Miranda SDM-872p Bedienungsanleitung

SDM-872p

Radio Frequency Interference and Immunity

This unit generates, uses, and can radiate radio frequency energy. If the unit

is not properly installed and used in accordance with this guide, it may cause

interference with radio communications. Operation with non-certified periph-

eral devices is likely to result in interference with radio and television recep-

tion. This equipment has been tested and complies with the limits in accor-

dance with the specifications in:

- FCC Part 15, Subpart B

- CE EN50081-1:1992

- CE EN50082-1:1992.

How to contact us:

CONTACT MIRANDA

For technical assistance, please contact the Miranda Technical Support centre nearest you:

Americas Asia

Telephone: Telephone:

+1-800-224-7882 +81-3-5730-2987

e-mail: e-mail:

[email protected] [email protected]

Europe, Middle East, Africa, UK France (only)

Telephone: Telephone:

+44 (0) 1491 820222 +33 (0) 1 55 86 87 88

e-mail: e-mail:

[email protected] [email protected]

Visit our web site at www.miranda.com

Guide to Installation and Operation

Contents

page

1 SDM-872p SD/HD Serial Digital to DVI-HDTV

Converter..................................................................... 1

1.1 Introduction............................................................... 1

1.2 Features....................................................................1

2 Overall View................................................................... 2

3 Installation...................................................................... 3

3.1 Power Supply............................................................ 3

3.2 HD/SD Serial Digital Video Input with Active Loop-

through..................................................................... 3

3.3 Digital RGB Video Output......................................... 4

4 Operation........................................................................ 5

4.1 Switch Settings......................................................... 5

4.2 Status LED............................................................... 7

5 Specifications................................................................ 8

Guide to Installation and Operation

1.0

SDM-872p SD/HD Serial Digital to DVI-HDTV Converter

1.1 Introduction

The SDM-872p is a miniature, digital video interface converting

SDI and HDSDI video signal to Digital RGB (DVI-HDTV, DVI-

SDTV) without resizing. The SDM-872p provides automatic input

scan rate detection and supports a wide variety of input formats

including 525i, 625i, 720p, 1080i and 1080p. Output formats are

compliant to EIA/CEA-861-B standard. The primary application is

to convert SD and HD serial to Digital RGB for the purposes of

feeding a computer monitor and projector. (CRT, LCD, Plasma,

DLP, D-ILA etc). In order to support the emerging popularity of

24p equipment and digital display, the SDM-872p DVI output with

selectable 3:2 sequence insertion.

Figure 1 SDM-872p functional block diagram

1.2 Features

- SDI and HD SDI video input with active loop-through

- Digital RGB output compliant to DVI 1.0

- Supports 525i, 625i, 720p, 1080p, 1080i with automatic input

scan rate detection

- Supports direct output, p to PsF, PsF to p, 3:2 insert,

Panasonic Varicam

- Built-in test signal and 4:3 markers

- Compact stand-alone package

DVI

SDI/

HD SDI

LOOP

SD/HD

De-Serializer

Reclocker

Frame

Buffer

Color

Space

Converter

Equalizer

DVI

Serializer

Color bar

Generator

SDM-872p

2.0 Overall View

Figure 2 illustrates the SDM-872p's major parts and their loca-

tions. A high-definition or standard definition digital video source

is connected to the HD/SD SDI IN BNC and the Digital RGB out-

put is provided by the DVI-D connector. Error status is provided

by the status LED. Finally, the power source is connected to the

lockable power connector.

Figure 2 Overall view of the SDM-872p

Input BNC

Power connector

Status LED

Output DVI

Loop-through

BNC

Guide to Installation and Operation

3.0 Installation

3.1 Power Supply

The power supplies LKS-WSU, for 110 V and 220 V operation, is

used to power the SDM-872p. The power supply provides a re-

gulated +5 [email protected] A power source. The SDM-872p employs

a mini XLR-3 connector for its power needs. Figure 3 provides a

detailed pinout of the male connector.

Figure 3 Power connector pinout

3.2 HD/SD Serial Digital Video Input with Active Loop-

Through

Connect a high-definition or standard definition digital video sig-

nal to the BNC labeled HD-SDI IN. The high-definition serial dig-

ital input signal must conform to the SMPTE 292M standard.

The standard definition serial digital input signal must conform to

the SMPTE 259M-C standard.

Make sure that the input signal cable has a maximum length of

75m (250’) and that all serial digital video equipment are con-

nected point-to-point. For instance, there must be a point-to-

point connection between the HD/SD SDI IN BNC and the source

equipment. If a T-connector is used to connect other equipment,

the maximum specified cable length is no longer valid.

+5VDC

GND

Shield

SDM-872p

3.3 Digital RGB Video Output

The digital RGB video output signal (DVI-HDTV) is provided by

the DVI-D (female) labeled OUTPUT. The output format is auto-

matically selected according to the input signal; for a complete

list of the output formats and related SMPTE standards refer to

section 5 Specifications.

Guide to Installation and Operation

4.0 Operation

4.1 Switch Settings

Figure 4.1 outlines the slide switches and pushbutton selection.

Figure 4.1 SDM-872p Underside

Slide Switches selection:

Test Pattern Selection

On: Set the “Test” slide switch to this position to enable

the test pattern on output. The test pattern consists

of a HDTV color bars.

Off: The test pattern is disabled.

Note: in order to output a test pattern, a valid input signal must

be installed.

Miranda Technologies Inc.

Made in Canada

SDM-872p

TEST

SELECT

DIRECT OUTPUT

MARKERS 4:3

INPUT FORMAT

OFF ON

IPsF

OFF

3:2 INSERT

P -> PsF

PsF -> P

VARICAM 1:1

VARICAM 1:2

SDM-872p

Markers 4:3 Selection:

On: Set the “Markers 4:3” slide switch to this position to

display 4:3 markers on the 16:9 image.

Off: The 4:3 markers are disabled.

Input format

I: Set the “Input Format” slide switch to this position

for most input signal.

PsF: Set the “Input Format” slide switch to this position

to access additional output format when input format

is 1920x1080 25PsF.

Pushbutton Selection

The “Select” pushbutton allows the selection of different process-

ing modes, according to the input format. When the pushbutton

is depressed once, the LED indicating the currently selected pro-

cessing mode flashes red and green; when depressed again, the

alternate option LED flashes in its turn if it is available. Confirm

the selection by depressing the pushbutton again. Other pro-

cessing modes are accessed by depressing the pushbutton con-

secutively until the desired mode is reached. For processing

mode A, Band C, both LEDs need to be turned on. See the sup-

ported format table in section 5 Specification for details on

resulting outputs.

Mode A: use this mode to output 25PsF signal from a 24p or

24PsF input signal.

Direct output:

use this selection to output a signal with the same

format as the input signal.

3:2 Insert: inserts a 3:2 sequence to output a 59.94i and 60i signal.

Mode B: reserved for future use

→

PsF: use this selection to output an interlaced signal from

Inhaltsverzeichnis

Andere Miranda Medienkonverter Handbücher

Miranda

Miranda DENSITE IRD-3101 Bedienungsanleitung

Miranda

Miranda Densite IRD-3111 Bedienungsanleitung

Miranda

Miranda picoLink Series Bedienungsanleitung

Miranda

Miranda picoLink Series Bedienungsanleitung

Miranda

Miranda picoLink Series Bedienungsanleitung

Miranda

Miranda ASD-111i Bedienungsanleitung

Miranda

Miranda ASD-211i/2D Bedienungsanleitung

Miranda

Miranda KMV-3901 Bedienungsanleitung

Miranda

Miranda Kaleido-X (7RU) Bedienungsanleitung

Miranda

Miranda dec-291p Bedienungsanleitung

Miranda

Miranda EdgeVision Bedienungsanleitung

Miranda

Miranda DENSITE XVP-1801 Bedienungsanleitung

Miranda

Miranda ASI-Bridge CAM Bedienungsanleitung

Miranda

Miranda ASD-231i Betriebsanleitung

Miranda

Miranda Kaleido-X (7RU) Bedienungsanleitung

Miranda

Miranda Densite ENC-1103 Bedienungsanleitung

Miranda

Miranda Kaleido-Solo Bedienungsanleitung

Miranda

Miranda DENSITE series Bedienungsanleitung

Miranda

Miranda DV-Bridge+ Bedienungsanleitung

Miranda

Miranda KS-900 Bedienungsanleitung

Miranda

Miranda picoLink Series Bedienungsanleitung

Miranda

Miranda XVP-3901 DENSITE series Bedienungsanleitung

Miranda

Miranda ASD-711i Bedienungsanleitung

Miranda

Miranda Quartet Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung