Mitel MiVoice Office 5330e Bedienungsanleitung

Using Your Phone with the Cordless

Module and Accessories 5330e / 5340e

Cordless handsets and cordless headsets provide you with the capability to move around

within your own office or adjacent offices while using your phone.

These cordless devices connect to your IP phone through a Mitel Cordless Module, which

attaches to the back of the phone. There are two Cordless Module types available: Digital

Enhanced Cordless Telecommunications (DECT) and Bluetooth®. The DECT Cordless

Module works with the Mitel DECT Cordless Handset and Mitel DECT Cordless Headset.

The Bluetooth Module works with the Mitel Bluetooth Handset and most third-party

Bluetooth headsets.

The Mitel Cordless Handsets (both DECT and Bluetooth) recharge in the handset cradle. The

Mitel Cordless Headset (DECT only) rests and recharges in a headset cradle that attaches to

the side of the phone.

The Cordless Devices Application (see page ) provides access to the configuration settings

and information screens that apply to the cordless module and accessories.

Note: Since only one module type can be attached to the phone at any given time,

you cannot, for example, use a 5310 Conference Module when a Cordless Module is

attached.

CAUTION: Attempting to remove the back plate on the phone to install a

Cordless Module before disconnecting the phone's power supply may damage

the phone. For details on installing a Cordless Module, see the appropriate

Cordless Module and Accessories Installation Guide for Mitel 5330e/5340e/5360

IP Phones included with the module and available at Mitel OnLine.

DECT Cordless Module and Accessories on 5300 Series IP Phone

Rear View of 5300 Series IP Phone

Elements of Your Cordless Module and

Accessories

Feature

Function

1) Cordless Module

(either DECT or

Bluetooth)

Attached to the back of the phone, the module contains a Light

Emitting Diode (LED) indicating that a cordless device is in use; also

indicates the state of pairing What does this mean?between the module

and a cordless device.

2) Cordless Headset

(photo shows DECT

headset)

Cordless handsfree operation for calls. If you are using a cordless

headset, you do not need to use the handset.

3) Cordless Headset

Charging Cradle

(DECT only)

Provides power to recharge the cordless headset battery. (Not

available for Bluetooth headsets.)

4) Cordless Handset

Charging Plate

Provides power to recharge the cordless handset battery. Replaces the

handset cradle plate supplied with the phone for corded handsets.

5) Cordless Handset

Cordless operation for handset calls. (You can transfer from the phone

handset to the cordless headset at any time.)

6) Cordless Module

Pairing Button

Initiates pairing between the Cordless Module and a cordless

accessory.

7) Cordless Headset

Cradle Cable (DECT

only)

Connects to the Cordless Module to provide power to the charging

cradle.

Handset/Headset Combinations

The following combinations of corded and cordless headset and handset are supported on the

5330e/5340e IP Phone:

•Corded handset only

•Corded handset and corded headset

•Cordless handset only

•Cordless handset and cordless headset

•Corded handset and cordless headset

•Corded headset and cordless handset

The DECT Cordless Handset, DECT Cordless Headset, and Bluetooth Handset are all Mitel-

branded accessories available only from Mitel. Bluetooth headsets are third-party accessories

available from a variety of manufacturers.

Pairing the Cordless Module and

Accessories

Before using a cordless handset or headset, it must establish communication with the

Cordless Module using a procedure called pairing.

Pairing a DECT Cordless Accessory with a DECT

Cordless Module

Notes:

•An IP phone can have only one DECT Cordless Handset and one DECT

Cordless Headset.

•A cordless handset or headset can be paired with only one IP phone at a time.

•Pairing a new cordless handset or headset with the IP phone overwrites the

configuration of any previous handset or headset

•Pairing cannot be performed when the cordless device is already in use.

To pair a DECT cordless accessory:

1. Ensure that the battery of the cordless device to be paired is at least partially charged.

2. Press and hold the pairing button on the back of the Cordless Module (see page ) for 5

seconds to activate phone pairing mode. The LED on the Cordless Module blinks.

The Cordless Devices application opens on the phone and prompts you to place the

accessory in pairing mode.

3. Press and hold the hookswitch on the side of the cordless handset (see page ) or

headset (see page ) for 5 seconds to activate accessory pairing mode. The LED on the

cordless accessory blinks. After a moment, the Cordless Devices application displays

protocol, firmware, hardware, and IPEI information for the device to be paired.

Note: If the LED on the Cordless accessory does not start to blink after 10

seconds, the accessory requires charging or is still in factory battery saving mode

(handset only). Place the accessory on the charger and charge. The green LED

starts to flash indicating that the accessory is charging. It could take up to 60

minutes for the green LED to start flashing. Allow the accessory to fully charge,

approximately 3 hours.

4. Press Yes to confirm pairing. The Cordless Devices application confirms the pairing

by displaying the paired device name and its battery level indicator.

5. Press Close to exit.

Pairing a Bluetooth Accessory with a Bluetooth Module

Notes:

•An IP phone can have one Bluetooth Handset and up to five Bluetooth headsets

(or up to six headsets if no handset is pairedIs paired with what?).

•To pair a new Bluetooth Handset, you must first unpair the existing Bluetooth

Handset.

•Pairing cannot be performed when a Bluetooth device is already in use.

To pair I find these notes confusing –the use of "paired" and "pairing" with no object is an

unusual construction.a Bluetooth accessory:

1. Ensure that the battery of the Bluetooth device to be paired is at least partially

charged.

2. Press and hold the pairing button on the back of the Bluetooth Module for 5 seconds

to activate phone pairing mode. The LED on the Bluetooth Module blinks. The

Cordless Devices application opens on the phone and prompts you to place the

accessory in pairing mode.

3. For Mitel Bluetooth Handsets: Press and hold the hookswitch on the side of the

Bluetooth Handset (see page ) for 5 seconds to activate accessory pairing mode. The

LED on the handset blinks. The pairing confirmation window on the IP Phone

appears, displaying the product name for the device to be paired.

Note: If the LED on the handset does not start to blink after 10 seconds, the handset

requires charging or is still in factory battery saving mode. Place the handset on the

charger. The green LED starts to flash indicating that the handset is charging. It could

take up to 60 minutes for the green LED to start Do you mean "stop" flashing?flashing.

Allow the handset to fully charge, approximately 3 hours.

For third-party Bluetooth headsets: Follow the manufacturer's instructions to place the

Bluetooth headset in pairing mode. The pairing confirmation window on the IP Phone

appears, displaying the product name for the device to be paired.

1. Press Yes to confirm the pairing. The Cordless Devices application prompts you to

enter a passcode.

2. Enter a valid passcode for the Bluetooth device (default is 0000) using the keyboard

on the display, and press OK.

For third-party Bluetooth headsets: An "Auto Connect" window displays. Press Yes if the

phone will not be shared with other users; press No if the phone will be shared with other

users and multiple headsets.

1. The LED on the Bluetooth Module lights and remains lit for a few seconds and then

resumes normal behavior. The Bluetooth device is paired to the Bluetooth Module.

2. Press OK to return to the Cordless Devices application.

3. Press Close to exit the application.

Unpairing an Accessory

To unpair a cordless accessory:

1. Press the blue Menu key and then press Cordless Devices.

2. Press the device name that you want to unpair. The information screen for the selected

device appears.

3. Press Unpair this Device. If the accessory is in use, an error message is displayed.

Otherwise, the accessory is unpaired, removed from the display, and can no longer be

used to interact with the phone.

4. Press Close.

For more information about the Cordless Devices Application, see page .

Cordless Module LED Indicators

The Cordless Module has a blue light-emitting diode (LED) that indicates the current status

of the module:

Blue LED

Function

Solid

Audio is active between the module and either the handset or

headset.

Blinking

Pairing mode is active or a firmware upgrade is in progress.

Off

No audio is active.

Solid for several

seconds

Pairing is successful.

Blinking: LED is On and Off for equal amount of time

Using a Cordless Device as a Remote

Control

When not being used to talk, the buttons on a Mitel-branded cordless handset/headset can act

as a remote control device to change volume and mute settings on the host IP phone. For

example, in a remote hands-free conference setting, the chairman can use the volume and

mute buttons on a cordless device to adjust speaker levels and mute the microphone on an IP

phone that is not within his reach. HTML applications may also make use of the cordless

device buttons, but functionality may differ among applications.

Using the Mute Key on a Cordless Device

When using a Mitel-branded cordless accessory, the Mute key on the cordless accessory is

synchronized with the Mute key on your phone. Pressing the Mute key on either the phone or

the accessory also controls the Mute function on the other device.

There is no synchronization between a third-party Bluetooth headset mute control (if one is

available) and your phone Mute key. The procedure for muting a Bluetooth headset depends

on the headset manufacturer. Some headsets have a mute control and some do not. You can,

however, use the Mute key on your phone to mute a conversation on any type of Bluetooth

headset.

Using the Volume Keys on Cordless Device

When using a Mitel-branded cordless accessory, the Volume keys on the cordless accessory

are synchronized with the Volume keys on your phone. Pressing the Volume keys on either

the phone or the accessory also controls the Volume function on the other device.

When using a third-party Bluetooth headset, the volume control on the headset (if one is

available) is not synchronized with the Volume keys on your phone. Pressing the Volume

keys on the phone does not change the headset volume.

Andere Handbücher für MiVoice Office 5330e

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mitel IP-Telefon Handbücher

Mitel

Mitel 5140 Bedienungsanleitung

Mitel

Mitel Deskphone 6867 Bedienungsanleitung

Mitel

Mitel 5140 Bedienungsanleitung

Mitel

Mitel MiVoice Office 5330e Bedienungsanleitung

Mitel

Mitel OfficeConnect 5340 Bedienungsanleitung

Mitel

Mitel 6869i Bedienungsanleitung

Mitel

Mitel Superset 4015 IP Bedienungsanleitung

Mitel

Mitel 5224 Bedienungsanleitung

Mitel

Mitel 6873i Bedienungsanleitung

Mitel

Mitel MiVoice 5360 Bedienungsanleitung

Mitel

Mitel 6863i Bedienungsanleitung

Mitel

Mitel 3300 5020 Bedienungsanleitung

Mitel

Mitel 5201 Bedienungsanleitung

Mitel

Mitel MiVoice Office 5320e Bedienungsanleitung

Mitel

Mitel SUPERSET 420 Bedienungsanleitung

Mitel

Mitel 600 Bedienungsanleitung

Mitel

Mitel 480G Bedienungsanleitung

Mitel

Mitel NETWORKS 5010 Bedienungsanleitung

Mitel

Mitel 5324 Bedienungsanleitung

Mitel

Mitel Mitel 5330 Bedienungsanleitung

Mitel

Mitel 3600 Produktinformationsblatt

Mitel

Mitel Mitel 5330 Bedienungsanleitung

Mitel

Mitel 5324 IP Bedienungsanleitung

Mitel

Mitel MiVoice Office 5320e Bedienungsanleitung

Beliebte IP-Telefon Handbücher anderer Marken

Alcatel

Alcatel 4028 Bedienungsanleitung

Polycom

Polycom Polycom VVX 600 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 450 Bedienungsanleitung

Cisco

Cisco SPA-500 Series Bedienungsanleitung

Polycom

Polycom SoundPoint IP 650 Bedienungsanleitung

Proximus

Proximus Maestro 3016 IP Bedienungsanleitung

Fanvil

Fanvil X4 Bedienungsanleitung

Cisco

Cisco 7962 Bedienungsanleitung

Snom

Snom 320 Bedienungsanleitung

Yealink

Yealink Yealink SIP-T46G Bedienungsanleitung

Avaya

Avaya 4625SW Bedienungsanleitung

Yealink

Yealink SIP-T52S Bedienungsanleitung

Nortel

Nortel 1140E Bedienungsanleitung

Nexotek

Nexotek NT-P500 Bedienungsanleitung

Avaya

Avaya Integral 5 R3.0 Bedienungsanleitung

GE 28320EE2 - Dect 6.0 InfoLink 2 Bedienungsanleitung

Avaya

Avaya 4600 Series Service-Handbuch

Nortel

Nortel i2050 Bedienungsanleitung