Figure 1 (recommended).

Warning

Dynamic braking, inhibit operation and decelerating to a

stop (shorting S1 to S2) may not stop a drive that is

malfunctioning. Removing line voltage (both L1 and L2)

is the only recommended method for emergency stopping.

For this reason, Minarik strongly recommends the

installation of a master power switch in the voltage

input line, as shown in Figure 1. The switch contacts

should be rated at a minimum of 200% of motor

nameplate current and 250 volts.



250-0335-readers-spread.qxd 7/3/01 9:56 AM Page 2

3MM23071A-0862 Installation Guide

Figure 1. Power and Line Fusing Connections

LINE

FUSE

LINE

FUSE

250-0335-readers-spread.qxd 7/3/01 9:56 AM Page 3

4 MM23071A-0862 Installation Guide

Motor, speed adjust potentiometer and field output

connections

Connect the the speed adjust potentiometer, field output

and a DC motor to the drive’s printed circuit board

(PCB) as shown in Figure 2 (page 6).

Refer to User’s Manual 250-0091 for alternative speed

adjust potentiometer and signal input (e.g., voltage

follower) connections.

Speed adjust potentiometer connections

Connect the provided speed adjust potentiometer to S1,

S2 and S3 as shown in Figure 2 (page 6).

Twist the speed adjust potentiometer leads to avoid

picking up unwanted electrical noise. If speed adjust

potentiometer wires are longer than 18 in. (0.5 m), use

shielded cable. Keep speed adjust potentiometer leads

separate from power leads (L1, L2, F1, F2, A1, A2).

Motor connections

Minarik drives supply motor voltage from A1 and A2

terminals. It is assumed throughout this manual that,

when A1 is positive with respect to A2 , the motor will

rotate clockwise (CW) while looking at the output shaft

protruding from the front of the motor. If this is opposite

of the desired rotation, simply reverse the wiring of A1

and A2 with each other.

250-0335-readers-spread.qxd 7/3/01 9:56 AM Page 4

Connect a DC motor to PCB terminals A1 and A2 as

shown in Figure 2 (page 6). Ensure that the motor

voltage rating is consistent with the drive’s output

voltage.

Field output connections

5MM23071A-0862 Installation Guide

Warning

The field output is for shunt wound motors only. Do not

make any connections to F1 and F2 when using a

permanent magnet motor.



See Table 1 for field output connections. Use 18 AWG

wire to connect field output teminals F1 and F2 to a

shunt wound motor.

Table 1. Field Output Connections

Line Voltage Approximate Connect Motor

(VAC) Field Voltage (VDC) Field To

115 50 F1 and L1

115 100 F1 and F2

230 100 F1 and L1

230 200 F1 and F2

250-0335-readers-spread.qxd 7/3/01 9:56 AM Page 5

6 MM23071A-0862 Installation Guide

Figure 2. Motor, Field and

Speed Adjust Potentiometer Connections

NOTES:

1. POWER CONNECTIONS OMITTED FOR CLARITY. REFER TO FIGURE 1

ON PAGE 3 FOR POWER CONNECTIONS.

2. REFER TO TABLE 1 ON PAGE 5 FOR ALTERNATE FIELD

CONNECTIONS. DO NOT CONNECT FIELD OUTPUT IF USING

PERMANENT MAGNET MOTOR.

250-0335-readers-spread.qxd 7/3/01 9:56 AM Page 6

7MM23071A-0862 Installation Guide

Operation

Refer to User’s Manual 250-0091 for detailed operating

information.

Before applying power

• Verify that no conductive material is present on the

printed circuit board.

• Ensure that voltage select switch SW501 and

armature voltage select switch SW502 are set to the

proper positions.

Startup and shutdown

1. Turn the speed adjust potentiometer full

counterclockwise (CCW).

2. Apply AC line voltage.

3. Slowly advance the speed adjust potentiometer

clockwise (CW). The motor slowly accelerates as

the potentiometer is turned CW. Continue until the

desired speed is reached.

4. Set the speed adjust potentiometer to zero. The

motor will decelerate to a stop.

250-0335-readers-spread.qxd 7/3/01 9:56 AM Page 7

8 MM23071A-0862 Installation Guide

901 East Thompson Avenue

Glendale, California 91201-2011

Tel: (800) MINARIK (646-2745)

Fax: (800) 394-6334

www.minarikcorp.com

Document Number 250-0335, Revision 0

PrintedintheU.S.A–6/01

$12.00 North America, $13.00 Outside North America

Warranty information

This product is covered by Minarik’s unconditional

warranty. Refer to User’s Manual 250-0091 or contact

your Minarik representative for more information.

250-0335-readers-spread.qxd 7/3/01 9:56 AM Page 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Minarik Gleichstromantrieb Handbücher

Minarik

Minarik Motor Master 20000 Series Bedienungsanleitung

Minarik

Minarik NRG-2Q Series Bedienungsanleitung

Minarik

Minarik HTL05-D-4Q Bedienungsanleitung

Minarik

Minarik RG501A Bedienungsanleitung

Minarik

Minarik RG5500U Bedienungsanleitung

Minarik

Minarik MMRG30U Bedienungsanleitung

Minarik

Minarik PCM21000A Bedienungsanleitung

Minarik

Minarik XP-AC-SL Series Bedienungsanleitung

Minarik

Minarik DC30-12-4Q-L Bedienungsanleitung

Minarik

Minarik LV Series Bedienungsanleitung

Minarik

Minarik XL1100A Bedienungsanleitung

Minarik

Minarik MM21036A Bedienungsanleitung

Minarik

Minarik M2 Bedienungsanleitung

Minarik

Minarik XP-AC Series Bedienungsanleitung

Minarik

Minarik RG300 Series Bedienungsanleitung

Minarik

Minarik MMRG Series Bedienungsanleitung

Minarik

Minarik NRGD-4Q Series Bedienungsanleitung

Minarik

Minarik BOSS Series Bedienungsanleitung

Minarik

Minarik MMBOSS Series Bedienungsanleitung

Minarik

Minarik MM-PCM Series Bedienungsanleitung

Minarik

Minarik RG500 Series Bedienungsanleitung

Minarik

Minarik PCM23000A Series Bedienungsanleitung

Minarik

Minarik BOSS Series Bedienungsanleitung

Minarik

Minarik C1XP02-115AC Handbuch

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung