MINOURA FCG-310 Bedienungsanleitung

FCG-310 & NW-300 instructions manual

This is the instructions for the tools contained in the True-Pro Combo kit.

FCG-310 is the tool to check if the wheel is exactly symmetrical for better ride. You can use FCG-310 on most size

of wheels between 18" and 27"/700c. NW-300 is the spoke nipple wrench for twisting nipples on 14G/15G spokes.

Please read this instructions manual carefully before use to understand how you will do on your bicycle wheel.

IMPORTANT NOTES

FCG-310 is the measuring gauge for bicycle wheel only. Do not use it for any other

purpose than instructed.

FCG-310 is a precision tool so please handle it with care. Do not hit or bend the frame

and gauge plate.

Be careful not to pinch your ngers when openning or closing the FCG-310.

Knob Bolt

Gauge Plate

Ratch

Frame

Rim Guide

Positioning Lib

How To Use FCG-310

1. To open the FCG-310, loosen the Knob Bolt then open the Frame with both hands.

2. Look for the grooves on the inside of the Ratches that x the angle when the Frame is opened.

Extend until the grooves meet and lock into place by pushing them each other.

3. Turn the Gauge Plate counter-clockwise to locate the hole at the down end side.

Put the Gauge Plate on the at groove on the outside of the Ratch.

4. Tighten the Knob Bolt, but you don't need to tighten it so rmly at this moment.

If the Gauge Plate doesn't t to the at

groove on the Ratch correctly, you won't

be able to measure properly. And also

the Gauge Plate will have to be bent.

Please be sure that the Gauge Plate

cannot be replaced.

5. Attach the FCG-310 to the wheel as shown in Fig. A.

While keeping both Rim Guides touching the rim, loosen the Knob Bolt to adjust the Gauge

Plate position, then tighten the Knob Bolt when the Gauge Plate end touches the hub. (Fig. A)

At this moment, make sure the following points;

• Both Rim Guides touch the rim.

• The wheel axle is running through the hole on the Gauge Plate, and the Gauge Plate

touches the hub.

Insert the NW-300 fully to the nipple when tightening. Use exactly same size of wrench

without any wag to protect the nipple. The size indication is just for your reference.

14G

15G 15G

<FCG-310>

<NW-300>

6. Flip over the wheel and attach the FCG-310 onto

the opposite side of the wheel. Do not change the

Gauge Plate position yet.

At this time, if all three points (both Rim Guides

and the tip of the Gauge Plate) touch each

appropriate position at once on both side of

the wheel (see Fig. B), your wheel is properly

assembled and adjusted.

But if either one of the Rim Guides or the Gauge

Plate doesn't touch the appropriate position (see

Fig. C), your wheel needs to be adjusted further.

If the Rim Guide doesn't touch the rim, the wheel has been moved toward opposite side.

If the Gauge Plate doesn't touch the hub even though both Rim Guides touch the rim, your wheel has been

moved backward.

Set the wheel on the wheel truing stand to adjust. To know how to adjust the wheel, refer the instructions

manual of the truing stand.

(Fig. B)

(Fig. C)

Properly Adjusted

Wrong Adjsuted

It is crucial to measure the wheel at several different points to get proper result.

Useful Additional Features

FCG-310 can be used on most wheels sized between 24" and 27"/700c in the standard position.

In addition, you can use it for the smaller wheel (18" or larger) and the wide hub wheel which is used on some DH,

FR and city commuting bikes by changing the the Rim Guide position. (see Fig. D & E)

Make both Rim Guides inward

Step down both Rim Guides

How To Fold Down FCG-310

(Fig. D) (Fig. E)

(Fig. F)

To fold down the FCG-310, 1) loosen the Knob Bolt fully,

2) separate the Ratches as if pulling outward on each other, 3) rotate

the Gauge Plate as the hole faces outward, then 4) fold the Frame.

Do not tighten the Knob Bolt while the hole of the Gauge

Plate is facing inward, otherwise the Gauge Plate will be

bent. Please be sure the Gauge Plate cannot be replaced.

The hole must be outward

How To Use NW-300

Insert the wrench of the NW-300 to the nipple fully to the bottom. Do not use any incorrect (wider) size wrench.

Tighten the nipple slowly. You must stop tightening after turning 1/2 rotation at once at widest. These are for

protecting the nipple from damage. Once the nipple is damaged, you won't be able to continue any work on wheel.

Do not continue using the NW-300 if it doesn't t

your nipples. Use another nipple wrench.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MINOURA Fahrradzubehör Handbücher

MINOURA

MINOURA VERGO-TF Bedienungsanleitung

MINOURA

MINOURA MT-4000SF Bedienungsanleitung

MINOURA

MINOURA FT-50W Bedienungsanleitung

MINOURA

MINOURA BC-V1 Bedienungsanleitung

MINOURA

MINOURA RS-1700 Bedienungsanleitung

MINOURA

MINOURA AC-PRO Bedienungsanleitung

MINOURA

MINOURA SBH-300 Bedienungsanleitung

MINOURA

MINOURA Bike Cradle 4 Bedienungsanleitung

MINOURA

MINOURA SBH-80 Bedienungsanleitung

MINOURA

MINOURA QB-90 Bedienungsanleitung

MINOURA

MINOURA Closet-Cyclist P-600AL-6S Bedienungsanleitung

MINOURA

MINOURA Modoru Kikaku Lusso-mM Bedienungsanleitung

MINOURA

MINOURA DS-150F Bedienungsanleitung

MINOURA

MINOURA BikePit-4 Bedienungsanleitung

MINOURA

MINOURA VERGO TF-1 Bedienungsanleitung

MINOURA

MINOURA LiveRide LR760 Bedienungsanleitung

MINOURA

MINOURA Extra Bike Cradle 3 Bedienungsanleitung

Beliebte Fahrradzubehör Handbücher anderer Marken

Sigma

Sigma BC 16.16 Bedienungsanleitung

Playcore

Playcore Dero Setbacks Bedienungsanleitung

VDO Cyclecomputing

VDO Cyclecomputing x3dw Bedienungsanleitung

Cateye

Cateye RAPID X2 Bedienungsanleitung

buratti meccanica

buratti meccanica Clorofilla Trail Bedienungsanleitung

Shimano

Shimano SG-8R20 Betriebsanleitung

BOB

BOB YAK Bedienungsanleitung

APLIC

APLIC 303303/20190717TW012 Bedienungsanleitung

SRAM

SRAM AXS BlipBox Bedienungsanleitung

Garmin

Garmin EDGE 500 Bedienungsanleitung

Shimano

Shimano FD-RX810 Bedienungsanleitung

Cateye

Cateye V2C - Gebrauchsanweisung

KMART

KMART 43115907 Bedienungsanleitung

SIGMA SPORT

SIGMA SPORT Buster 2000 Bedienungsanleitung

NVO Components

NVO Components STEM Bedienungsanleitung

DAXYS

DAXYS BP188 Bedienungsanleitung

XLC

XLC BV-W17 Bedienungsanleitung

Deda Elementi

Deda Elementi SUPERBOX Bedienungsanleitung