Mindray V Series Bedienungsanleitung

Quick Reference Guide

Note: The V-Series Quick Reference Guide is not

intended as a replacement to the Operating Instructions.

Prior to operating equipment, the user must be familiar

with the Operating Instructions Manual contents. This

document is a guideline only to be used as an aid to

comprehensive Inservice Training.

P/N: 0002-08-50038-00 Rev A 3

V12 and V21 Quick Functions Options............................6

Navigation Area Overview .......................................7

Navigation Area Tabs............................................. 8

Patient Info.......................................................9

Enter Demographics ............................................9

Adjust Patient Size ..............................................9

Discharge A Patient ............................................10

Standby .........................................................10

Enter Standby .................................................10

Resume Monitoring............................................10

Privacy Mode....................................................11

Print.............................................................11

Real-Time Waveforms ..........................................11

Adjust Print Location...........................................12

Adjust Waveforms Printing .....................................12

ECG .............................................................13

Adjust ECG Lead ...............................................13

Enable Pacemaker Detection ...................................13

Adjust Arrhythmia and Beat Classification Leads ................14

Adjust QRS Threshold ..........................................14

Initiate Relearn ................................................15

Initiate QT Monitoring .........................................15

Enable QTC Limit ..............................................15

Initiate ST Analysis .............................................16

12 Lead ECG.....................................................16

Enable 12 Lead ECG............................................16

View 12 Lead ECG..............................................16

Print 12 Lead ECG..............................................16

Table of Contents

P/N: 0002-08-50038-00 Rev A 4

NIBP.............................................................17

Initiate A Non-Invasive Blood Pressure Measurement (NIBP).....17

Set A Non-Invasive Blood Pressure Measurement Interval .......18

Invasive Blood Pressures ........................................19

Adjust Invasive Blood Pressure Label ...........................19

Zero Invasive Blood Pressure ...................................19

Overlapping Invasive Blood Pressure Waveforms................20

Temperature ....................................................20

Adjust Temperature Label ......................................20

Adjust Temperature Units ......................................21

Alarms ..........................................................21

Adjust Alarm Limits ............................................21

Adjust Alarm Responses .......................................22

Adjust Arrhythmia Alarms......................................23

Adjust Arrhythmia Alarm Responses............................24

Disable Non-Lethal Arrhythmias................................24

Reset Alarms (Version 2.5 or greater) ......................................25

Pause All Alarms (Version 2.5 or greater) ..................................25

Silence Alarms (Version 2.4 or earlier) .....................................26

Silence All Alarms (Version 2.4 or earlier)..................................26

Transfer .........................................................26

Hemodynamic Monitoring ......................................27

Initiate A Cardiac Output Measurement ........................27

Initiate Pulmonary Artery Wedge Pressure (PAWP) ..............28

Initiate Hemodynamic Calculations.............................29

Table of Contents (cont'd)

P/N: 0002-08-50038-00 Rev A 5

Screen Display ..................................................29

Display Selection ..............................................29

Adjust Display Selection .......................................29

History ..........................................................30

List Trends .....................................................30

Alarm Events ..................................................31

Full Disclosure .................................................31

Volumes.........................................................32

Beat Tone......................................................32

Date and Time...................................................33

Parameter Colors ................................................33

Default (Preset) Settings ........................................33

Lock/Unlocking Touchscreen Display ............................34

Table of Contents (cont'd)

P/N: 0002-08-50038-00 Rev A 6

Quick Functions Options

Alarm LimitsAlarm Limits Alarm

Responses Alarm Watch

Arrhythmia C.O. Run Demographics

Drug

Calculator Events ECG Menu

Full Disclosure Graphic Trends Hemodynamics

Lead/Size List Trends NIBP Stat

PA Insertion Parameters PAWP

12 Lead Privacy Mode Quick Trends

Relearn

Arrhythmia Relearn ST Remote View

Standby Start NIBP ST Review

Transfer/

Discharge

View

All ECG

Zero

All NIBP

Quick Functions Keys (Configurable)

Up to 6 keys may be used in Quick Functions tab

P/N: 0002-08-50038-00 Rev A 7

Buttons (2.5 Software)

Strip Initiates a single strip or a continuous strip print request

Capture Event Saves an event to the event database

History Accesses the Trends, Events, and Full Disclosure dialogs

Audio Pause/O Silences all current and future alarms for the congured time

period. If the congured period is set to Permanent, the

button reads Audio O.

Alarm Acknowledge/Reset Silences the current alarms for the congured time period. If

the congured period is set to Permanent, the button reads

Alarm Reset.

Normal Screen Closes all dialogs and returns to the Main Screen

Navigation Area Overview

Buttons (2.4 Software)

Strip Initiates a single strip or a continuous strip print request

Capture Event Saves an event to the event database

History Accesses the Trends, Events, and Full Disclosure dialogs

Silence All Silences all current and future alarms for the congured time

period

Silence Silences the current alarms for the congured time period

Normal Screen Closes all dialogs and returns to the Main Screen

Quick Functions Tab (Configurable)

Start/Stop NIBP Starts/Stops a NIBP measurement in progress – If there is no

measurement in progress, the button reads Start NIBP

If there is a measurement progress, the button reads Stop NIBP

NIBP Stat Starts an immediate NIBP measurement

Zero All IBP Sets the current pressure for all invasive pressure channels to zero

View All ECG Displays all the ECG waveforms available based on the lead set

currently in use

Lead/Size Accesses the Lead/Size dialog used to change the ECG waveform

height or wave gain

Standby Places the monitor in the standby mode

P/N: 0002-08-50038-00 Rev A 8

Print Tab

Continuous/Abort Begins/ends strips from printing to the thermal printer

Print 12 Lead Prints a 12 Lead Report to the default printer

Print Setup Accesses the Print Setup dialog where the clinician can congure

which waveforms to print and where to print them

Print Queue Accesses the Print Queue dialog

Setup Tab

Patient Info Accesses the Patient Info dialog

Audio Levels Accesses the Audio Levels dialog

Display Accesses the Display Setup dialog

Parameters Accesses the Parameter dialog

System Accesses the System Setup dialog

Tools Tab

Calculators Accesses the Calculators dialog

Alarm Watch Accesses the Alarm Watch dialog

Remote View Accesses the Remote View dialog

System Information Accesses the System Information dialog

VAccess Accesses the VAccess dialog*

Procedures Tab

Note: These buttons are only available when using the Adult or Pediatric patient size

C.O. Run Accesses the Cardiac Output Runs dialog

PAWP Accesses the PAWP dialog

PA Insertion Accesses the PA Insertion dialog.

Hemo Calculations Accesses the Hemodynamic Calculations dialog

12 Lead Accesses the 12 Lead dialog*

Alarms Tab

Limits Accesses the Alarm Limits dialog

Responses Accesses the Responses dialog

Arrhythmia Accesses the Arrhythmia Alarm dialog

Alarm Setup Accesses the Alarm Setup dialog

Navigation Area Tabs

*Only if enabled

Quick Reference Guide

P/N: 0002-08-50038-00 Rev A 9

PATIENT INFO

Enter Demographics

The Patient Info menu allows the clinician to enter and modify patient

demographics.

To enter demographics on V12 or V21 bedside monitor:

a. Select Demographics* (Quick Function tab)

or select Patient Info (Setup tab) to enter Demographics tab

b. Select applicable button to open field and enter patient information

using on screen keyboard

c. Select Accept to accept information on patient name and ID

d. Select Enter to accept information on height, weight, DOB, and age

e. Select Accept to save settings and return to the main screen

Panorama® Central Station Interface: Entering demographic information on

the Panorama Central Station or WorkStation automatically enters it on the

V12 or V21 bedside monitor. Entering demographic information on the V12 or

V21 bedside monitor automatically enters it on the Panorama Central Station,

ViewStation, and WorkStation. Entering Demographics is not required for

patient information to be displayed or stored.

Adjust Patient Size

The Patient Info menu allows the clinician to adjust patient size. To adjust

patient size on the V12 or V21 bedside monitor:

a. Select Demographics* (Quick Function tab)

or select Patient Info (Setup tab) to enter Demographics tab

b. Select Patient Size

c. Select Adult, Pediatric, or Neonate

d. Select Accept to save settings and return to the main screen

Note: Adjusting patient size restores the default (preconfigured) settings

but does not clear patient information or data. Patient size is retained upon

discharge.

Panorama® Central Station: Patient size cannot be changed from the

Panorama Central Station.

*Configurable

P/N: 0002-08-50038-00 Rev A 10

Quick Reference Guide

Discharge A Patient

The Discharge function clears all patient information and restores default

(preconfigured) settings.

To Discharge a patient from the V12 or V21 bedside monitor:

a. Select Discharge* (Quick Function tab)

or select Patient Info (Setup tab) and select Transfer/Discharge tab

b. Select Discharge

c. Select Yes to confirm

Note: After the patient is discharged, default (preconfigured) settings are

restored and Discharged is displayed on the V12 or V21 bedside monitor.

Panorama® Central Station Interface: Discharging a patient on the V12 or

V21 bedside monitor automatically discharges the patient on the Panorama

Central Station, WorkStation, and ViewStation. Discharging the patient on

the Panorama Central Station discharges the patient on the WorkStation,

ViewStation, and V12 or V21 bedside monitor (optional).

STANDBY

Enter Standby

The Standby function allows the clinician to suspend monitoring on a patient.

While in standby, the patient is not monitored; however, all data and settings

are preserved.

To place a patient into Standby on the V12 or V21 bedside monitor:

a. Select Standby* (Quick Function tab)

a. Select Patient Info (Setup tab) and select Standby

Resume Monitoring

Touch anywhere on the screen to remove a patient from Standby and resume

monitoring on the V12 or V21 bedside monitor

*Configurable

Andere Handbücher für V Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mindray Medizinische Geräte Handbücher

Mindray

Mindray M7T Bedienungsanleitung

Mindray

Mindray MR6501 Bedienungsanleitung

Mindray

Mindray WATO EX-65 Bedienungsanleitung

Mindray

Mindray BeneFusion eSP Vet Bedienungsanleitung

Mindray

Mindray V Series Bedienungsanleitung

Mindray

Mindray BeneHeart D3 Bedienungsanleitung

Mindray

Mindray DC-8 Bedienungsanleitung

Mindray

Mindray PM-7000 Bedienungsanleitung

Mindray

Mindray VS9 Bedienungsanleitung

Mindray

Mindray DC-8 EXP Bedienungsanleitung

Mindray

Mindray DC-70T Bedienungsanleitung

Mindray

Mindray DC-70 Bedienungsanleitung

Mindray

Mindray TM70 Bedienungsanleitung

Mindray

Mindray DPM 1 Bedienungsanleitung

Mindray

Mindray BeneVision N22 Bedienungsanleitung

Mindray

Mindray BeneVision N17 Bedienungsanleitung

Mindray

Mindray Resona 7 Bedienungsanleitung

Mindray

Mindray Accutorr 3 Bedienungsanleitung

Mindray

Mindray M8 Elite Bedienungsanleitung

Mindray

Mindray Accutorr 3 Bedienungsanleitung

Mindray

Mindray Accutorr V Bedienungsanleitung

Mindray

Mindray DP-50T Bedienungsanleitung

Mindray

Mindray dpm 3 Bedienungsanleitung

Mindray

Mindray BeneFusion VP5 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung