Mitel 5020 IP Bedienungsanleitung
User Guide for the 5020/5220 IP and Superset™ 4025/4125
Telephones
ACD
SUPERVISOR / SENIOR SUPERVISOR
DUE TO THE DYNAMIC NATURE OF THE PRODUCT DESIGN, THE INFORMATION CONTAINED IN
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. MITEL CORPORATION, ITS
AFFILIATES, AND/OR ITS SUBSIDIARIES ASSUME NO RESPONSIBILITY FOR ERRORS AND
OMISSIONS CONTAINED IN THIS INFORMATION.
DbQTU]Qb[_V=9D5<3_b`_bQdY_^
Copyright 2004, MITEL Corporation.
All rights reserved.
i
Contents
Getting Started
Introduction..........................................................................................3
Using a Headset ..................................................................................4
Logging In / Out ...................................................................................7
Queue Status
Queue Status at a Glance..................................................................11
Displaying a Group’s Queue Status ...................................................11
Displaying Reports.............................................................................12
Scrolling Through Reports .................................................................13
About the SHIFT Key.........................................................................15
AGENT STATUS
About Agent Status Keys ...................................................................19
Agent Status at a Glance...................................................................19
Displaying an Agent’s Status..............................................................20
Displaying Agent Status Reports........................................................21
About the Shift Key............................................................................22
AGENT MONITORING
About Agent Monitoring......................................................................27
Agent Help.........................................................................................29
REPORTS AND INDICATORS
Queue Status Reports........................................................................33
Agent Status Reports.........................................................................34
Status Indicators................................................................................35
ADDITIONAL FEATURES
Some Additional Features..................................................................39
GETTING STARTED
3
Introduction
This guide provides instructions for using ACD supervisor and senior supervisor
features on Mitel Networks 5020 IP, 5220 IP, SUPERSET 4025, and SUPERSET
4125 telephone. Refer to your telephone User Guide for a description the
telephone and non-ACD features.
Some of the personal keys on your telephone are programmed as QUEUE
STATUS keys or AGENT STATUS keys, and one may be programmed as a
SHIFT key. You use these keys to monitor the status of agents and agent groups.
Supervisor or senior supervisor?
Supervisors monitor agent groups. Senior supervisors monitor supervisors and
possibly agent groups as well. An agent group can be monitored by either a
supervisor or a senior supervisor, but not both. As a supervisor or senior
supervisor, you can’t answer ACD calls from your telephone.
One or more agent groups?
You’ll have one QUEUE STATUS key programmed on your telephone for each
of your agent groups. If you only have one QUEUE STATUS key (i.e., one agent
group to supervise), you can also have AGENT STATUS keys programmed on
your telephone.
AGENT STATUS keys are not available on senior supervisor phones.
You have easy access to information
A QUEUE STATUS key allows you to access information for an agent group and
for the agents within that group. An AGENT STATUS key displays information for
individual agents within a group.
Once you’ve accessed information, you can display the same type of information
for other agent groups or agents by pressing other QUEUE STATUS keys or
AGENT STATUS keys.
You can exit an information display at anytime by pressing SUPERKEY.
4
Using a Headset
Note: Your system administrator may have enabled full-time headset operation
on your telephone. Phones with full-time headset operation enabled must be
operated only with headsets.
A headset can be used either in regular answer mode or with the Auto Answer
feature programmed.
Most headsets are installed using the same jack that the handset plugs into.
MITEL’s Headset with Feature Control Switch plugs into the dedicated headset
jack (the jack nearest the front of the telephone).
To Install a Headset (no feature control switch)
To install the headset for your use, perform the following tasks:
1. When the telephone is not in use, lift the handset from the cradle and
carefully turn the telephone upside down.
2. Unplug the handset cord where it connects to the telephone.
3. Plug in the headset cord in the same place.
4. Store your handset in a safe place.
To return to handset operation, perform the following tasks:
1. When the telephone is not in use, lift the handset from the cradle and
carefully turn the telephone upside down.
2. Unplug the headset cord where it connects to the telephone.
3. Plug in the handset cord in the same place.
4. Set the telephone upright and return the handset to the cradle.
5. Store your headset in a safe place.
5
To Install a Headset with Feature Control Switch
IMPORTANT NOTE: MITEL’s Headset with Feature Control Switch must be
installed in the dedicated headset jack (the jack nearest the front of the
telephone). Installation will disable your handset microphone.
Disconnecting the headset at the jack or at the quick-disconnect plug
restores handset operation.
To install the headset for your use, perform the following tasks:
1. When the telephone is not in use, lift the handset from the cradle and
carefully turn the telephone upside down.
2. Plug the headset cord into the headset jack (the jack nearest the front
of the telephone).
3. Set the telephone upright and return the handset to the cradle.
To return to handset operation, perform the following tasks:
1. When the telephone is not in use, lift the handset from the cradle and
carefully turn the telephone upside down.
2. Unplug the headset cord where it connects to the telephone.
3. Set the telephone upright and return the handset to the cradle.
4. Store your headset in a safe place.
Enabling/Disabling Headset Operation:
To enable or disable headset operation for headsets on phones that are not
programmed for full-time headset operation:
•Press the HEADSET feature key.
•Connect or disconnect the headset at the quick-disconnect plug
(Headset with Feature Control Switch only).
6
Handling Calls with a Headset (no Feature Control Switch):
To answer a call (when Auto Answer is disabled):
•Press the flashing Line Select key.
To hang up:
•Press CANCEL.
Handling Calls with a Headset with Feature Control Switch:
To answer a call (when Auto Answer is disabled):
•Quickly press and release the Control Switch.
To mute the headset microphone (Headset with Feature Control Switch only):
•Press and hold the Control Switch.
To hang up:
•Quickly press and release the Control Switch.
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Mitel Telefon Handbücher
Mitel
Mitel sx-100 Bedienungsanleitung
Mitel
Mitel MiVoice 6920w Bedienungsanleitung
Mitel
Mitel Deskphone 6869 Bedienungsanleitung
Mitel
Mitel 6970 Bedienungsanleitung
Mitel
Mitel Deskphone 6863 Bedienungsanleitung
Mitel
Mitel MiVoice 6940 Bedienungsanleitung
Mitel
Mitel 6869i Bedienungsanleitung
Mitel
Mitel 6863i Bedienungsanleitung
Mitel
Mitel 6510 Bedienungsanleitung
Mitel
Mitel 6863i Bedienungsanleitung
Mitel
Mitel 6753 Bedienungsanleitung
Mitel
Mitel MiVOICE 6930 Bedienungsanleitung
Mitel
Mitel M2008 Bedienungsanleitung
Mitel
Mitel 3000 Bedienungsanleitung
Mitel
Mitel 3100 ICP - 4.0 L Bedienungsanleitung
Mitel
Mitel 6730a Bedienungsanleitung
Mitel
Mitel M7100 Bedienungsanleitung
Mitel
Mitel 6392 Bedienungsanleitung
Mitel
Mitel ONS/Analog Telephone Bedienungsanleitung
Mitel
Mitel MiVoice 4223 Office Handbuch
